NeckDoctor For DESK User manual

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
defective parts. Improper installation may cause damage or serious injury. Do not use this product
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use. INSTRUCTION MANUAL
The Original Ergonomic Single Monitor Arm
Product : NeckDoctor for DESK
Color : Metallic Grey
13”-32”
LCD/LED Curved
Monitors
VESA
Compatible
75x75 100x100
Weight Capacity
Curved/
LCD/LED
1~9kg
(2.2lbs~19.8lbs)
Screen Requirements

2
TOOL you will need
20lbs
(9.07kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Screwdriver
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
VESA Plate
C(x1)
Clamp Base
Support
J (x1)
Knob
NOTE:NOT ALL HARDWARE INCLUDED WILL BE USED
F (x1)
Long Screw
G(x5)
Bolt
H (x1)
Base Support
I (x1)
Support Plate
M-C (x4)
D5 Washer
WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
•
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
•
USE TIPOVER RESTRAINT
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
3
ASSEMBLY STEPS
STEP 1
OPTION A: CLAMP INSTALLATIONS
Install clamp base support (C) onto base of monitor
stand (A) with bolts (G) using provided 4mm Allen
wrench (L) . Apply pads (K) to bottom of base. Secure
clamp (D) to upper two holes with bolts(G) using
4mm Allen wrench(L) for desks with a thickness of
10-55mm. Secure clamp (D) to lower two holes with
bolts (G) using 4mm Allen wrench(L) for desks with a
thickness of 50-85mm. Attach base support cover (E)
to clamp base support (C) . Tighten the clamp to the
desktop using the plastic knob.
A
CL
G
K
10-55mm
D
LG
50-85mm
LG
E
K (x2)
Pad
M-A (x4)
M4x12
M-B(x4)
M5x12
L(1)
4mm Allen
Wrench
M (x1)
5mm Allen
Wrench
D(x1)
Clamp
E(x1)
Cable Clip

4 5
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide long screw (F) through the top of the grommet base support(H) and install on base of monitor
stand with bolts (G) using 4mm Allen wrench(L) . Apply pads (K) to bottom of base. Position stand on
desk with long screw through hole, and secure by using the support plate(I) and clamp knob (J) on
underside of the mounting surface.
STEP 2
Position VESA plate (B) on back of monitor and secure with screws (M-A) or (M-B) with (M-C) washers.
STEP 3
Pull back latch on monitor arm, and slide monitor
into place.
STEP 4
If needed, adjust the bolt on the side of the hinge
behind the VESA plate to tighten or loosen the tilt
angle support. Adjust gas spring tension by turning
screw with 6mm Allen wrench(M) . Clockwise
reduces tension, counter-clockwise increases
tension. The tension should be just enough to
NOTE: Tighten the socket set screw on the top of the
gas spring adjustment screw if the joints are making
a popping sound.
L
F
H
G
K
J
I
M- A
M- B
M- C
B
2
1
2
M
M

6 7
STEP 5
Remove cable covers as shown from upper and lower arms.
STEP 7
Store tools in base support cover (E) if clamp option is used.
1
2
1
STEP 6
Replace covers making sure the cables have enough slack to allow free movement of the arm.
1
2
1
180°
180°
+90°
-90°
270°
360°
L
M