Neptronic TFL24 User manual

Networkable Fan Coil Controller
Specification and Installation Instructions
EFCB1xTUx-TFL2-TDF-191018-ESA Page | 1
Models
EFCB10TU2 (24Vac / 2 relays)
EFCB10TU4 (24Vac / 4 relays)
EFCB11TU2 (120Vac / 2 relays)
EFCB11TU4 (120Vac / 4 relays)
EFCB12TU2 (240Vac / 2 relays)
EFCB12TU4 (240Vac / 4 relays)
TFL24 Series Digital Room Sensor
TFL24 (With temperature sensor)
TFLH24 (With temperature and humidity sensor)
TFLG24 (With temperature and CO2 sensor)
TFLGH24 (With temperature, CO2and humidity
sensors)
TDF Series Digital Room Sensor
TDF00 (Vertical Grey LCD, white enclosure)
TDF30 (Vertical Black LCD, black enclosure)
TDF60 (Vertical Black LCD, white enclosure)
TDF10 (Horizontal Grey LCD, white enclosure)
TDF40 (Horizontal Black LCD, black enclosure)
TDF70 (Horizontal Black LCD, white enclosure)
EFCB Series
TFL24 Series
TDF00 / TDF30 /
TDF60 Series
TDF10 / TDF40 /
TDF70 Series
Description
The EFCB Series Networkable Fan Coil Controller, and
TFL24 and TDF Series Digital Room Sensors are designed
for simple and accurate control of any fan coil application. The
BACnet Fan Coil Controller is mounted inside the fan coil
cabinet and incorporates a configurable fan coil algorithm,
variable three speed fan control and either modulating or
digital heating and cooling outputs. All inputs and high/low
voltage outputs are centralized at the control module in the
fan coil cabinet.
Applications
•Compatible with 2 or 4 pipe systems
•Fan coil unit (up to 3 speeds and/or analog 0-10 Vdc)
•Cooling signal (on/off, floating or modulating 0-10 Vdc)
•Heating signal (on/off, floating, pulse or modulating 0-10
Vdc)
•Cool, Heat, Reheat, Reheat with fan, Changeover, Fan,
Humidify and Dehumidify by cooling.
Features
•Built-in configurable fan coil algorithms
•Up to 10 inputs and 15 outputs (configurable)
•Select direction on digital inputs and all outputs
•Selectable proportional control band and dead band
•Selectable fan speed contacts
•Independent cool/heat setpoint for NSB/OCC mode
•No occupancy and NSB override
•Selectable internal or external temperature sensor
(10KΩ)
•Change over by contact or 10KΩ temperature sensor
•Internal and external temperature sensor calibration
•Freeze protection
•Multi level lockable access menu and setpoint
•Removable, raising clamp, non-strip terminals
Digital Room Sensor Features
•Backlit LCD with simple icon and text driven menus
•Select digital room sensor’s default display
•BACnet service port via on-board mini USB connector
•Selectable Fahrenheit or Celsius scale
•3-wire connection to controller and 4 push buttons
Network Communication
•BACnet®MS/TP or Modbus communication port
•Select MAC address via DIP switch or via network
•Automatic baud rate detection
BACnet MS/TP®
•Automatic device instance configuration
•Copy and broadcast configuration via digital room sensor
menu or via BACnet to other controllers
•BACnet scheduler
•Firmware upgradeable via BACnet
•Support COV (change of value)
Modbus
•Modbus @ 9600, 19200, 38400 or 57600 bps
•RTU Slave, 8 bits (configurable parity and stop bits)
•Connects to any Modbus master

