NEC Express5800/R120f-1E User manual

NEC Express5800/R120f-1E
System Configuration Guide
Introduction
This document contains product and configuration information that will enable you to configure your system. The guide will
ensure fast and proper configuration of your NEC Express5800 server.
July 16, 2015
Revision 6.0
NEC Corporation

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 2
Contents
TECHNICAL SPECIFICATION........................................................................................3
Key Features..........................................................................................................................................3
Specification..........................................................................................................................................3
EXTERNAL VIEWS .........................................................................................................7
Front and Rear Views ...........................................................................................................................7
Dimensions (mm)..................................................................................................................................8
CONFIGURATION DIAGRAM.........................................................................................9
Expansion Slots ....................................................................................................................................9
SERVER CONFIGURATION .........................................................................................10
1Base Models.................................................................................................................................10
2Processors and Heat Sink ..........................................................................................................10
3Memory .........................................................................................................................................11
3.1 Memory Configuration........................................................................................................11
3.2 Other than Windows server 2008 Standard ......................................................................11
3.3 Windows Server 2008 Standard........................................................................................12
4Internal Hard Disk Drives............................................................................................................14
4.1 RAID Configuration............................................................................................................14
4.2 Required Components for RAID Configuration .................................................................14
4.3 Supported Drives ...............................................................................................................16
5Optical Drive.................................................................................................................................19
6PCI Card........................................................................................................................................20
6.1 PCI Riser Card...................................................................................................................20
6.2 Network Interface Controller..............................................................................................20
6.3 InfiniBand...........................................................................................................................22
6.4 External Storage Controller ...............................................................................................22
6.5 Serial Port Adapter.............................................................................................................24
7Other Add-in Components..........................................................................................................24
7.1 Power Supply.....................................................................................................................24
7.2 Internal Flash Memory.......................................................................................................24
7.3Trusted Platform Module Kit ..............................................................................................24
7.4 Flash FDD..........................................................................................................................24
8Add-on Components ...................................................................................................................25
8.1 17-inch LCD Console Drawer............................................................................................25
8.2 KVM Switch........................................................................................................................25
8.3 Cable Management Arm....................................................................................................26
8.4 Server Management License.............................................................................................26
REFERENCES...............................................................................................................27
Boot Mode Setting ..............................................................................................................................27
Server Management............................................................................................................................28
OS Support Matrix for PCI Cards and Embedded Controllers .......................................................29
Supported PCI Cards and Installable Slots......................................................................................30
Copyright Notice and Liability Disclaimer........................................................................................33
REVISION HISTORY .....................................................................................................34

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 3
Technical Specification
Key Features
High performance with the latest Intel® Xeon® processor E5-2600 v3 Product Family
Up to 512 GB of high speed DDR4 memory
High energy efficiency with power capping feature and 80 PLUS® Platinum power supply
Full manageability by integrated EXPRESSSCOPE Engine 3
Specification
(1 / 2)
Model
R120f-1E
Processor
Type
Intel® Xeon®
processor
E5-2603 v3
Intel® Xeon®
processor
E5-2620 v3
Intel® Xeon®
processor
E5-2630 v3
Intel® Xeon®
processor
E5-2630L v3
Clock speed
1.60GHz
2.40 GHz
1.80 GHz
Number of Processors
1 or 2
Cache
15 MB
20 MB
Cores and Threads
6C-6T
6C-12T
8C-16T
Chipset
Intel® C612 Chipset
Memory
Type
DDR4-2133 Registered DIMM
DDR4-2133 Load Reduced DIMM
Standard Capacity
0 GB
Maximum Capacity
512 GB (16 x 32 GB)
Memory protection
ECC, x4 SDDC, Memory Mirroring, Memory Lockstep, Memory
Sparing
Internal Storage
Standard Capacity
0 GB
Maximum Capacity
SAS HDD : 14.4 TB (8 x 1.8 TB)
SATA HDD : 16 TB (8 x 2 TB)
SAS SSD : 3.2 TB ( 8 x 400 GB)
SATA SSD : 6.4 TB (8 x 800 GB)
Disk Controller
SATA : 6Gb/s (Integrated)
SAS: 12 Gb/s (Optional)
RAID
SATA : RAID 0/1/5/6/10/50/60 (Optional)
SAS : RAID 0/1/5/6/10/50/60 (Optional)
Hot Plug
Supported
Optical Disk Drive
Optional
Optical Drive Bays
1
Disk Drive Bays
8
Expansion Slots
Standard
Total: 3 slots available
1 PCIe 3.0 x8 (x8 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Optional Riser Card
(N8116-39)
Total: 4 slots available
2 PCIe 3.0 x8 (x8 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Optional Riser Card
(N8116-33)
Total: 4 slots available
2 PCIe 3.0 x16 (x16 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Video
Controller (VRAM)
Integrated in Server Management Controller (32MB)
Resolution / Color
1600 x 1200 / 16.7M 1

