NEC N8143-56F/56E User manual

１
Keep this User’s Guide at hand for quick reference at any time it may be required.
Read “SAFETY NOTES”first, then set up this kit.
Provide this User’s Guide along with this kit when you transfer to the third party.
This product is mechanical parts for installing NEC Express server into 19-inch rack system.
Read this document and the manual of the NEC Express server to understand installation
method before installing this product to the server.
Follow instructions given in this document for proper installation and safe use of the server.
Refer to the User’s guide of the NEC Express server regarding the safety indications.
Install this kit only to the server which define as optional parts
.
Failure to follow these instructions may cause the server to operate
incorrectly and/or personal injury or damages of surrounding servers to
occur.
More than two persons are required to carry or install the rack.
Failure to follow this instruction may cause the rack to fall to result in
personal injury and/or breakage of surrounding servers.
Read this document and the manual of the NEC Express server to
understand installation method before installing this product to the
server.Failure to follow these instructions may cause the server to
operate incorrectly and/or personal injury or damages of surrounding
servers to occur.
Attach cablesnot to contact the slide rail assembly and neighboring
units. Failure to follow these instructions may cause the server to
operate incorrectly and/or personal injury or damages of surrounding
servers to occur.
Do not disassemble, repair, or modify the server. Otherwise, an electric
shock or fire may be caused.
N8143-56F/56E Rack Conversion Kit
User’s Guide
SAFTY NOTES
856-122660-101-A Rev.1.2
Preface

２
Chapter 1
Preparation for Installation
This chapter describes preparations required for installing the server on a 19-inch rack step by
step.
Step 1 Unpacking
The rack conversion kit contains the following components. Make sure that everything listed
below are inside and no damage is observed after unpacking.
19
18
17
56
1
2
3
78910
11
12
13,14
15
16
20
21
22
4

３
No.
Part Name QTY
Notes
1Front Cover 1
2Slide Rail Assembly 2
3Cable Arm 1
4Arm Bracket 1
5Arm Stopper 1
6Arm Support (1) 1EIA Mounting Flange to Rear
Mounting Flange : 700_743mm
7Arm Support (2) 1EIA Mounting Flange to Rear
Mounting Flange : 743_900mm
8Foot Cover 4
9Device Cover 3For 5.25”bay
10 HDD Cover (1) 1For Fixed HDD model
11 HDD Cover (2) 1For Hot Plug ATA HDD model
12 Template 1
13 Model Name Label 1120Lg／120Ef 用
14 Model Name Label 1120Lh／120Lg 用
15 Icon Label 1
16 Washer 8For fixing the slide rail assembly
17 Screw A 8M4 Bind-head screws
(color :Gold)
18 Screw B 10 M5 Bind-head screws
19 Screw C 8#6-32UNC pan-head screws
(color :silver)
20 Screw D 11 M4 pan-head screws with
Washer (color :Gold)
21 Cable Tie 10
22 User’s Guide 1This manual
Step 2 Preparing the Required Tools
Required tools are listed below.
?
Phillips screwdriver

４
Device Cover
Chapter 2
Installation
This chapter describes the procedures for installing the rack mountable server into a 19-inch
rack.
Step 1 Convert from tower type to rack-mount type
(1) Pull the hinge pin out. Then slide the front bezel to remove it from the other hinge
pin and remove the front bezel.
(2) Remove the bezel hinge. (four screws)
(3) Remove five nylon rivets from the top cover.
(4) Remove four feet from the bottom chassis. (Total eight screws)
(5) Fix the device covers together with the dummy covers
which were installed to blank bays in the chassis.
Front Bezel
Foot
Hinge Pin
Nylon Rivet
Bezel Hinge
Front Bezel

５
(6) Fix the HDD cover (1 or 2) with the screw (D) to the inside of front cover.
( Do not attach the HDD cover into Hot Plug SCSI HDD (6slots) model. )
?
Fixed HDD (4slots) model
Fix HDD cover (1) with four screws (D)
?
Hot Plug ATA HDD (4slots) model
Fix HDD cover (2) with two screws (D)
(7) Fix four foot covers with four screws (C) to the bottom of server.
(8) Fix the front cover with four screws (C) to the front of server.
Foot Cover
Front Cover
Front Cover
HDD Cover (1)
HDD Cover (2)
Front Cover

６
Step2 Mounting the server into the rack
(1) Fully slide the rails out until they lock in place. And while pressing down on the
release lever, slide the rails to remove the inner rail.
(2) Fix the inner rail with eight screws (A) to both sides of the server.
(3) Place the template in the desired location of the rack and attach four core nuts that
come with the rack assembly to the mount flange in the rack.
Release Lever
Slide Rail Assembly
Outer Rail
Inner Rail
Core nut positions
Slide Rail
Front side
Core nut positions
Cable Arm position
Slide Rail
Back side

７
(4) Loosen three screws for fixing the rear mounting bracket in order to move the rear
mounting bracket. Repeat this step for the other rail.
(5) Place slide rail assemblies to the mounting flanges of the rack. Attach the washer to
the screw (B) and then fix both sides of slide rails with eight screws (B).
Refer to the template for the position.
(6) Tighten six screws that were loosened in (4).
Front side
Back side
Rear Mounting
Outer Rail
Slide Rail Assembly
Screws
for Rear Mounting bracket

８
(7) Slide two slide rails out from the rack until they were locked. And then with three or
more persons assisting you, lift the server and align the inner rails attached to the
both side of the server with the extended rails.
(8) Insert the inner rails into the extended slide rails and push the server into the rack
until it stops.
(9) Carefully press down the release levers on the inner rails to release the locks and slide
the server all the way into the rack.
(10) To check that the server slides in and out of the rack, grasp the two handles on the
front of the server slowly pull the server out and push it back in.
(11) Tighten the four captive thumbscrews to secure the server to the rack.
Note sufficiently that your fingers may not be caught between a
rail and other mechanical partsor cut by a rail at installation or
removal of the server from the rack.
?
Do not connect any cables before attaching the cable arm.
?
Secure four captive thumbscrews when mounting the server to the rack.
Captive thumbscrews
Front Cover
Release Lever

９
Step 3 Installing the cable arm and cables
(1) Fix the arm bracket with two screws (D)to the back of the server.
(2) When the distance between the front mounting flange and the rear mounting flange is
about 743mm, align one end of the cable arm with the outside of the core nuts
installed to the rear of the rack frame and secure it with the two screws (B).
Server
Arm Bracket

１０
(3) When the distance is from 700mm to 742mm, use the arm support (1) to adjust the
position of cable arm.
(4) When the distance is from 745mm to 900mm, use the arm support (2) to adjust the
position of cable arm..
(5) Align the small holes in the cable arm and the arm bracket, and then fix the cable arm
with two screws (D) to the arm bracket that fixed in step (1).
Distance between the front mounting
flange and the rear mounting flange：
700_742mm
Cable Arm
Att
ach the cable arm
to the arm support
to
shorten this distance
as much as possible.
Cable Arm
Arm Support (2)
Arm Support (1)
Cable Arm
Arm Bracket
Small Hole
Distance between the front mounting
flange and the rear mounting flange：
745_900mm