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 2
Controller Specifications
Description
EFCB10TU2
EFCB10TU4
EFCB11TU2
EFCB11TU4
EFCB12TU2
EFCB12TU4
Inputs
2 fixed analog inputs (external temp. and changeover sensors); 10KΩ or contact
4 analog inputs (0-10 Vdc or 10 KΩ via DIP switches)
3 configurable digital inputs
1 night setback or occupancy sensor input
Outputs
4 analog , 0-10 Vdc configurable outputs (changeover/cooling/heating, fan, humidity)
4 configurable TRIAC outputs (changeover/cooling/heating)
3 speed fan (Motor and/or compressor inductive ratings: ¼ Hp/10 LRA/2.5 FLA 240 Vac Maximum
Resistive ratings: 7 Amp/1680 W at 240 Vac Maximum); configurable up to 3 speeds
2 or 4 configurable digital outputs (changeover/cooling/heating, humidity, 3A dry contact)
Power supply
24 Vac
120 Vac
240 Vac
Power consumption
8 VA max. 24 Vac thermal fused.
BACnet
BACnet®MS/TP @ 9600, 19200, 38400 or 76800 bps (BAS-C)
Modbus
Modbus RTU slave @ 9600, 19200, 38400 or 57600. Selectable parity and stop bit configuration:
No parity, 2 stop bit
Even parity, 1 stop bit
Odd parity, 1 stop bit
Communication
Connections
24 AWG twisted-shield cable (Belden 9841 or equivalent)
Electrical Connections
0.8 mm2 [18 AWG] minimum
Operating temperature
0ºC to 50ºC [32ºF to 122ºF]
Storage temperature
-30ºC to 50ºC [-22ºF to 122ºF]
Relative Humidity
5 to 95% non condensing
Enclosure protection
IP 30 (EN 60529)
Weight
635 g. [1.4 lb]
Dimensions:
A = 6.30” | 160mm
B = 5.00” | 126mm
C = 2.25” | 57mm
B
AC

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 3
Digital Room Sensor Specifications
Description
TFL24 and TDF Series
Temperature Sensor (TFL24)
Setpoint Range
10ºC to 40ºC [50ºF to 104ºF]
Control Accuracy
±0.5ºC [0.9ºF] @ 22ºC [71.6ºF] typical calibrated
Display Resolution
±0.1ºC [0.2ºF]
Humidity Sensor (TFLH24, TFLGH24, and TDF models with Humidity Sensor)
Setpoint Range
10 to 65%RH
Control Accuracy
±3.5% RH
Display Resolution
0.1%
CO2Sensor (TFLG24, TFLGH24, and TDF models with CO2Sensor)
Operating Principle
Self-calibrating, Non-Dispersive Infrared (NDIR)
Sensor Range
400 to 2000 ppm
Accuracy
±30 ppm ±3% of reading (Accuracy is defined after minimum 3 weeks of continuous operation)
Response Time
2 minutes by 90%
PIR Motion Sensor (TDF00 / TDF30 / TDF60 models with PIR Sensor)
Operating Principle
Passive Infrared (PIR)
Detection Angle
100°
Detection Distance
4m [13ft]
Detection Area
100º
4m
(13ft)
VOC Sensor (TDF00 / TDF30 / TDF60 Series models with VOC Sensor)
Operating Principle
Self-calibrating, Non-Dispersive Infrared (NDIR)
Sensor Range
0-1000 ppb isobutylene equivalent tVOCs
Response Time
<5 seconds for tVOC
Start up Time
15 mintues
Other
Electrical connection
3 wires to EFCB controller and 2 wires (optional) to BACnet network service port
0.8 mm2 [18 AWG] minimum
BACnet service port
Mini USB connector
Power supply
24Vac or 24Vdc
Power consumption
1VA
Operating temperature
0ºC to 50ºC [32ºF to 122ºF]
Storage temperature
-30ºC to 50ºC [-22ºF to 122ºF]
Relative humidity
5 to 95 % non condensing
Enclosure protection
IP 30 (EN 60529)
Weight
120 g. [0.25 lb]
Note: The TFL24/TDF digital room sensor functions only with the EFCB controller. All the inputs/outputs are located on the EFCB except for the
temperature, humidity and CO2sensors built-in the TFL24/TDF and PIR and VOC sensors built in the TDF00 / TDF30 / TDF60 models.