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 4
Model
R120f-1E
Interfaces
2 x VGA (15-pin mini D-sub, 1 x front, 1 x rear)
1 x Serial (9-pin mini D-sub, RS232-C, Serial A, 1 x rear)
4 x USB3.0 (2 x front, 2 x rear)
1 x Management LAN connector (RJ-45, 1 x rear)
Server Management
EXPRESSSCOPE Engine 3
Redundant Fan
Standard, non-hot plug
Redundant Power Supply
Optional, hot plug
Power Supply
1-2 x 460 Watt or 800 Watt 80 PLUS® Platinum certified hot plug
PSU, or 800 Watt 80 PLUS® Titanium certified hot plug PSU
100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz
Power
Consumption
(Max. Config, Idling)
193 VA
/ 191 Watt
192 VA
/ 191 Watt
186 VA
/ 184 Watt
188 VA
/ 187 Watt
(Max. Config,
Operating)
457 VA
/ 454 Watt
555 VA
/ 551 Watt
568 VA
/ 564 Watt
500 VA
/ 497Watt
Acoustical Noise
(Sound Pressure
Level)2
Max. Config, Idling
45.2 dB
45.2 dB
Max. Config, Operating
53.0 dB
52.0 dB
Dimensions (W x D x H )
439.8 x 722.0 x 43.4 mm / 17.3 x 28.4 x 1.7 in (1U)
Weight (Minimum / Maximum)
14.6 kg / 21.0 kg, 32.18 lbs. / 46.29 lbs.
Temperature, Relative Humidity
(non-condensing)
Operating: 10° to 40° C / 50° to 104° F, 20 to 80%
Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80%
Regulatory and Safety
FCC, UL, CB, CE, BSMI, UL(Mexico), KC, CCC, RCM, RoHS,
WEEE
Operating Systems
Microsoft® Windows Server® 2008 Standard (x86)
Microsoft® Windows Server® 2008 Enterprise (x86)
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 R2 Datacenter
Red Hat Enterprise Linux 6.5 or later (x86) 3
Red Hat Enterprise Linux 6.5 or later (x86_64) 3
Red Hat Enterprise Linux 7.1 or later 3
VMware ESXi™5.1 Update 2
VMware ESXi™5.5 Update 2
VMware ESXi™ 6.0
1Maximum resolution available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors.
2Noise emission was measured at the bystander positions in accordance with ISO 7779. The actual value may
vary by the operating environment.
3For Linux support, contact your sales representative or go to the NEC website at:
http://www.nec.com/global/prod/express/linux/index.html
(2 / 2)
Model
R120f-1E
Processor
Type
Intel® Xeon®
processor
E5-2640 v3
Intel® Xeon®
processor
E5-2650 v3
Intel® Xeon®
processor
E5-2650L v3
Intel® Xeon®
processor
E5-2660 v3
Clock speed
2.60 GHz
2.30 GHz
1.80 GHz
2.60 GHz
Number of Processors
1 or 2
Cache
20 GB
25 MB
30 MB
25 MB
Cores and Threads
8C-16T
10C-20T
12C-24T
10C-20T
Chipset
Intel® C612 Chipset

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 5
Model
R120f-1E
Memory
Type
DDR4-2133 Registered DIMM
DDR4-2133 Load Reduced DIMM
Standard Capacity
0 GB
Maximum Capacity
512 GB (16 x 32 GB)
Memory protection
ECC, x4 SDDC, Memory Mirroring, Memory Lockstep, Memory
Sparing
Internal Storage
Standard Capacity
0 GB
Maximum Capacity
SAS HDD : 14.4 TB (8 x 1.8 TB)
SATA HDD : 16 TB (8 x 2 TB)
SAS SSD : 3.2 TB ( 8 x 400 GB)
SATA SSD : 6.4 TB (8 x 800 GB)
Disk Controller
SATA : 6Gb/s (Integrated)
SAS: 12 Gb/s (Optional)
RAID
SATA : RAID 0/1/5/6/10/50/60 (Optional)
SAS : RAID 0/1/5/6/10/50/60 (Optional)
Hot Plug
Supported
Optical Disk Drive
Optional
Optical Drive Bays
1
Disk Drive Bays
8
Expansion Slots
Standard
Total: 3 slots available
1 PCIe 3.0 x8 (x8 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Optional Riser Card
(N8116-39)
Total: 4 slots available
2 PCIe 3.0 x8 (x8 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Optional Riser Card
(N8116-33)
Total: 4 slots available
2 PCIe 3.0 x16 (x16 connector)
1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot
1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot
Video
Controller (VRAM)
Integrated in Server Management Controller (32MB)
Resolution / Color
1600 x 1200 / 16.7M 1
Interfaces
2 x VGA (15-pin mini D-sub, 1 x front, 1 x rear)
1 x Serial (9-pin mini D-sub, RS232-C, Serial A, 1 x rear)
4 x USB3.0 (2 x front, 2 x rear)
1 x Management LAN connector (RJ-45, 1 x rear)
Server Management
EXPRESSSCOPE Engine 3
Redundant Fan
Standard, hot plug
Redundant Power Supply
Optional, hot plug
Power Supply
1-2 x 460 Watt or 800 Watt 80 PLUS® Platinum certified hot plug
PSU, or 800 Watt 80 PLUS® Titanium certified hot plug PSU
100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz
Power
Consumption
(Max. Config, Idling)
191 VA
/ 189 Watt
194 VA
/ 192 Watt
185 VA
/ 184 Watt
194 VA
/ 193 Watt
(Max. Config,
Operating)
602 VA
/ 598 Watt
649 VA
/ 645 Watt
540 VA
/ 537 Watt
658 VA
/ 653 Watt
Acoustical Noise
(Sound Pressure
Level) 3
Max. Config, Idling
45.2 dB
45.2 dB
45.2 dB
45.2 dB
Max. Config, Operating
53.8 dB
54.0 dB
55.3 dB
54.0 dB
Dimensions (W x D x H )
439.8 x 722.0 x 43.4 mm / 17.3 x 28.4 x 1.7 in (1U)
Weight (Minimum / Maximum)
14.6 kg / 21.0 kg, 32.18 lbs. / 46.29 lbs.
Temperature, Relative Humidity
(non-condensing)
Operating: 10° to 40° C / 50° to 104° F, 20 to 80%
Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80%
Regulatory and Safety
FCC, UL, CB, CE, BSMI, UL(Mexico), KC, CCC, RCM, RoHS,
WEEE

