Neptune SS9461SCM User manual

图纸编码
RD-SS9461-SM-01(SS-I)
版本号
A
SS9461SCM 英文说明书
编辑日期
2021/4/21
制作
刘丽萍
审核
白丹
批准
余泽松
物料编码
1320109407
备注
以A4 样板打印
F

MODEL: SS9461SCM
NEPTUNE 300 BEAM
USER MANUAL
NEPTUNE 300 BEAM
SS9461

1
1 PRODUCT
1.1 TECHNICAL SPECIFICATIONS
Type
SS9461SCM
LED colors
1 LED(CW) 200W
Angle
2°
Power
320W
Control Protocol
DMX512，RDM，ARTNET，sACN，W-DMX（Optional）
Voltage Range
AC100~240V,50/60Hz
Input Current
110V/3A,220V/1.5A
Protection
IP65
Operation Temperature
-20℃~45℃
Dimensions
411x280x603mm
Weight
28kg

2
1.2 Safety Notes
IMPORTANT
．．．．．．．．．
This product must be installed by a qualified professional.
In order to maintain this condition and to ensure a safe operation, it is absolutely necessary
for the user to follow the safety instructions and warning notes
The manufacturer will not accept liability for any resulting damages caused by the
non-observance of this manual or any unauthorized modification to the device.
CAUTION!
．．．．．．．．
Make sure that the available voltage is not higher than stated on the rear panel.
Do not touch the power cables if your hands are wet.
The earth wire must always be connected to the ground. Therefore it is essential to connect
the yellow/green conductor to earth.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the
device and the power-cord from time to time. The electric connection, repairs and servicing
must be carried out by a qualified employee.
Always disconnect power input cable to completely remove power from unit when not in use
or before cleaning or servicing the fixture.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
The surface of the product’s casing can reach up to 70°C (158°F) during operation. Avoid
contact by persons and materials. Do not install the product in a location where there is a risk
of accidental contact. Allow the product to cool for at least 10 minutes before handling.
For replacement use lamps and fuses of same type and rating only.
Please protect the fixture and avoid destroy during transport and installation. If there is any
damage to the coating, the shell may be corroded.
When hanging lamps and lanterns, it is necessary to verify that facilities and hooks can bear
at least 10 times the weight of lamps and lanterns.
Fix the safety rope at the correct holes only. Only operate the fixture after having checked
that the housing is firmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded. Do not operate the
product if the ambient temperature (Ta) exceeds 45°C (115°F).
During the initial start-up some smoke or smell may arise. This is a normal process and does
not necessarily mean that the device is defective.
E
．
lectrical
．．．．．．．．．
W
．
arning
．．．．．．
The light source contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person
For replacement use lamps and fuses of same type and rating only.
The lens has to be replaced when it is obviously damaged, so that its function is impaired, e.
g. due to cracks or deep scratches!

3
Keep the product well away from flammable materials
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
Keep all combustible materials (e.g. fabric, wood, paper) at least 500 mm (20 in.) away from
the product.
Ensure that there is free and unobstructed airflow around the product. Provide a minimum
clearance of 150 mm (6 in.) around fans and air vents.
Do not illuminate surfaces within 3 m (10 ft.) of the product.
Do not install a fuse that has a higher rating than the one originally installed in the product.
Do not bypass fuses.
Do not stick filters, masks or other materials onto optical components.
If the fixture seems to be abnormally hot, shows signs of melting or emits smoke, disconnect
the fixture from power immediately and allow it to cool. Do not touch the fixture without
heatproof safety gloves. Keep the fixture well away from combustible and flammable
materials.
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
Do not point the front of the fixture towards the sun or other strong light sources. The
front lens focuses and concentrates light just like a magnifying glass. Strong light can
cause internal damage to the fixture, melting components or starting an internal fire
within seconds.
To avoid problems from strong light sources:
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
Do not expose the front of a fixture to sunlight or any other strong light source. Avoid pointing
other high-powered beam lights directly at the fixture.
Do not focus a light beam from one lighting fixture directly towards another.
For outdoor applications during daylight, make sure that the front face of any fixture is
shielded or points away from the sun, even when not in use.
Do not expose the product to heat (from other lighting fixtures for example).