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 4
Dimensions
TFL24
A = 2.85” | 73mm
B = 4.85” | 123mm
C = 1.00” | 24mm
D = 2.36” | 60mm
E = 3.27” | 83mm
TDF10 / TDF40 / TDF70 Series
A = 5.24” | 133mm
B = 2.87” | 73mm
C = 3.74” | 95mm
D = 1.22” | 31mm
E = 0.75” | 19mm
F = 2.00” | 51mm
G = 2.18” | 55mm
TDF00 / TDF30 / TDF60 Series
A = 4.88” | 124mm
B = 3.25” | 83mm
C = 1.75” | 44mm
D = 0.96” | 24mm
E = 2.07” | 53mm
F = 2.36” | 60mm
G = 3.28” | 83mm
H = 0.78” | 20mm (without CO2)
0.95” | 24mm (with CO2)
E
D
B
A
CPIR Sensor
(Optional)
G
F
H
A
B
C
D
E
ºF / º C
A
B
C
D
E
F
G
R.095 TYP
R6.542 TYP

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 5
TDF Models
Horizontal
Model #
Temp
RH
CO2
TDF10-100
TDF40-100
TDF70-100
●
TDF10-101
TDF40-101
TDF70-101
●
●
TDF10-102
TDF40-102
TDF70-102
●
●
●
TDF10-103
TDF40-103
TDF70-103
●
●
TDF10 Series
TDF40 Series
TDF70 Series
Vertical
Model #
Temp
RH
CO2
PIR
VOC
TDF00-100
TDF30-100
TDF60-100
●
TDF00-101
TDF30-101
TDF60-101
●
●
TDF00-102
TDF30-102
TDF60-102
●
●
●
TDF00-104
TDF30-104
TDF60-104
●
●
TDF00-105
TDF30-105
TDF60-105
●
●
●
TDF00-106
TDF30-106
TDF60-106
●
●
●
●
TDF00-107
TDF30-107
TDF60-107
●
●
●
●
●
TDF00 Series
TDF30 Series
TDF60 Series

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 6
Interface
TFL24
Cooling ON
A: Automatic
Communication Status
Alarm status
Heating ON
A: Automatic
Menu set-up Lock
Energy saving mode
Fan ON
A: Automatic
Programming mode
(Technician setting)
Percentage of humidity
Humidity ON
33, 66 or 100%
output
Dehumidification ON
33, 66 or 100% output
or
ºC: Celsius scale
ºF: Fahrenheit scale
TDF10 / TDF40 / TDF70 Series
Network
Communication
User Lock
Programming Mode
(Technician Setting)
Alarm Status
Energy Saving
Mode (NSB/OCC)
Schedule
Time
ppm
Parts Per Million
°C
°F
%RH
ºC: Celsius Scale
ºF: Fahrenheit Scale
%RH: Humidity
A
Automatic Mode
Cooling
Heating
Fan
Humidify
De-humidify
TDF00 / TDF30 / TDF60 Series
AM PM
F
C
%RH
Network
Communication
User Lock
Programming
Mode
(Technician
Setting)
Alarm Status
Energy Saving
Mode
(NSB/OCC)
AM PM
Time
°C
°F
%RH
ºC: Celsius Scale
ºF: Fahrenheit
Scale
%RH: Humidity
A
Automatic Mode
Cooling
Heating
Fan
Humidify/
De-humidify
C
F
%RH
MO TU WE TH FR SA SU
AM PM
.
.
.
.
%RH
C
F
AM
PM
%RH
F
C
ppm
1 2 3 4 5 6 7
123456 7

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 7
Mounting Instructions
TFL24
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the captive screw that’s holding the base and the front cover of the unit together.
B. Lift the front cover of the unit to separate it from the base.
C. Pull all wires through the holes in the base.
D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections.
E. Mount the control module on the base and secure using the screw.
TDF10 / TDF40 / TDF70 Series
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the wall mounting plate (highlighted) from the back of the digital room sensor.
B. Install the mounting plate on the gang box.
C. Pull the wires through the base hole and make the appropriate connections.
D. Mount the digital room sensor onto the wall plate. To mount it correctly, place the top of the digital room sensor on the
mounting plate first and push it into the grooves to snap it into place.
E. Secure the digital room sensor using the screw (supplied).
TDF00 / TDF30 / TDF60 Series
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the captive screw that’s holding the base and the front cover of the unit together.
B. Lift the front cover of the unit to separate it from the base.
C. Pull all wires through the holes in the base.
D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections.
E. Mount the control module on the base and secure using the screw.
ABC D E
A
E
D
C
B
ABCE
D