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 6
Model
R120f-1E
Operating Systems
Microsoft® Windows Server® 2008 Standard 3
Microsoft® Windows Server® 2008 Enterprise (x86) 3
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 R2 Datacenter
Red Hat Enterprise Linux 6.5 or later (x86) 4
Red Hat Enterprise Linux 6.5 or later (x86_64) 4
Red Hat Enterprise Linux 7.1 or later 4
VMware ESXi™5.1 Update 2
VMware ESXi™5.5 Update 2
VMware ESXi™6.0
1Maximum resolution available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors.
2Noise emission was measured at the bystander positions in accordance with ISO 7779. The actual value may
vary by the operating environment.
3Not supported on Xeon® processor E5-2650 v3, E5-2650L v3, and E5-2660 v3 systems.
4For Linux support, contact your sales representative or go to the NEC website at:
http://www.nec.com/global/prod/express/linux/index.html

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 7
External Views
Front and Rear Views
Front View
Legend
A.
2.5-inch Drive Bays
J.
Power Capping LED
B.
Optical Drive Bay
K.
Data LAN 1 Activity LED
C.
Power Button / Power LED
L.
Data LAN 2 Activity LED
D.
UID LED Button
M.
Data LAN 3 Activity LED
E.
System Reset Button
N.
Data LAN 4 Activity LED
F.
Dump (NMI) Button
O.
USB Connectors
G.
BMC Reset Button
P.
Display Connector
H.
System Status LED 1
Q.
Pull-out Tab
I.
System Status LED 2
Rear View
Legend
A.
PCI Slot (Full-Height)
G.
UID Button/LED
B.
PCI Slot (Low-Profile)
H.
Serial Port Connector
C.
Power Supply
I.
VGA Connector
D.
AC Inlet
J.
Management LAN Connector
E.
AC Power LED
K.
LOM Card Slot
F.
USB Connectors
L.
Additional Power Supply Slot
A
B
E
C
D
N
F
G
I
J
K
O
M
H
L
P
Q
A
B
C
D
F
G
I
J
K
E
L
H

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 8
Dimensions (mm)
Without Management Arm
With Cable Management Arm
816.0
722.044.1 32.1 43.4
44.1
482.4 439.8 479.7
947.5
905.3

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 9
Configuration Diagram
Legend: Standard Components Minimum required components
Expansion Slots
Legend
Remarks
Common
#1A
PCIe 3.0 x8, x8 connector, for a dedicated RAID controller
#1B
PCIe 3.0 x8, x8 connector, for a dedicated LOM Card
#1D
PCIe 3.0 x8, x8 connector, Low-profile, up to 220 mm length
PCIe x8
Riser
Card Kit
#1C
PCIe 3.0 x8, x8 connector, Full-height, up to 220 mm length
Optional Riser
PCIe x16
Riser
Card Kit
#1C
PCIe 3.0 x16, x16 connector, Full-height, up to 220 mm length
Required 2 CPU,
Optional Riser
#1D
PCIe 3.0 x16, x16 connector, Low-profile, up to 220/312 mm length
Optical Drive Bay
2.5-inch
Hot Plug
Drive Cage
CPU 2
4x DIMM Slots
4x DIMM Slots
4x DIMM Slots
4x DIMM Slots
Hot Plug
Power Supply 2
RAID Slot
PCIe 3.0
PCIe 3.0
2x RAID
FBU Slots
PCI Riser
Cooling Fan
1xDIMM
Cooling
Fan
(CPU2) Hot Plug
Power Supply 1
LOM
Card
CPU 1
6x 2.5-inch
Drives 2x 2.5-inch Drives
PSU
2
PSU
1#1C #1D LOM
Optical
Driver
Bay
CHASSIS
FRONT
CHASSIS
INSIDE
CHASSIS
REAR
Slot #1A
Slot #1B
Slot #1C
Slot #1D

