NeckDoctor For WALL User manual

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
defective parts. Improper installation may cause damage or serious injury. Do not use this product
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use. INSTRUCTION MANUAL
The Original Ergonomic Single Monitor Arm
Product : NeckDoctor for WALL
Color : Matt Black

2 3
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Wall
Using the wall plate on the arm (A), mark
recommended. Drill 2.2” (55mm) deep holes
using a 3/16” (4.5mm) drill bit, and mount the
arm to the wall using screws (W-A) and washers
(W-C).
PACKAGE CONTENTS
Screwdriver
A (x1)
Arm
B(x1)
VESA Plate
C(x1)
VESA
Extension
M-F (x4)
D5 Washer
M-G (x8)
D8 Washer
W-A (x3)
Bolt
M-E(x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
M-D (x4)
M8x30
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x3)
Washer
W-B (x3)
Anchor
OPTION B: Concrete Wall
Using the wall plate on the arm (A), mark drilling
locations. Drill 2.4” (60mm) deep holes using a
3/8” (10mm) drill bit, press anchors (W-B) into
holes, and mount the arm to the wall using screws
(W-A) and washers (W-C) . NOTE: Anchors are
made for use with concrete or brick, and will not
work with drywall.
D(x1)
Screw Cover
E(x1)
Screw Cover
F (x4)
Nut
G(x4)
Carriage Bolt
STEP 2
H(x1)
Wrench
I(x1)
4mm Allen Wrench
J(x1)
6mm Allen
Wrench
M-H (x8)
Small Spacer
M-I (x8)
Large Spacer
Attach screw covers (D, E) to wall plate.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
50.6 lbs
(22.95kg)
Drill
D
E

4 5
STEP 3
Remove lower nut from VESA plate (B) using the wrench(H) , and loosen the upper two nuts until 3mm
of screw thread is exposed for each one.
STEP 5
OPTION A: Flat Back Monitor
Mount VESA plate(B) to TV using bolts (M-A or M-B) with washers (M-F or M-G) , making sure the two
nuts are facing towards the top of the TV.
STEP 4
Mount VESA extensions(C) to VESA plate (B) in one of the patterns shown using carriage bolts (G) and
nuts (F) , and tighten with the wrench.
(NOTE: For VESA patterns 200x200mm and smaller, skip this step.)
OPTION B: Curved Back Monitor
Mount VESA plate(B) to TV using bolts (M-C, M-D, M-E) with washers (M-G) and spacers (M-H, M-I) in
STEP 6
Hang TV with VESA plate onto head of arm(A).
H

6 7
STEP 7 STEP 9
Adjust gas spring tension using the 6mm Allen wrench(J)
clockwise to decrease. Adjust the tilt joint support using the 4mm Allen wrench(I) . NOTE: use a large
STEP 8
Reinstall lower nut to secure the plate, and tighten all nuts using the wrench.
Adjust as Desired
Use built in cable clips to manage cables.