NEC FA Series User manual

Fine Pitch LED Video Display Indoor
NEC FA Series & FE Series
LED Wall Bundle
Quick Start GUIDE
For models:
LED-FA012i2 (110 inch)
LED-FA015i2 (137 inch)
LED-FA019i2 (110 inch)
LED-FA019i2 (165 inch)
LED-FA025i2 (220 inch)
LED-FE012i2 (110 inch)
LED-FE015i2 (137 inch)
LED-FE019i2 (110 inch)
LED-FE019i2 (165 inch)
LED-FE025i2 (220 inch)
2020-08-18
Version 2.0

Languages:
English Page 3
Russian Page 19
Turkish Page 35
Arabic Page 51

Fine Pitch LED Video Display Indoor
NEC FA Series & FE Series
LED Wall Bundle
Quick Start GUIDE - ENGLISH
For models:
LED-FA012i2 (110 inch)
LED-FA015i2 (137 inch)
LED-FA019i2 (110 inch)
LED-FA019i2 (165 inch)
LED-FA025i2 (220 inch)
LED-FE012i2 (110 inch)
LED-FE015i2 (137 inch)
LED-FE019i2 (110 inch)
LED-FE019i2 (165 inch)
LED-FE025i2 (220 inch)
2020-08-18
Version 2.0

4
Table of Contents
1. About this User Guide................................................................................... 5
1.1 Safety Symbols Used in this Manual .............................................................................................. 5
2. Safety and Compliance Guidelines................................................................. 6
2.1 Qualication of Personnel...................................................................................................................6
2.2 Personal Protection...............................................................................................................................6
2.3 General Safety Guidelines...................................................................................................................6
2.3.1 Risk of Fire...............................................................................................................................................7
2.4 Safety for Electricity and Power Supply .........................................................................................7
2.5 Safe Usage of LED Lamps....................................................................................................................8
3. About The LED WALL..................................................................................... 9
3.1 Turn on the LED Wall.............................................................................................................................9
4. The Video Controller ...................................................................................11
4.1 Front and Rear Panel..........................................................................................................................11
4.2 Display and Menu............................................................................................................................... 12
4.2.1 Select an Input Source .................................................................................................................... 12
4.2.2 Adjust the Brightness.......................................................................................................................13
5. Troubleshooting.........................................................................................14
6. Disposal.....................................................................................................15
6.1 Within the European Union............................................................................................................. 15
6.2 Outside the European Union.......................................................................................................... 15
7. Copyright and Disclaimer ............................................................................16
7.1 Copyright ...............................................................................................................................................16
7.2 Disclaimer ..............................................................................................................................................16
8. Service & Support in Europe.........................................................................17

5
1. AboutthisUserGuide
Dear customer,
Thank you for choosing one of NEC DISPLAY SOLUTIONS’ne pitch direct view LED
display systems.
In this NEC Quick Start Guide, you can nd a short overview about the components
and handling of the LED Wall.
We hope your experience with our product meets or exceeds your expectations.
Please contact us if you have any questions.
1.1 SafetySymbolsUsedinthisManual
Safety instructions emphasize potential hazards for personal injury or property
damage. This manual uses the following safety notices to indicate the severity of a
potential hazard:
Warning!
A warning for a potentially hazardous situation that can result in death,
personal injury, or property damage if not adhered to.
Caution!
A recommendation for a potentially hazardous situation that may
result in personal injury or property damage if not adhered to.
Notice
A recommendation for a potentially hazardous situation that may result in property damage
if not adhered to.

6
2. SafetyandComplianceGuidelines
Read the instruction manuals carefully and follow the given instructions and safety
information thoroughly.
The operating safety of the system is only ensured through its proper use.
Only operate the system with supplied accessories and tools.
2.1 QualicationofPersonnel
Only authorized and qualied technical personnel can perform the installation.
Only personal qualied by NEC DISPLAY SOLUTIONS and/or respectively authorized
personal may carry out repairs, service and maintenance work on the system. A
case of service occurs as soon as one component is damaged in any way, is not fully
functional any more.
Only trained personnel, such as electricians or NEC personnel, may connect the
internal power supply to mains power supply.
2.2 PersonalProtection
Warning!
Electric shock hazards.
Follow the relevant legal electric requirements of the country, where the system
will be operated, as well as the existing regulations of the operator, such as work,
operating and safety regulations.
2.3 GeneralSafetyGuidelines
Warning!
Risk of electric shock or re due to high-voltage components.
• Do not expose this unit to rain or moisture.
• Do not submerge this unit partially, or completely in water, or liquids.
• Do not use this unit’s polarized plug with an extension cord receptacle or other
outlets unless the prongs can be fully inserted.
• Do not open the cabinet because of the high-voltage components inside. There are
no user-serviceable parts are inside.
• Only qualied service personnel are allowed to service and open the unit.
Caution!
Risk of electric shock.
• If not in use, fully disengage the power to the unit by disconnecting the power cord
from the AC outlet.
• Do not use damaged cables. Check cables regularly. Replace damaged cables
immediately, they are not user-serviceable.