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 10
Server Configuration
1 Base Models
Product Name / Description
Part Number
NEC Express5800/R120f-1E Server
no processor, no RAM, no HDD, no ODD, no LOM Card
Including : 1 x 460 Watt 80 PLUS® Platinum Power Supply Unit, Front Bezel, 2.5-inch
Drive Cage, EXPRESSBUILDER DVD
N8100-2249F
NEC Express5800/R120f-1E Server
no processor, no RAM, no HDD, no ODD, no LOM Card
Including : 1 x 800 Watt 80 PLUS® Platinum Power Supply Unit, Front Bezel, 2.5-inch
Drive Cage, EXPRESSBUILDER DVD
N8100-2250F
NEC Express5800/R120f-1E Server
no processor, no RAM, no HDD, no ODD, no LOM Card
Including : 1 x 800 Watt 80 PLUS® Titanium Power Supply Unit, Front Bezel, 2.5-inch
Drive Cage, EXPRESSBUILDER DVD
N8100-2251F
NOTE:
The base model must be ordered with a processor kit, a memory kit, and a LOM card.
Use the NEC Power Supply Selector to select appropriate size for power units. For details, please
visit the NEC website at:
http://www.nec.com/en/global/prod/express/collateral/tools/PowerSelector_G01.xls
2 Processors and Heat Sink
Available sockets: 2
Product Name / Description
Part Number
Processors
1 Processor
Required
Xeon E5-2603 v3 Processor Kit
Intel® Xeon ® Processor E5-2603 v3 (1.60 GHz, 6C/6T, 15 MB)
N8101-768F
Xeon E5-2620 v3 Processor Kit
Intel® Xeon ® Processor E5-2620 v3 (2.40 GHz, 6C/12T, 15 MB)
N8101-770F
Xeon E5-2630 v3 Processor Kit
Intel® Xeon ® Processor E5-2630 v3 (2.40 GHz, 8C/16T, 20 MB)
N8101-934F
Xeon E5-2630L v3 Processor Kit
Intel® Xeon ® Processor E5-2630L v3 (1.80 GHz, 8C/16T, 20 MB)
N8101-935F
Xeon E5-2640 v3 Processor Kit
Intel® Xeon ® Processor E5-2640 v3 (2.60 GHz, 8C/16T, 20 MB)
N8101-773F
Xeon E5-2650 v3 Processor Kit
Intel® Xeon ® Processor E5-2650 v3 (2.30 GHz, 10C/20T, 25 MB)
N8101-936F
Xeon E5-2650L v3 Processor Kit
Intel® Xeon ® Processor E5-2650L v3 (1.80 GHz, 12C/24T, 30 MB)
N8101-775F
Xeon E5-2660 v3 Processor Kit
Intel® Xeon ® Processor E5-2660 v3 (2.60 GHz, 10C/20T, 25 MB)
N8101-776F
Heat Sink
1st
Processor Heat Sink
For 1st Processor
(Standard)
2nd
Processor Heat Sink
For 2nd Processor, including cooling fan kit
N8101-901F
NOTE:
Minimum one processor kit from above must be installed.
The processors must be the same to configure dual processor system.
The 32-bit operating systems, Microsoft Windows Server 2008 and Red Hat Enterprise Linux 6 (x86),
are supported only on Xeon E5-2603 v3, E5-2620 v3, Xeon E5-2630 v3,.Xeon E5-2630L v3, and
Xeon E5-2640 v3 systems.

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 11
The maximum number of logical processors supported by OS
See the table below for the maximum number of logical processors that you can actually use on your
system.
Number of Logical Processors Supported by Operating Systems
Maximum Available
Number of logical
Processors
Microsoft Windows Server 2008 Standard (x86)
Microsoft Windows Server 2008 Enterprise (x86)
32 1
32
Microsoft Windows Server 2008 R2 Standard (x64)
Microsoft Windows Server 2008 R2 Enterprise (x64)
256 1
48
Microsoft Windows Server 2012 Standard
Microsoft Windows Server 2012 Datacenter
Microsoft Windows Server 2012 R2 Standard
Microsoft Windows Server 2012 R2 Datacenter
640 1
48
Red Hat Enterprise Linux 6
32
32
Red Hat Enterprise Linux 6 (x86_64)
Red Hat Enterprise Linux 7
240
48
VMware ESXi 5.1
160
48
VMware ESXi 5.5
320
48
VMware ESXi 6.0
480
48
1The maximum numbers of logical processors when using Hyper-V are below:
- Windows Server 2008 : 24
- Windows Server 2008 R2 : 64
- Windows Server 2012, Windows Server 2012 R2 : 320
3 Memory
3.1 Memory Configuration
Refer to the section in accordance with your operating system and memory configuration:
Other than Windows server 2008 Standard
Independent Channel Configuration: Refer to 3.2.1
Memory Sparing Configuration: Refer to 3.2.2
Memory Mirroring / Memory Lockstep Configuration: Refer to 3.2.3
Microsoft Windows 2008 Standard
Independent Channel Configuration: Refer to 3.3.1
3.2 Other than Windows server 2008 Standard
3.2.1 Independent Channel Configuration
Available slots: 8 per processor
Category
Product Name / Description
Part Number
Registered DIMM
(RDIMM)
4GB DDR4-2133 REG Memory Kit (1x4GB)
1 x 4GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-631F
8GB DDR4-2133 REG Memory Kit (1x8GB)
1 x 8GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-632F
16GB DDR4-2133 REG Memory Kit (1x16GB)
1 x 16GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-633F
Load Reduced DIMM
(LRDIMM)
32GB DDR4-2133 LR Memory Kit (1x32GB)
1 x 32GB Load Reduced ECC DIMM, DDR4-2133(PC4-2133)
N8102-634F
NOTE:

