Nemaura Pharma MIBOKO User manual

Quick Start Guide
Welcome to
Miboko®What is in your
Device Box?
Docking Station - Used to charge the Transmitter
Transmitter - Front View
Transmitter - Back View
Contact Slot
Arm Slots
Loop
Gold Contacts
Miboko®
Our mission is to make sure you can look and feel
the way you want to in everyday life and stay safe
from serious health issues, both now and in the future.
Your journey starts right here. With Miboko®you can
learn how to give your body what it needs to live
the life you want today and secure the health you need
tomorrow.
This Quick Start Guide takes you through the contents of the
Device and Sensor Kit Boxes and shows you the simple process
of getting started with your device.
It would help if you kept your Quick Start Guide somewhere
safe, as you may need to refer to them in the future. Please
read through all of the Quick Start Guide steps carefully
before applying your Transmitter, starting with charging the
Transmitter for up to 6 hours before use.
All of the contents provided are important for getting the most
out of your device. They will help you align all of the important
parts of your Sensor and Transmitter and ensure that your
device is securely in place. Your glucose readings are just a
few steps away!
Transmitter Password Card
Serial No.
Transmitter ID:
Password:
Transmitter/ Password Card - Contains the Transmitter Number
and case sensitive Password
Starting out with Miboko®
What is in your
Sensor Kit Box?
Sensor Kit - Supplied in a foil pouch which includes a
Sensor & Guiding Frame
Sensor - Detects the glucose in the interstitial fluid
Guiding Frame - To help accurately position the
Sensor on to your arm
12
Press
Press
B
A
Upper Backing Layer
Lower Backing Layer
Clip
Arms
Sensor Contacts
Sensing
Area
Fabric
Tab
Foam
Tab
Note: Do not open the Sensor and Guiding Frame pouch
until the Transmitter is fully charged and you are ready
to use your device.
What is in your
Sensor Kit Box? (Cont.)
Hydrogel Disc - Collects glucose from the skin, during wear
Hydrogel Disc - Supplied in a foil pouch on a single folded
plastic liner.
Hydrogel Disc
Plastic Liner Tab
Note: Do not open the Hydrogel pouch until the Transmitter
is fully charged and you are ready to use your device.
Charge The
Transmitter Connect To The App
1. Place the Transmitter
onto the Docking Station
with the three gold
contacts facing down and
close the lid.
Connect the Docking
Station to the power
supply.
2. Charge the Transmitter
fully before use. This can
take up to 6 hours.
The GREEN LIGHT
indicates that the Docking
Station has a power
connection, and the
AMBER LIGHT indicates
that the Transmitter is
charging. The amber
light will turn o when
the Transmitter is fully
charged.
3. Once charging is
complete, remove the
Transmitter.
1 2
1. To connect your Transmitter
to the App, tap ‘Find your
device’.
2. If the location and
Bluetooth permission windows
appear (depends on the phone
used), you must tap the OK
option to enable the App
connection to the Transmitter.
3. The App will scan for
Transmitters within range.
The number for your device
will be on the Transmitter /
password card. Tap on your
Transmitter.
4. When prompted, enter the
password located on the card
supplied with the device. The
password is case sensitive.
Find your device
Remember that you need to have
Bluetooth enabled to connect to devices
Searching for your device...
miboko.com

Skin Preparation Skin Preparation
(cont.)
12
Press
Press
B
A
B
12
Press
Press
1. Remove the Sensor
and Guiding Frame from
the foil pouch and put the
Sensor to one side as you
will need this in step 6.
2. Select a clean, ‘flat’
and dry area of the outer
side of the upper arm.
If necessary, clean the area
with an alcohol wipe.
3. Remove the Upper
Backing Layer from the
Guiding Frame. Firmly
press the Guiding Frame
onto your skin for 5
seconds.
43 Attach The Sensor Apply The
Hydrogel Disc
1.
2.
1.
2.
3. Push the Clip down
towards the Loop to
secure it in place on the
Transmitter. Stop when
you hear the click.
