NEC MultiSync X401S User manual

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 1 of 9
Contents:
Product Description and Notes Page 1
Tilt Angle and Rotation Page 1
Ventilation Requirements Page 2
Display Dimensions Page 3
Display Dimensions Page 4
Optional Table Top Stand Dimensions Page 5
Dimensions with Optional Wall Mount (WMK-4655S) Page 6
Dimensions of Optional Wall Mount (WMK-4655S) Page 7
Input Terminals Page 8
Control Codes Page 9
Product Description
Type: LCD Display Screen Surface: Anti-Reflective
Resolution: 1920 x 1080 Dimensions without stand: 36.4”(W) x 21.2”(H) x 1.7”(D)
Aspect Ratio: 16:9 Dimensions with stand: 36.4W) x 22.6”(H) x 9.4” (D)
FCC: Class B Weight without stand: 32.8 lbs / 14.9 kg
Power Consumption: 110W (typ) Weight with stand: 35.9 lbs / 16.3 kg
BTU’s: 375.34 BTU/hour Built-In Speaker
NOTES:
This document is intended to be used as a reference guide to supply useful information for a design or installation. It is not
intended to be a step-by step procedure for installation.
Any ceilings or walls must be strong enough to support the monitor and the installation must be in accordance with any local
building codes. All mounts should make secure contact to wood studs.
4:3 sources can be displayed on the 16:9 screen in either normal aspect ratio with bars on the left or right, or stretched horizontally
to fill the screen using the menus (see “Aspect Modes” in menus and user manual).
Distances are in inches, for millimeters multiply by 25.4.
Tilt Angle and Rotation
Monitor may be angled and rotated from normal landscape and portrait orientation to both face up and face down positioning. When
orientated in face up or face down position, operating temperature for the unit changes. Rotate only clockwise for portrait orientation.
Operating Temperatures:
oLandscape: 5-40° Celsius; 41-104° Fahrenheit Face Up: 5-35° Celsius; 41-95° Fahrenheit
oPortrait: 5-40° Celsius; 41-104° Fahrenheit Face Down: 5-35° Celsius; 41-95° Fahrenheit

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 2 of 9
Ventilation Recommendations:
Dimensions below are minimum recommended for proper ventilation when the unit is in a recessed area.
NOTE:
The ventilation space should not be covered or closed off at the front of the opening. If for some reason the opening needs to be covered, other
means of ventilation will need to be incorporated into the design. Contact NEC for design review and recommendations.

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 3 of 9
Display dimensions:

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 4 of 9
Display dimensions (cont.):

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 5 of 9
Optional Table Top Stand Dimensions (ST-322):

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 6 of 9
Dimensions with Optional Slim Wall Mount (WMK-4655S)
Dimensions with Optional Slim Wall Mount (WMK-4655S) when OPS installed
Note:
If an OPS option card is installed, offset spacers must be utilized. See WMK-4655S manual.

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 7 of 9
Dimensions with Optional Wall Mount Kit (WMK-4655S):
NOTE: Mount shown without offset spacers

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 8 of 9
Input Panels:
Bottom:
Side:

NEC Display Solutions of America, Inc.
X401S Installation Guide
40” LCD Display Rev 1.0
www.necdisplay.com X401S Page 9 of 9
Control Codes:
NOTE: Contact your NEC rep for codes not listed.
NOTE: Use a cross/reverse/null modem cable.
Cable Connection:
Communication Protocol:
Interface: RS-232C Parity: None
Communication: Asynchronous Stop Bit: 1 bit
Baud Rate: 9600 bps Communication Code: Hex
Data Length: 8 bits
PC Control Connector (D-Sub 9P)
NOTE: If so desired, jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
These connections are not required. The only connections required are pins 2 (TxD), 3 (RxD) and 5 (GND).