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 12
Minimum one memory kit per processor must be installed.
It is recommended to install memory kits in multiples of two (four identical DIMMs) for quad-channel
symmetric memory configurations to increase memory transfer speed.
When two processors are installed, balance the DIMMs across the two processors.
Mix configurations of RDIMM and LRDIMM are not supported.
At least 5 GB of memory is required for VMware ESXi™ 5.5 and VMware ESXi™6.0
3.2.2 Memory Sparing Configuration
Available slots: 8 per processor
Product Name / Description
Part Number
32GB DDR4-2133 REG Memory Kit (2x16GB)
2 x 16GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-642
NOTE:
Minimum one memory kit per processor must be installed.
The configured memories must be identical.
When two processors are installed, balance the DIMMs across the two processors.
The logical memory capacity at the time of memory sparing becomes five-sixth physical capacity with
configurations more than 16GB DIMM.
3.2.3 Memory Mirroring / Memory Lockstep Configuration
Available slots: 8 per processor
Product Name / Description
Part Number
16GB DDR4-2133 REG Memory Kit (2x8GB)
2 x 8GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-637
32GB DDR4-2133 REG Memory Kit (2x16GB)
2 x 16GB Registered ECC DIMM, DDR4-2133 (PC4-2133)
N8102-638
NOTE:
Minimum one memory kit per processor must be installed.
The logical memory capacity at the time of memory mirroring becomes a half of physical capacity.
3.3 Windows Server 2008 Standard
3.3.1 Independent Channel Configuration
Available slots: 1
Product Name / Description
Part Number
4GB DDR4-2133 REG Memory Kit (1x4GB)
1 x 4GB Registered ECC DIMM, DDR4-2133(PC4-2133)
N8102-631F
NOTE:
Only one Memory Kit can be installed regardless of the number of processors.
Memory Configuration Feature Comparison
See the table below for feature comparisons of memory configurations supported.
Independent
Channel
Memory
Sparing
Memory
Lockstep
Memory
Mirroring
Performance
Best
Better
Better
Good
Data Protection
No
Multiple single bit
error protection
No
Multiple single bit
and multi bit error
protection

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 13
Redundancy
No
Partly
No
Fully
Data Correction
ECC, x4 SDDC
ECC, x4 SDDC
ECC, x8 SDDC
ECC, x4 SDDC
Available Memory
Full physical
memory
3/4 physical memory
(16GB DIMM)
Full physical
memory
Half physical
memory
Available Memory
Channels
4
4
4
4
Notes
-
All DIMMs in the
system must be
identical.
Paired DIMMs must
be identical.
Paired DIMMs must
be identical.
Maximum Memory Speed
See the table below for the actual maximum memory transfer speed in Independent Channel / Memory
Sparing Configuration.
DDR4 memory speed depends on the type of DIMMs, the native memory bus speed of the memory
controller and memory configuration. All memory buses operate at the clock frequency of the DIMM with
the lowest frequency.
Processor Type
Populated DIMMs
# of DIMMs per processor
DIMM Speed
E5-2603 v3
RDIMM: 4, 8, 16 GB
LRDIMM: 32GB
-
1600 MHz
E5-2620 v3
E5-2630 v3
E5-2630L v3
E5-2640 v3
RDIMM: 4, 8, 16 GB
LRDIMM: 32GB
-
1866 MHz
E5-2650 v3
E5-2650L v3
E5-2660 v3
RDIMM: 2, 4, 8, 16 GB
LRDIMM: 32GB
-
2133 MHz
Maximum Available Memory
See the table below for the maximum memory size that you can actually use on your system.
The maximum available memory is less than the maximum physical memory supported by your system
because some chipsets require PCI resource space of about 750MB. PCI resource requirements vary
depending on the type and the number of PCI cards you are using.
Maximum Memory Size Supported by Operating Systems
Maximum Available Memory
Microsoft Windows Server 2008 Standard (x86) 1
4 GB
4 GB (HW-DEP enabled)
App. 2 GB(HW-DEP disabled)
Microsoft Windows Server 2008 R2 Standard 1
32 GB
32 GB
Microsoft Windows Server 2008 Enterprise (x86) 1
64 GB
64 GB
Microsoft Windows Server 2008 R2 Enterprise 1
2 TB
512 GB
Microsoft Windows Server 2012 Standard 1
Microsoft Windows Server 2012 Datacenter 1
Microsoft Windows Server 2012 R2 Standard 1
Microsoft Windows Server 2012 R2 Datacenter 1
4 TB
512 GB
Red Hat Enterprise Linux 6
16 GB
16 GB
Red Hat Enterprise Linux 6 (x86_64)
Red Hat Enterprise Linux 7
6 TB
512 GB
VMware ESXi 5.1 2
2 TB
512 GB
VMware ESXi 5.5 2
4 TB
512 GB
VMware ESXi 6.0 3
6 TB
512 GB
1The maximum available memory size of Hyper-V systems are below:
- Windows Server 2008 R2 Standard : 32 GB
- Windows Server 2008 R2 Enterprise : 1 TB
- Windows Server 2012, Windows Server 2012 R2 : 4 TB
2Up to 1TB of main memory is available to each virtual machine.