4
2 INSTALLATION
2.1 MOUNTING
Truss installation
．．．．．．．．．．．．．．．．．
Keep all combustible materials (e.g. fabric, wood, paper) at least 500 mm (20 in.) away from
the product.
For overhead use, always install a safety cable that can hold at least 10 times the weight of
the fixture.
For overhead installation, the fixture must be always secured with a safety wire that can bear
at least 10 times the weight of the fixture；
Secure the fixture with a safety cable through the rear safety eye and truss as shown..
Ensure that the structure (truss) to which you are attaching the fixture is secure
2.2 Fuse replacement
Remove the safety cap by a screwdriver.
Fetch the old fuse from safety cap.
Install a new fuse.
Install the safety cap.

5
2.3 POWER CONNECTIONS
This product has an auto-ranging power supply that can work with an input voltage range of
100–240 VAC, 50/60 Hz.
POWER Linking: 2 units@110V；4 units@220V.
2.4 Data network requirements
Connect the DMX512 controller to the units in series. A DMX 512 data link is required in
order to control the fixture via DMX. The fixture has 3/5-pin XLR connectors for DMX data
input and output.
Each unit has 13 DMX channels so the DMX Addresses should increase by increments of 1，
(Nx1)+1，(Nx2)+1，(Nx3)+1...
Any DMX address in the range from 001 to 512 may be used.
Connect the DMX-output of the first fixture in the DMX chain with the DMX-input of the next
fixture. Always connect one output with the input of the next fixture until all fixtures are
connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 Ω resistor between Signal (–) and Signal (+) into a 3/5-pin XLR-plug and plug it in the
DMX-output of the last fixture.

6
3 FUNCTIONS AND SETTINGS
3.1 DISPLAY OPERATION
LEFT：Used to access the menu or to return a previous menu option;
RIGHT：Used to select and store the current menu or confirm the current function value or
option within a menu;
UP：Navigates downwards through the menu list and increases the numeric value when in a
function;
DOWN：Navigates upwards through the menu list and decreases the numeric value when in
a function；

When the display locked, please unlock the display as below:
1. Keep pressing BACK around 5sec, until the display shows inset password.
2. Press ―up down up down, enter‖to unlock.
3.2 Menu Map
ADDRESS
001 –512(Default 001)
DMX address setting
PERSON
BASIC
Use the menu to select desired channel
mode
STANDARD (Default)
EXTEND
RUNMODE
DMX512 (Default)
Select Signal
Default: DMX512
ARTNET：Ethernet control
CUSTOM1-2 Set up get into EDIT MENU
edit
ARTNET
ARTNET TO DMX
sACN
AUTO
CUSTOM1
CUSTOM2
OPTION
PAN INVERT
NORMAL (Default)
PAN moving direction selection
INVERT
TILT INVERT
NORMAL (Default)
TILT moving direction selection
INVERT
PERFORM
STUDIO
Fan mode low speed
POWER
Fast rotation of fan，all power
LIVE (Default)
Automatic rotation of fan