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 8
BACnet or Modbus Address DIP Switch (DS2)
MAC address for communication, are selectable by DIP switch using binary logic. If you do not change device instance in program mode, it will be
automatically modified according to the MAC address.
Note: Avoid using addresses above 246 when selecting Modbus MAC address.
MAC Address
DS.1 = 1
DS.2 = 2
DS.3 = 4
DS.4 = 8
DS.5 = 16
DS.6 = 32
DS.7 = 64
DS.8 = 128
Default Device Instance
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
153000
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
153001
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
153002
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
153003
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
153004
…
…
…
…
…
…
…
…
…
…
126
OFF
ON
ON
ON
ON
ON
ON
OFF
153126
127
ON
ON
ON
ON
ON
ON
ON
OFF
153127
* Slave addresses available by setting DS.8 to ON

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 9
Wiring
We strongly recommend that all Neptronic products be wired to a separate grounded transformer and that transformer shall service
only Neptronic products. This precaution will prevent interference with, and/or possible damage to incompatible equipment.
For 120/240Vac models, it is recommended to have separate power sources for the EFCB controller and the Fan Coil Unit, in order
to protect the device circuitry from any surge in power supply.
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4
DS2 DS1
Fuse 10A
F1
TB1
1
2
3
4
5
6
7
TFL24 and TDF
1 2 3
24Vac
COM
COM BUS
IN B-
IN A+
COM
3
DS1 DIP Switch
1 = AI3
2 = AI4
3 = AI5
4 = AI6
Off: Temp. sensor (10k ohms)
On: Voltage (0-10Vdc)
DS2 DIP Switch
The 8 DIP switches
represent a binary logic to
calculate the MAC address.
Default = all OFF
1 2
Optional:
connect
to enable
service port
To other
BACnet
device
COM
24Vac
DI1
1
DI2
2
COM
3
DI3
4
DI4
5
AI3
1
AI4
2
COM
3
AI5
4
AI6
5
AI1
1
COM
2
AI2
3
COM
3
AO3
4
AO4
JP1
TO3 / 4
INT EXT
PWR
STATUS
8 7 6 5 4 3 2 1
JP2
TO1 / 2
INT
EXT
RET
Line
RET
TB7
TB8
TB9
TB10
TB11
AO1
1
AO2
21 2
5
TB6
TB5
TB1
TB4
JP3None
120 Ohms
COM
TO4
TO3
TI3 | TI4
COM
TO2
TI1 | TI2
TO1
COM
TB3
RET
RET
TB2
DO2 (3A)
654 3 2 1
4 3 2 1
DO1 (3A)
RET
FAN MED (7A)
FAN LOW (7A)
FAN HIGH (7A)
DO3 (3A)
4 analog outputs (config.)
Cool,heat,reheat,changeover, fan,
humidify&dehumidify by cooling
0-10Vdc (configurable min/max)
Direct or reverse
4 analog inputs (config.)
0-10Vdc or 10kOhms
via DIP switch
NSBor OCC Sensor
0
3-speed fan
4 3 2 1
RET
DO4 (3A)
4 digital outputs (config.)
Cool, heat, reheat, changeover,
humidify & dehumidifyby cooling.
Configurableclose/open percent
Direct or reverse
LD3 = TX
LD4 = RX
4 TRIACoutputs (config.)
Cool, heat, reheat, & changeover
On/Off (config close/open percent)
Floating (config float time)
Pulse (heat and reheat only)
Direct or reverse
JP2 TO1 /2 (Input Voltage)
INT = 24Vac supplied internally from TB11
EXT = Apply 24Vac to pin 1 of TB1
JP1 TO3 /4 (Input Voltage)
INT = 24Vac supplied internally from TB11
EXT = Apply 24Vac to pin 5 of TB1
JP3 (Endof line)
None= No end of line
120Ω= Last node on network
LEDs
POWER = On when 24Vac appliedto TB11
STATUS = Flashes when communicating with digital room
sensor
LD3 = Flashes when transmitting (TX) via BACnet
LD4 = Flashes when receiving (RX) via BACnet
Input
Output
3 digital inputs (config.)
Override, flow switch, window/door
contact, dirty filter, overheat
EFCB10TUx
24Vac (input)
With lowvoltage model, 24Vac must be
applied to TB11 in order to supply the left
side of board and all TRIAC outputson TB1.
EFCB11TUx/EFCB12TUx
24Vac (output)
With line voltage models (120 Vac/240Vac),
TB11provides a 24Vac low voltage output.
Power Input (24, 120, or 240Vac)
Applies to all relays and digital outputs
If 120Vac or 240Vac, TB11 = Out
If 24Vac, TB11 = In
External Temperature Sensor (10kOhms)
Changeover Sensor
External Temperature Sensor
(0-10 Vdc or 2-10 Vdc)

