NEC 320Fc Manual

Read Me First: Unpacking
Express5800/320Fc Systems
NEC Corporation of America
456-01722-000

Notice
The information contained in this document is subject to change without notice.
UNLESS EXPRESSLY SET FORTH IN A WRITTEN AGREEMENT SIGNED BY
AN AUTHORIZED REPRESENTATIVE OF NEC, NEC MAKES NO WARRANTY
OR REPRESENTATION OF ANY KIND WITH RESPECT TO THE INFORMATION
CONTAINED HEREIN, INCLUDING WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PURPOSE. NEC assumes no responsibility or obligation of any
kind for any errors contained herein or in connection with the furnishing,
performance, or use of this document.
Software described in NEC (a) is the property of NEC and/or its licensees, (b) is
furnished only under license, and (c) may be copied or used only as expressly
permitted under the terms of the license.
NEC documentation describes all supported features of the user interfaces and the
application programming interfaces (API) developed by NEC and/or its licensees.
Any undocumented features of these interfaces are intended solely for use by NEC
personnel and are subject to change without warning.
This document is protected by copyright. All rights are reserved. No part of this
document may be copied, reproduced, or translated, either mechanically or
electronically, without the prior written consent of NEC Corporation of America.
The NEC Corporation of America logo, Express5800/320Fc, and the
Express5800/320Fc logo, are trademarks of NEC Corporation of America.
ActiveService Network is a trademark of Stratus Technologies Bermuda, Ltd. All
other trademarks and trade names are the property of their respective owners.
Manual Name: Read Me First: Unpacking Express5800/320Fc Systems
Part Number: 456-01722-000
Revision Number: 0
Publication Date: August 2007
NEC Corporation of America
10850 Gold Center Drive, Suite 200
Rancho Cordova, CA 95670
© 2007NEC Corporation of America. All rights reserved.

-iii-
Contents
Introduction 1
Before Unpacking the System 4
Unpacking the System 4
Disposing of Packing Materials 6
What to Do Next 6

-iv-

-1-
Introduction
Read Me First: Unpacking Express5800/320Fc Systems
explains how to unpack a system from its shipping box.
WARNING
!
To avoid eye and skin injuries, be careful
when cutting the shipping straps from the
shipping box. The straps can snap with
considerable force when cut.
WARNING
!
To avoid back injury, do not attempt to remove
an enclosure before you remove the shipping
box from the shipping pallet. When the
shipping box is removed, lift and remove each
enclosure with the assistance of another
person.
WARNING
!
To avoid back injury, enlist the assistance of
another person to lift and remove the
enclosures and pedestal case.

-2-
Figure 1 shows the packaged components, and the order in which
to remove them, for a rack-mounted system. Figure 2 shows the
packaged components, and the order in which to remove them, for
a pedestal system.
Figure 1. Unpacking a Rack-Mounted System
1 Accessories box
2 Shipping box
3 Shelf unit
4 and 5 CPU-I/O enclosures
asys072
3
2
1
4
5

-3-
Figure 2. Unpacking a Pedestal System
1 Pedestal case
2 Accessories box
3 Shipping box
4 and 5 CPU-I/O enclosures
asys073
3
2
1
4
5

-4-
Before Unpacking the System
•Check the label or the packing slip on the outside of the
shipping box to verify that you received the correct shipment.
Depending on your order, you have received either a
rack-mountable system or a pedestal system.
•Verify that the Tip-N-Tell and Shockwatch indicators on the
outer sides of the shipping box are not activated.
CAUTION
!
Do not unpack the system if you did not receive
the correct shipment, or if an indicator on the
shipping box is activated. Contact the shipping
carrier and the purchasing agent for your system
immediately.
Unpacking the System
Tools needed: A pair of scissors or a utility knife
1. Place the shipping box in the location where the system will be
installed, leaving it right side up on its shipping pallet.
2. Use the scissors or knife to cut the shipping straps and remove
them from the shipping box. To avoid injury while cutting each
strap, hold the strap firmly with one hand as you stand away
from it.
WARNING
!
To avoid eye or skin injuries, be careful when
cutting the straps from the box. The straps
can snap with considerable force when cut.

-5-
3. Open the top cardboard flaps of the shipping box by cutting
through the taped portion of the flaps to release them.
4. If you have received a pedestal system, remove the pedestal
case, place it on a table or other sturdy surface, and remove
its foam packaging material.
WARNING
!
To avoid back injury, lift and remove the
pedestal case with the assistance of another
person.
5. Remove the accessories box. Open the accessories box and
make sure that it contains (along with other items) the
Express5800/320Fc: Setup Guide.
6. Lift and remove the shipping box from the shipping pallet.
WARNING
!
To avoid back injury, do not attempt to remove
the shelf unit or enclosures before you
remove the shipping box from the shipping
pallet.
7. If you received a rack-mountable system, remove the shelf
unit and place it on a table or other sturdy surface and remove
its foam packaging material.

-6-
8. Remove each CPU-I/O enclosure, one at a time, from the
shipping pallet. Pull the foam blocks away from the first
enclosure and remove it. Then, do the same for the second
enclosure.
WARNING
!
To avoid back injury, lift and remove each
enclosure with the assistance of another
person.
9. Remove the enclosures from their plastic bags, then place the
enclosures flat on a table or other sturdy work surface near the
installation area.
Disposing of Packing Materials
The packing materials do not contain any hazardous compounds.
Dispose of them according to applicable procedures or local
regulations.
If, however, you decide to retain the undamaged container and its
packing materials, you can use them to ship the system at a later
time.
What to Do Next
To install the system, see the Express5800/320Fc: Setup Guide.