NCR 7360-K429 Manual

Kit Instructions
No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
7360-K429
Issue A

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR FastLane SelfServ™ Checkout is a trademark of NCR Corporation in the
United States and/or other countries. Other product names mentioned in this publication may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms
and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a
customer’s installed software exactly. Therefore, before using this document, consult with your NCR representative or NCR office
for information that is applicable and current.
Copyright © 2022
By NCR Corporation
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved

iii
Revision Record
Issue Date Remarks
AFeb 2020 First Issue

7360-K429 No Handle PIN Pad Mount (Equinox
Luxe 8000i/8500i)
This publication provides procedures for installing a No Handle PIN Pad Mount for an
Equinox Luxe 8000i/8500i device on an NCRFastLane SelfServ™ Checkout (7360) unit.
Note: The Equinox Luxe 8000i/8500i PIN Pad is supplied by the customer.
Kit Contents
Part Number Description
497-0527144 7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) Kit
* 497-0423108 Instructions - Kit (Reference Sheet)
* Items marked with an asterisk are not called out on the image.

27360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
Installation Procedures
Installing the No Handle PIN Pad Mount involves the following procedures:
•Removing Existing PIN Pad Mount on the facing page.
•Installing No Handle PIN Pad Mount on Standard and Convertible Configuration Units on
page4.
•Installing No Handle PIN Pad Mount on a Credit/Debit Only Unit on page6.
•Installing Equinox Luxe 8000i/8500i PIN Pad on page10.
Note: The Equinox Luxe 8000i/8500i PIN Pad is not included in the 7360-K429 No
Handle PIN Pad Kit. For more information, contact an NCRCustomer Service
Representative.

7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) 3
Removing Existing PIN Pad Mount
To remove the existing PIN Pad Mount, follow these steps:
1. Remove the Allen key securing the PIN Pad Mount to the PIN Pad Arm.
2. Lift the PIN Pad Mount to remove the mount from the PIN Pad Arm as shown in
the images below.

47360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
Installing No Handle PIN Pad Mount on Standard and Convertible Con-
figuration Units
To install the PIN Pad Mount on a Standard or Convertible unit, follow these steps:
1. Mount the PIN Pad Mount onto the PIN Pad Arm.
2. Position the PIN Pad Mount so that its edge is approximately parallel with the Pivot
Arm Surface.

7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) 5
3. Fasten the PIN Pad Mount to the PIN Pad Arm using the Allen key.

67360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
Installing No Handle PIN Pad Mount on a Credit/Debit Only Unit
To install the No Handle PIN Pad Mount on a Credit/Debit Only configuration unit,
follow these steps:
1. Using an Allen key, remove two (2) Allen head screws securing the PIN Pad Plate to
the Tilt Arm.
2. Remove the PIN Pad Plate and rotate it to 180°, as shown in the image below.

7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) 7
3. Install the PIN Pad Plate on the Tilt Arm using two (2) Allen head screws.
4. Mount the PIN Pad Mount onto the PIN Pad Arm.

87360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
5. Position the PIN Pad Mount so that its edge is approximately parallel with the Pivot
Arm Surface.

7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) 9
6. Fasten the PIN Pad Mount to the PIN Pad Arm using the Allen key.

10 7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
Installing Equinox Luxe 8000i/8500i PIN Pad
To install the Equinox Luxe 8000i/8500i PIN Pad, follow these steps:
Note: For the purpose of illustration only, this procedure shows images using a
Standard Configuration unit.
Note: The Equinox Luxe 8000i/8500i PIN Pad is not included in the 7360-K429 No
Handle PIN Pad Kit. For more information, contact an NCRCustomer Service
Representative.
1. Connect the PIN Pad cable to the RS232/A port of the Primary Terminal Display.
2. Do the following:
a. Route the PIN Pad cable down to the back panel opening for the PIN Pad arm.
b. Route the PIN Pad cable through the cable clamps under the PIN Pad arm and
out of the PIN Pad Mount, as shown in the image below.
Note: On a Credit/Debit Only Configuration, route the cable through the PIN
Pad arm and out of the PIN Pad Mount.

7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i) 11
3. Turn the PIN Pad over and then connect the cable to the PIN Pad port by pushing
the cable at an angle, as shown in the image below.
4. Press the cable to lock in place and then secure the cable to the PIN Pad using a
screw, as shown in the image below.

12 7360-K429 No Handle PIN Pad Mount (Equinox Luxe
8000i/8500i)
5. Mount the PIN Pad to the four (4) studs at the back of the PIN Pad Mount, as shown
in the image below.
Note: The maximum vertical tilt is 80° and the minimum vertical tilt is 20° as shown
in the image below.