Networkable Fan Coil Controller
Specification and Installation Instructions
www.neptronic.com Page | 10
PCB Drawings
TFL24 Digital Room Sensor
3 wire cable (TB1 #1, 2 & 3)
Connect TB1 #6 (A+) & #7 (B-) to EFCB to enable the BACnet service
port.
Mode Selection (JP1)
RUN:
Digital Room Sensor is in Operation Mode.
Digital Room Sensor must be set in this
mode for normal system operation. If not
locked, setpoint and control mode can be
changed by the end user.
PGM:
Digital Room Sensor is set in
Programming Mode.
Refer to the following sections for more
details.
TDF10 / TDF40 / TDF70 Series
3 wire cable (TB1 #1, 2 & 3)
Connect TB1 #6 (A+) & #7 (B-) to EFCB to enable the BACnet service
port.
CO2sensor
A+
DATA
PWR
COM
B-
1 2 3 4 5 6 7
JP1
Avoid touching the CO2
sensor as this may cause
incorrect readings
Mode Selection (JP1)
RUN:
Digital Room Sensor is in Operation Mode.
Digital Room Sensor must be set in this
mode for normal system operation. If not
locked, setpoint and control mode can be
changed by the end user.
PGM:
Digital Room Sensor is set in
Programming Mode.
Refer to the following sections for more
details.
TDF00 / TDF30 / TDF60 Series
3 wire cable (TB1 #1, 2 & 3)
Connect TB1 #6 (A+) & #7 (B-) to EFCB to enable the BACnet service
port
VOC sensor
(models with VOC)
JP1
PGM
RUN
CO2sensor
(models with CO2)
1
2
3
4
7
6
5
B-
A+
COM
PWR
DATA
Avoid touching the CO2 and VOC
sensors as this may cause
incorrect readings.
Mode Selection (JP1)
RUN:
Digital Room Sensor is in Operation Mode.
Digital Room Sensor must be set in this mode
for normal system operation. If not locked,
setpoint and control mode can be changed by
the end user.
PGM:
Digital Room Sensor is set in Programming
Mode.
Refer to the following sections for more details.
Mode Selector Jumper
RUN = Operation Mode
PGM = Programming Mode
BACnet
service port
Avoid touching the CO2
sensor as this may cause
incorrect readings
TB1
1
2
3
4
5
6
7
PGM RUN
A
B
C
JP1
Optional: connect
to BACnet network to
enable service port
CO2sensor
(TFLG and TFLGH24 only)
A+
DATA
PWR
COM
B-
Connect to EFCB
fan coil controller
Temperature sensor (all models)
Humidity sensor (TFLH24 and TFLGH24 only)
PGM
RUN
JP1
PGM
RUN
JP1
PGM
RUN
JP1
PGM
RUN
JP1
PGM
RUN
JP1
PGM
RUN
JP1