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 14
3Up to 4TB of main memory is available to each virtual machine.
4 Internal Hard Disk Drives
4.1 RAID Configuration
Refer to the section in accordance with your OS and RAID configuration. For example, when you would like
to configure RAID 0/1/10 1GB cache with Windows Server 2012 R2, refer to the section 4.2.3 for the
required components and then refer to the section 4.3.4 for the hard drives.
Operating System
Supported RAID configuration
Supported
HDD/SSD
RAID and Cache
Section
Windows Server 2008 Standard
Windows Server 2008 Enterprise
Windows Server 2008 R2 Standard
Windows Server 2008 R2 Enterprise
Red Hat Enterprise Linux 6
KVM in Red Hat Enterprise Linux 6
(x86_64)
Non-RAID (Embedded SATA)
4.2.1
4.3.1
RAID 0/1 (Embedded SATA RAID)
4.2.2
4.3.2
RAID 0/1/10 1GB Cache
4.2.3
4.3.3
RAID 5/6/50/60 1GB Cache
4.2.4
RAID 5/6/50/60 2GB Cache
4.2.5
Windows Server 2012 Standard
Windows Server 2012 Datacenter
Windows Server 2012 R2 Standard
Windows Server 2012 R2 Datacenter
Red Hat Enterprise Linux 6 (x86_64)
without KVM feature
Red Hat Enterprise Linux 7
Non-RAID (Embedde SATA)
4.2.1
4.3.1
RAID 0/1 (Embedded SATA RAID)
4.2.2
4.3.2
RAID 0/1/10 1GB Cache
4.2.3
4.3.4
RAID 5/6/50/60 1GB Cache
4.2.4
RAID 5/6/50/60 2GB Cache
4.2.5
VMware ESXi
Non-RAID (Embedded SATA)
4.2.1
4.3.1
RAID 0/1/10 1GB Cache
4.2.3
4.3.3
RAID 5/6/50/60 1GB Cache
4.2.4
RAID 5/6/50/60 2GB Cache
4.2.5
NOTE:
Up to four hard drives can be installed in the Embedded SATA configuration.
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATA HDDs, SAS SSDs
and SATA SSDs can be mixed in each drive cage.
It is recommended to set RAID array configuration drives less than eight per disk group in order to
minimize the risk of becoming multiple hard drives failure.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
4.2 Required Components for RAID Configuration
4.2.1 Up to four Drives with embedded SATA Controller
Category
Product Name / Description
Part Number
Storage Controller
Embedded SATA Controller
4 x 6Gb/s SATA
(Standard)
Cable
Internal SATA Cable
1 x mini-SAS HD to 1 x mini-SAS HD, 1 set
(Standard)
Drive Cage
2.5-inch Drive Cage
8 x 2.5-inch Hot-plug hard drive bays
(Standard)
NOTE:
Up to 4 SATA drives are supported.
For supported HDD, refer to 4.3.1
Hot plug insertion/removal are not supported in the configuration.

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 15
4.2.2 Up to four Drives with embedded SATA RAID Controller
Category
Product Name / Description
Part Number
Storage Controller
Embedded SATA Controller
4 x 6Gb/s SATA
(Standard)
Cable
Internal SATA Cable
1 x mini-SAS HD to 1 x mini-SAS HD, 1 set
(Standard)
Drive Cage
2.5-inch Drive Cage
8 x 2.5-inch Hot-plug hard drive bays
(Standard)
NOTE:
Supported up to 4x SATA HDD.
For supported HDD, refer to 4.3.2
4.2.3 RAID 0/1 Controller with 1 GB Cache
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (1GB, RAID 0/1)
LSI MegaRAID SAS 9362-8i
RAID 0/1/10, 1GB, Int. 8, PCIe 3.0 x8, 12Gb/s
N8103-176
Flash Backup
Recommended
Flash Backup Unit
for LSI MegaRAID SAS 9362-8i
650mm Cable for Flash Backup Unit included
N8103-181
Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
(Standard)
Optional Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
NOTE: To install five drives or more, optional cable is
required.
K410-324(00)
Drive Cage
2.5-inch Drive Cage
8 x 2.5-inch hot plug drive bays
(Standard)
NOTE:
For Supported HDD/SSD, refer to 4.3.3 for Windows Server 2008/2008R2, Red Hat Enterprise Linux
6, Red Hat Enterprise Linux 6(x86_64) with KVM feature, or VMware. Refer to 4.3.4 for Windows
Server 2012/2012R2, Red Hat Enterprise Linux 6(x86_64) without KVM feature, or Red Hat
Enterprise Linux 7.
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATAHDDs, SATASSD and
SAS SSDs can be mixed.
4.2.4 RAID 5/6 Controller with 1 GB Cache
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (1GB, RAID 0/1/5/6)
LSI MegaRAID SAS 9362-8i
RAID0/1/5/6/10/50/60, 1GB, Int. 8, PCIe 3.0 x8, SAS 12Gb/s,
SATA 6Gb/s
N8103-177
Flash Backup
Recommended
Flash Backup Unit
for LSI MegaRAID SAS 9362-8i
650mm Cable for Flash Backup Unit included
N8103-181
Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
(Standard)
Optional Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
NOTE: To install five drives or more, optional cable is
required.
K410-324(00)