7
Caution!
Risk of re and product damage by aggressive substances.
• Keep the system away from aggressive substances, inammable gases
and vapors.
• Clean the unit only with materials or chemicals that are inert,
nonabrasive, noncorrosive and non-marking. Consult the
manufacturer for further advice should any doubts exist regarding any
cleaning procedure.
Caution!
Risk of re, injuries and product damage.
• Keep the system away from ammable material.
• Never block the air ventilation spaces around the LED Wall. Keep them free at all
times.
• Only use the supplied cables, which are t for the system and its components.
Caution!
Risk of product damage due to dusty environment.
Do not operate the system in a dusty environment.
Caution!
Risk of product damage by moisture or water.
Do not clean the system with water. Do not wipe the LED Pixel Cards with a damp cloth.
2.3.1 RiskofFire
Keep ammable materials away from the installation. During operation a lot of
energy is transferred into heat.
Proper ventilation must be provided. Never block the air ventilation holes. Keep them
free at all times.
2.4 SafetyforElectricityandPowerSupply
The electrical systems and their components are not to be opened. The parts inside
modules, which are not user-serviceable, hold high voltages, including when these
components are not in-use for a long time. Accessing these components may lead to
serious injury, or property damage.
Only authorized and qualied personnel may open the system and its
components! All repairs to the system may only be carried out by NEC DISPLAY
SOLUTIONS and/or by respectively authorized and qualied technical personnel.

8
• The limit values specied in the technical data must never be exceeded.
• Do not operate or touch the system with wet hands.
2.5 SafeUsageofLEDLamps
Caution!
Risk of product damage due to static electricity and surge voltage.
Do not touch the LED display areas.
Caution!
Risk of product damage due to moisture.
The LED lamps may absorb and hold moisture during the LED module
installation or if not used for a long time. Therefore, in such cases, the
brightness must be increased gradually during a break-in period before
setting the normal brightness.
If the LED lamps are lit with 100% brightness while moisture is retained,
the temperature will rise very quickly and the water inside the lamps will
evaporate and expand. This will cause the encapsulating resin to expand,
which may lead to separation of the boundary surface inside the LED
lamps. This separation can cause the LED lamps not to light up properly.
Lampbreak-in
Congure the brightness settings as shown below with a video displayed on the
LED module. After a break-in period of approx. 3 hours, the LED module can be used
under normal conditions.
Time since start-up:
0 hour 1 hour 2 hours 3 hours
(just after start-up)
Full white
Video content
60%40% 80% Normal operation
Brightness
value 20% 50% 70% Normal operation

9
3. AboutTheLEDWALL
The LED Wall is a high denition LED display product in 16:9 ratio with a high contrast
ratio and refresh rate.
The LED Wall consists of single LED modules, which are interconnected and centrally
controlled. The quantity of the modules depends on the size of your LED Wall.
To display videos, the LED Wall is connected to a video controller. The controller
receives the video input and the control signal from PCs. The Controller converts the
video input signal from the source and sends the video signal to the LED Wall. To
monitor the input source, a regular screen can be connected to the video controller.
Figure 1: General Setup of the LED Wall and Video Controller
ALED Wall FInput Source for Monitoring
BVideo Controller (NovaStar MCTRL660 PRO) GVideo Input to Video Controller
CVideo Output to LED Wall HSource PC with Video Input Material
DPower Supply IControl Signal
EMonitoring Screen JPC with Control Software NovaLCT
B
JHE
C
D
D
I G F

10
3.1 TurnontheLEDWall
Notice
The electrical setup of the LED Wall and the video input setup depends on individual customer
requirements. Below, you can nd the most common setups. Before following the instructions, please
ensure that your system ts one of the described setups.
How to turn on the LED Wall, depends on the electrical setup for the LED Wall.
1) The LED Wall is directly connected to mains
The LED Wall is always powered on and turns black if not needed (no
video input).
1. Ensure the video controller and the control PC is turned on.
2. Start the video input on the PC with the video material.
Result: The LED Wall displays the video material.
2) The LED Wall is has to be plugged in to mains (only for smaller LED Walls)
1. Plug in the LED Wall to mains. The amount and type of plugs depends on the
LED Wall setup and your region.
2. Ensure the video controller and the control PC is turned on.
3. Start the video input on the PC with the video material.
Result: The LED Wall displays the video material.
3) Setup with SX ON/OFF Switch
The LED Wall and video controller are connected to a SX ON/OFF
Switch, which turns the LED Wall and the video controller on and o.
1. Press the SX ON/OFF Switch on the system control rack.
2. Ensure the control PC is turned on.
3. Start the video input on the PC with the video material.
Result: The LED Wall displays the video material.