Be careful not to touch
the Sensing Area.
1. Gently fold back the
Foam Tab to expose the
Sensor Contacts.
Be careful not to touch
the Sensing Area.
2. Gently insert the
Sensor Contacts into
the Contact Slot on the
Transmitter until they
cannot go any further.
Ensure the Arms are fully
in the Transmitter Arm
Slots.
Note: Do not remove the
adhesive backing layer.
Sensing Area
4. Now remove the Lower
Backing Layer from the
Guiding Frame and firmly
press for an additional
5 seconds.
5. Press and roll your
thumb or finger over the
area marked ‘Press 1’,
for 10 seconds.
Repeat for ‘Press 2’ for
a further 10 seconds.
6. Peel o the part of the
Guiding Frame labelled A.
Note: Ensure the outer part
B, remains attached to the
arm.
7. Now take the Sensor that
you set aside in step 4.
5 6
12
Press
Press
A
B
12
Press
Press
B
A
12
Press
Press
Apply The Hydrogel
Disc (cont.) Attach To The Body
B
1. Carefully pick up your
Transmitter avoiding the
sticky surface.
Place the Transmitter into
the Guiding Frame aligning
the Loop with the arrow on
the Guiding Frame.
Press the Transmitter down
at both the top and sides
for 20 seconds, to firmly
secure the Transmitter.
Note: Take your time
with this step as it is not
recommended to remove
the Transmitter to realign
it once it is stuck.
2. Peel away the
remaining part of the
Guiding Frame labelled ‘B’
to completely remove it.
Lightly press on the edges
of the adhesive patch
to ensure it is securely
attached to the skin.
7 8
In the unlikely event that you experience some skin sensitivity
such as mild erythema or redness, the symptoms should
disappear within 1 day.
These symptoms can be minimised by:
(1) Alternating application sites.
(2) Keeping your skin clean when your device is not being worn.
(3) Avoiding scratching your skin.
DECLARATION: There is no known hazard to the patient from
the material used in Miboko®and it does not contain natural
latex rubber.
Nemaura Pharma Ltd.
Advanced Technology Innovation Centre
5 Oakwood Drive
Loughborough
LE11 3QF
United Kingdom
2797
Sensor Disposal9
2. Remove the Sensor
by unclipping it from the
Transmitter.
3. The Sensor should be
disposed of as general
non-clinical waste.
1. Remove any dirt
and moisture from the
Transmitter, by wiping with
a damp cloth.
1. At the end of the day
or if you have reached
the end of the 14-hour
wear time, remove the
Transmitter by gently
pulling the Fabric Tab away
from your skin.
Each Sensor should only
be used once.
Store The Transmitter
3. Recharge your Transmitter
before use.
2. Store the Transmitter in
the box or somewhere secure
and away from moisture or
excessive dust.
Remove the Arms from
the Arm Slots on the side
of the Transmitter.
10
Arrow
Loop
1. Remove the Hydrogel
Disc from its pouch,
holding only the curved
Plastic Liner Tab.
(Note: Pouch contains
water. Keep upright.)
2. Carefully unfold the
Plastic Liner to expose the
Hydrogel Disc inside.
Ensure you do not touch
the Hydrogel Disc.
3. Holding the Plastic Liner
Tab, place the Hydrogel
Disc over the centre of the
Sensing Area. Press down
on the Plastic Liner applying
slight pressure over the
Hydrogel Disc.
Manufacturer12
Further information
13
For further information including warnings,
precautions and troubleshooting.
NEM070 - 108-Rev01A
Date Prepared: Jan 2022
All images are for illustration
purposes only.
Skin Care Tips11
5. Firmly holding the
Fabric tab in place, peel
back the Foam tab from
the Sensor to expose the
adhesive, ensuring not to
touch the Hydrogel Disc.
The Fabric Tab should
remain on the Transmitter.
4. Continue to press
down whilst peeling the
Plastic Liner away in a
rolling motion, leaving
the Hydrogel Disc in place
on the Sensing Area.
Foam
tab
Fabric
tab