7
BLACKOUT
OFF (Default)
Select OFF blackout without delay
Select ON Blackout delay 3s
ON
DIMMER
DIM4 (Default)
Dimming curves OFF (fast) to DIM4 (slow)；
OFF
LED PWM
1200Hz (Default)
Sets the PWM frequency
2400Hz
4000Hz
6000Hz
25000Hz
DMX ERROR
SAVE (Default)
Hold after loss of DMX signal
BLACK
Blackout after loss of DMX signal
DISPLAY TIME
On
Display backlight always on
30s
Turns off display backlight after 30s/1min
/2min of inactivity
1min (Default)
2min
DISPLAY LOCK
OFF
Locks display (passcode is <UP>,
<DOWN>,<UP>, <DOWN>, <ENTER>)
ON (Default)
LOAD PARA
OFF
Not upload data
ON (Default)
Upload data
SETTING
RECOVERY
****
Restore default factory settings.
CLEAN EDIT1
****
Clean customer self-editing scene 1
CLEAN EDIT2
****
Clean customer self-editing scene 2
WDMX HIDE
NO
Hide wireless mode WDMX reset and
signal hide and the default is wired mode
only
YES
NETWORK
NET SWITCH
2.xxx.xxx.xxx
Net switch off IP mode
10.xxx.xxx.xxx
Net switch on IP mode
UNIVERS
0-255
Packet group Settings
IP MODE
DEFAUL IP
Default IP
CUSTOM IP
Customer's IP
CUSTOM IP
XX.XX.XX.XX
Customer's IP setting
PT ENCODER
OFF
XY Encoder switch.
OFF is close; ON is open.
ON
WDMX RESET
NO
Do not clear the receiver's message.
YES
Clear the receiver's message
SIGNAL
ONLY XLRDMX
ONLY XLR is wire only
XLRDMX FIRST
XLR FIRST is wire first
ONLY WDMX
ONLY WDMX is wireless only
WDMX FIRST
WDMX FIRS is wireless first
WDMX TO XLRDMX
WDMX TO DMX is wireless to wired
EDIT
EDIT 1-2
STEP 1-30
PAN
0-255
Edit the custom programs1-30

8
TILT
0-255
Select play 【EDIT 1】in RUNMOEDE
CUSTOM 1; Select play 【EDIT 2】in
RUNMOEDE CUSTOM 2
PT SPEED
0-255
COLOR
0-255
GOBO.ROTA
0-255
ROTA.GOBO
0-255
COLOR GOBO
0-255
PRISM 1
0-255
PRISM 2
0-255
FOCUS
0-255
DIMMER
0-255
STROBE
0-255
TIME
0-255
USE
YES/NO
Select YES to run the steps user need.
MANUAL
AUTO TEST
CHANNEL
PAN
0-255
Manual control channel
TILT
0-255
PT SPEED
0-255
COLOR
0-255
GOBO.ROTA
0-255
ROTA.GOBO
0-255
COLOR GOBO
0-255
PRISM 1
0-255
PRISM 2
0-255
FOCUS
0-255
DIMMER
0-255
STROBE
0-25
DEBUG HIDE
NO
Factory testing mode. All stepper motors
are not controlled by signal, It only works
again after the reset.
YES
RESET
ALL RESET
Select Yes/No to carry out all reset
PT RESET
Select Yes/No to carry out P/T reset
COLOR SYSTEM
COLOR/CMYK reset
OTHER
Zoom/ Focus reset
INFO
FIXTURE HOURS
Hours of fixture use
LED USE HOURS
LED use time
TEMPERATURE
LED temperature
VERSION
Software versions
NETWORK
Check network parameter
RDM
UID
0x388Axxxxxxxx
Check fixture's ID
LABEL
NEPTUNE 300 BEAM
Check fixture's LABEL
SYSTEM
ERROR
MEMORY IC
Memory IC
ANGLESENSOR
Angle Sensor
PAN SENSOR
Pan Sensor

9
PAN ENCODER
Pan Encoder
PAN DRIVEIC
Pan Drive IC
TILT SENSOR
Tilt Sensor
TILT ENCODER
Tilt Encoder
TILT DRIVEIC
Tilt Drive IC
TEMPERATURE
Temperature
COLOR RESET
Color reset
GOBO RESET
gobo reset
RGOBO RESET
Rgobo reset
COLOR GOBO RESET
Color gobo reset
PRISM 1 RESET
Prism 1 reset
PRISM 2 RESET
Prism 2 reset
FOCUS RESET
Focus reset
SERVICE
****
PAN
±127
Pan position fine adjustment
TILT
±127
Tilt position fine adjustment
COLOR
±127
Color position fine adjustment
GOBO.ROTA
±127
Rotate Gobo position fine adjustment
ROTA.GOBO
±127
Gobo position fine adjustment
COLOR GOBO
±127
Color gobo position fine adjustment
PRISM 1
±127
Prism1 position fine adjustment
PRISM 2
±127
Prism2 position fine adjustment
FOCUS
±127
Focus position fine adjustment
OTHER
±127
All passwords of this product are <UP>, <DOWN>,<UP>, <DOWN>, <ENTER>)