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 16
Drive Cage
2.5-inch Drive Cage
8 x 2.5-inch hot plug drive bays
(Standard)
NOTE:
For Supported HDD/SSD, refer to 4.3.3 for Windows Server 2008/2008R2, Red Hat Enterprise Linux
6, Red Hat Enterprise Linux 6(x86_64) with KVM feature, or VMware. Refer to 4.3.4 for Windows
Server 2012/2012R2, Red Hat Enterprise Linux 6(x86_64) without KVM feature, or Red Hat
Enterprise Linux 7.
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATAHDDs, SATASSD and
SAS SSDs can be mixed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
4.2.5 RAID 5/6 Controller with 2 GB Cache
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (2GB, RAID 0/1/5/6)
LSI MegaRAID SAS 9362-8i
RAID0/1/5/6/10/50/60, 2GB, Int. 8, PCIe 3.0 x8, 12Gb/s
N8103-178
Flash Backup
Recommended
Flash Backup Unit
for LSI MegaRAID SAS 9362-8i
650mm Cable for Flash Backup Unit included
N8103-181
Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
(Standard)
Optional Cable
Internal SAS/SATA Cable
1 x Mini SAS HD to 1 x Mini SAS HD, 1 set
NOTE: To install five drives or more, optional cable is
required.
K410-324(00)
Drive Cage
2.5-inch Drive Cage
8 x 2.5-inch hot plug drive bays
(Standard)
NOTE:
For Supported HDD/SSD, refer to 4.3.3 for Windows Server 2008/2008R2, Red Hat Enterprise Linux
6, Red Hat Enterprise Linux 6(x86_64) with KVM feature, or VMware. Refer to 4.3.4 for Windows
Server 2012/2012R2, Red Hat Enterprise Linux 6(x86_64) without KVM feature, or Red Hat
Enterprise Linux 7.
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATAHDDs, SATASSD and
SAS SSDs can be mixed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
4.3 Supported Drives
4.3.1 For Embedded SATA Controller
Category
Product Name / Description
Part Number
Drive
4 slots
available
SATA
HDD
250GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-487
500GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-488
1TB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-489
NOTE:
Hot plug insertion/removal are not supported in the configuration.

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 17
4.3.2 For Embedded SATA RAID Controller
Category
Product Name / Description
Part Number
Drive
4 slots
available
SATA
HDD
250GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-487
500GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-488
1TB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-489
4.3.3 For RAID Controller Configuration (1)
For Windows Server 2008/2008R2, Red Hat Enterprise Linux 6, KVM in Red Hat Enterprise Linux
6(x86_64), or VMware
Category
Product Name / Description
Part Number
Drive
8 slots
available
SAS
HDD
300GB 10K Hot Plug 2.5-inch SAS HDD
1 x 300 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-479
450GB 10K Hot Plug 2.5-inch SAS HDD
1 x 450 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-480
600GB 10K Hot Plug 2.5-inch SAS HDD
1 x 600 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-481
900GB 10K Hot Plug 2.5-inch SAS HDD
1 x 900 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-482
1.2TB 10K Hot Plug 2.5-inch SAS HDD
1 x 1.2TB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-483
300GB 15K Hot Plug 2.5-inch SAS HDD
1 x 300 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-485
450GB 15K Hot Plug 2.5-inch SAS HDD
1 x 450 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-486
600GB 15K Hot Plug 2.5-inch SAS HDD
1 x 600 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-518
SATA
HDD
250GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-487
500GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-488
1TB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-489
SAS
SSD
200GB Hot Plug 2.5-inch SAS SSD
1 x 200 GB SAS SSD, eMLC, 2.5-inch, 12Gb/s,
512B sector
N8150-721
400GB Hot Plug 2.5-inch SAS SSD
1 x 400 GB SAS SSD, eMLC, 2.5-inch, 12Gb/s,
512B sector
N8150-722

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 18
SATA
SSD
200GB Hot Plug 2.5-inch SATA SSD
1 x 200 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-725
400GB Hot Plug 2.5-inch SATA SSD
1 x 400 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-726
800GB Hot Plug 2.5-inch SATA SSD
1 x 800 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-727
NOTE:
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATA HDDs, SATA SSDs
and SAS SSDs can be mixed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
4.3.4 For RAID Controller Configuration (2)
For Windows Server 2012/2012R2, Red Hat Enterprise Linux 6(x86_64) without KVM, or Red Hat
Enterprise Linux 7
Category
Product Name / Description
Part Number
Drive
8 slots
available
SAS
HDD
(512B)
300GB 10K Hot Plug 2.5-inch SAS HDD
1 x 300 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-479
450GB 10K Hot Plug 2.5-inch SAS HDD
1 x 450 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-480
600GB 10K Hot Plug 2.5-inch SAS HDD
1 x 600 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-481
900GB 10K Hot Plug 2.5-inch SAS HDD
1x 900 GB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-482
1.2TB 10K Hot Plug 2.5-inch SAS HDD
1 x 1.2TB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
512B sector
N8150-483
300GB 15K Hot Plug 2.5-inch SAS HDD
1x 300 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-485
450GB 15K Hot Plug 2.5-inch SAS HDD
1x 450 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-486
600GB 15K Hot Plug 2.5-inch SAS HDD
1x 600 GB SAS HDD, 2.5-inch, 12Gb/s, 15,000 rpm,
512B sector
N8150-518
SAS
HDD
(4KB)
1.8TB 10K Hot Plug 2.5-inch SAS HDD
1 x 1.8TB SAS HDD, 2.5-inch, 12Gb/s, 10,000 rpm,
4KB sector
N8150-490
SATA
HDD
(512B)
250GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-487
500GB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-488
1TB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
512B sector
N8150-489

