NEC WMK-3298T User manual

12019-12-18 #:126-9246-3 (2020-03-02)
ENG
32" - 98"
(82 - 249 cm)
210 lb
(95 kg)
MAX
WMK-3298T
NEC DISPLAY SOLUTIONS OF AMERICA, INC.

22019-12-18 #:126-9246-3 (2020-03-02)
ENG - This product is designed to be installed on wood stud, solid concrete or cinder block walls. Hardware is
included for wood stud, solid concrete and cinder block installation. Before installing make sure the supporting
surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be

WARNING
Symbols
ENG
WARNING
ENG
#
Skip to step.
ENG Display center.
ENG
x3
Screws must get at
least three full turns

ENG Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
5/32"
(4mm)

(8mm)
3/8"
(10mm)

32019-12-18 #:126-9246-3 (2020-03-02)
Parts (Before beginning, make sure you have all parts shown below).
ENG
B (1)
right tilt bracket
A (1)
wall plate
F (1)
D (6)8mm concrete anchor
E (6)
#14 x 2-1/2" wood screw

G (4)
4mm allen
wrench
C (1)
left tilt bracket
J (4)
I (4)
K (8)N (4)
Parts List
Part #Description Qty
Awall plate 1 203-1037
Bleft tilt bracket 1 203-1039
Cright tilt bracket 1 203-1038
D#14 x 2.5 wood screw 5S1-015-C03
Econcrete anchor 590-0320
F4mm allen wrench 1 
G 4 520-1050
H 4 520-1132
Imulti washer 4 
JM8 x 15mm socket pin screw 4 
K 8 510-1114
Lextension brackets 2 
M18 x 1mm security allen wrench 1 
N 4 510-1087
M (1)
L (2)
extension
bracket
18 x 1mm allen wrench
multi washer
M8 x 15mm
 
H (4)


42019-12-18 #:126-9246-3 (2020-03-02)
1
1b
Wood stud wall.
ENG
1a
1a
ENG - When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that
the wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".
WARNING
1a-2
Level wallplate. Mark mounting holes on stud
center lines.
ENG
1a-1 
mark stud center lines.
ENG
A
Concrete/Cinder block.
ENG

(41cm)

52019-12-18 #:126-9246-3 (2020-03-02)
1a-3
1a-4
Mounting hole must center on stud.
ENG
5/32"
(4mm)
Drill mounting holes into supporting surface

ENG
2.5"

5/32"
(4mm)
Level wallplate. Install using wood
screws provided.
ENG
2
Maximum 80 in. • lb (9 N.M.).
ENG
3/8"
(10mm)
A
D (4)

62019-12-18 #:126-9246-3 (2020-03-02)
1b
ENG - When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi. When installing Peerless wall mounts on a cinder block wall, the cinder blocks

Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. It is
suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity. Never attach concrete expansion anchors to

WARNING
2.5"


(8mm)
1b-1
1b-2
Level wallplate. Mark mounting holes.
ENG

(8mm)
Do not drill into mortar joints.
ENG
Drill mounting holes into supporting surface

ENG
8"
(20cm)
8"
(20cm)
A

72019-12-18 #:126-9246-3 (2020-03-02)
1b-4
Level wallplate. Install using concrete
anchors and wood screws provided.
ENG
3/8"
(10mm)
1b-3
Maximum 80 in. • lb (9 N.M.).
ENG
E

ENG
A
D (4)
E (4)

82019-12-18 #:126-9246-3 (2020-03-02)
2
Use chart to determine orientation, vesa pattern and hardware for your display.
ENG
Mounting Hardware
Display Model # Orientation Vesa
E327 landscape 100x100 
E437Q landscape 200x200 
E507Q landscape 400x200 
E557Q landscape 400x200 
E657Q landscape 400x200 
IB554Q-2.1 landscape 300x300 
IB654Q-2.1 landscape 400x400 M8 x 15
IB754Q-2.1 landscape 400x400 M8 x 15
IB864Q-2.1 landscape 400x400 M8 x 15
C431 landscape/portrait 300x300 
C501 landscape/portrait 300x300 
C551 landscape/portrait 300x300 
C651Q/V654Q landscape/portrait 400x400 M8 x 15
C751Q/V754Q landscape/portrait 400x400 M8 x 15
C861Q/V864Q landscape/portrait 400x400 M8 x 15
C981Q/V864Q landscape/portrait 400x400 M8 x 15
P404/V404 landscape/portrait 300x300 
P484/V484 landscape/portrait 300x300 
P554/V554 landscape/portrait 300x300 
V323-3 landscape/portrait 200x200 
V554Q landscape/portrait 300x300 

92019-12-18 #:126-9246-3 (2020-03-02)
3a
3
3b3a
Without extension brackets.
ENG
With extension brackets.
ENG
K (8)
B
L (2)
C
VESA 100 X 100:VESA 300 X 300:
VESA 400 X 400: VESA 200 X 200:
VESA 400 X 200:
F

10 2019-12-18 #:126-9246-3 (2020-03-02)
Center adaptor brackets vertically on back of
screen.
ENG
X
X
BC
3a-1
X
X
B C