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 19
SATA
HDD
(4KB)
2TB 7.2K Hot Plug 2.5-inch SATA HDD
1 x 2 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm,
4KB sector
N8150-521
SAS
SSD
200GB Hot Plug 2.5-inch SAS SSD
1 x 200 GB SAS SSD, eMLC, 2.5-inch, 12Gb/s,
512B sector
N8150-721
400GB Hot Plug 2.5-inch SAS SSD
1 x 400 GB SAS SSD, eMLC, 2.5-inch, 12Gb/s,
512B sector
N8150-722
SATA
SSD
200GB Hot Plug 2.5-inch SATA SSD
1 x 200 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-725
400GB Hot Plug 2.5-inch SATA SSD
1 x 400 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-726
800GB Hot Plug 2.5-inch SATA SSD
1 x 800 GB SATA SSD, MLC, 2.5-inch, 6b/s,
512B sector
N8150-727
NOTE:
All drives within a RAID array should be of the same type, capacity and rotation speed.
Up to two kinds of drives selected from SAS 10K HDDs, SAS 15K HDDs, SATA HDDs, SATA SSDs
and SAS SSDs can be mixed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
The 4KB sector drives are make-to-order products. Please consult your sales representative in regard
to production lead time.
When you select 4KB sector HDD, confirm whether your applications support hard drives with 4 KB
sector size. For more information, visit the NEC website at:
http://www.nec.com/en/global/prod/express/svropt/hdd/collateral/4KHDD_Precautions_EN.pdf
Mix configurations of 4KB sector HDDs and 512B sector HDDs are not supported.
5 Optical Drive
Category
Product Name / Description
Part Number
Internal
1 slot available
Internal Slim DVD-ROM drive
Slim DVD-ROM drive
N8151-123
Internal DVD-SuperMulti Drive
Slim DVD Super Multi drive, not including writing software
N8151-124F
External
External DVD-ROM drive
DVD-ROM drive, Bus powered, 1.2 A required
N8160-91
NOTE:
Up to 1 optical drive can be connected.

SYSTEM CONFIGURATION GUIDE –NEC Express5800R120f-1E
NEC Corporation Revision 6.0 –July 16, 2015 20
6 PCI Card
Please refer to Supported PCI Cards and Installable Slots with regard to the position of PCI slot which
can mount PCI card supported.
6.1 PCI Riser Card
Product Name / Description
Part Number
PCIe Riser Card Kit
3 x PCIe 3.0 x8
(Standard)
PCIe x8 Riser Card Kit
4 x PCIe 3.0 x8
N8116-39
PCIe x16 Riser Card Kit
2 x PCIe 3.0 x16, 2 x PCIe 3.0 x8
N8116-33
NOTE:
N8116-33 PCIe x16 Riser Card Kit is supported in dual-processor configuration.
6.2 Network Interface Controller
Category
Product Name / Description
Part Number
LOM Card
1GbE
Quad Port 1000BASE-T LOM Card
Broadcom® BCM5719
PCIe 2.0 x4
N8104-154F
10GbE
Dual Port 10GBASE-T LOM Card
Intel Ethernet Controller X540
PCIe 2.0(x8)
N8104-155F
Dual Port 10G-SFP + Dual Port 1000BASE-T LOM Card
Qlogic NetXtreme II BCM57800S
PCIe 2.0 x8
NOTE:
- N8104-129 SFP+ Module is required to connect with an
optical cable.
- Up to two SFP+ Modules can be installed.
N8104-156F
Adapter
1GbE
1000BASE-T Adapter
Broadcom ® BCM5718 Gigabit Ethernet Controller
PCIe 2.0 x1
N8104-150
Dual Port 1000BASE-T Adapter
Broadcom ® BCM5718 Gigabit Ethernet Controller
PCIe 2.0 x1
N8104-151
Dual Port 1000BASE-T Adapter
Intel® 82580 Gigabit Ethernet Controller
PCIe 2.0 x4
NOTE:
- PXE boot is not supported on UEFI environment.
N8104-145
Quad Port 1000BASE-T Adapter
Broadcom ® BCM5719 Gigabit Ethernet Controller
PCIe 2.0 x4
NOTE:
- Network cables with RJ-45 plug covers cannot be used.
N8104-152
10GbE
Dual Port 10GBASE SFP+ Adapter (SFP+/2ch)
Intel 82599ES 10 Gigabit Ethernet Controller
PCIe 2.0 x8, Low Profile / Full Height
NOTE:
- N8104-129 SFP+ Module is required to connect with an
optical cable.
- Up to 2 SFP+ Modules can be installed.
N8104-148