10
4 USING A DMX512 CONTROLLER
4.1 DMX CONTROL
BASIC
(13CH)
STANDARD
(18CH)
Extend
(19CH)
Value
Function
CH.1
CH.1
CH.1
000-255
PAN 0-540°
-
CH.2
CH.2
000-255
PAN FINE
CH.2
CH.3
CH.3
000-255
TILT 0-270°
-
CH.4
CH.4
000-255
TILT FINE
CH.3
CH.5
CH.5
000-255
PT Speed
CH.4
CH.6
CH.6
COLOR WHEEL 9+1
000-007
WHITE
008-013
COLOR 1
014-019
COLOR 2
020-025
COLOR 3
026-031
COLOR 4
032-037
COLOR 5
038-043
COLOR 6
044-049
COLOR 7
050-055
COLOR 8
056-063
COLOR 9
064-191
COLOR WHELL1 0-360°
192-222
COLOR WHELL1 RAINBOW EFFECT(SPEED 100%->1)
223-224
STOP
225-255
COLOR WHELL1 RAINBOW EFFECT(SPEED 1->100%)
-
-
CH.7
000-255
COLOR WHEEL FINE
CH.5
CH.7
CH.8
ROTATING GOBO 8+1
000-010
ROTATING WHITE
011-016
ROTATING GOBO 1
017-022
ROTATING GOBO 2
023-028
ROTATING GOBO 3
029-034
ROTATING GOBO 4
035-040
ROTATING GOBO 5
041-046
ROTATING GOBO 6
047-052
ROTATING GOBO 7
053-058
ROTATING GOBO 8
059-066
ROTATING GOBO 1 SHAKE (SPEED 1 —> 100%)
067-074
ROTATING GOBO 2 SHAKE (SPEED 1 —> 100%)
075-082
ROTATING GOBO 3 SHAKE (SPEED 1 —> 100%)
083-090
ROTATING GOBO 4 SHAKE (SPEED 1 —> 100%)

11
091-098
ROTATING GOBO 5 SHAKE (SPEED 1 —> 100%)
099-106
ROTATING GOBO 6 SHAKE (SPEED 1 —> 100%)
107-114
ROTATING GOBO 7 SHAKE (SPEED 1 —> 100%)
115-122
ROTATING GOBO 8 SHAKE (SPEED 1 —> 100%)
123-127
WHITE
128-190
ROTATING GOBO FLOWING WATER EFFECT (SPEED 100 —> 1%)
191-192
STOP WATER EFFECT
193-255
ROTATING GOBO FLOWING WATER EFFECT (SPEED 1 —> 100%)
CH.6
CH.8
CH.9
GOBO ROTATING
0-120
ROTATING GOBO ANGLE ADJUSTMENT (0 —> 360°)
121-125
STOP
126-165
ROTATING GOBO SHAKE (SPEED 1 —> 100%)
166-170
STOP
171-210
ROTATING GOBO POSITIVE ROTATION (SPEED 100% —> 1)
211-215
STOP
216-255
ROTATING GOBO REVERSE ROTATION (SPEED 1 —> 100%)
-
CH.9
CH.10
000-255
GOBO ROTATING FINE
CH.7
CH.10
CH.11
COLOR EFFECT WHEEL
0-10
WHITE
11-145
COLOR EFFECT INSERT AND ADJUST THE ANGLE (0 —> 360°)
146-150
STOP
151-200
COLOR EFFECT INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
201-205
STOP
206-255
COLOR EFFECT INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
CH.8
CH.11
CH.12
PRISM 1
0-10
WHITE
11-145
PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)
146-150
STOP
151-200
PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
201-205
STOP ROTATION
206-255
PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
CH.9
CH.12
CH.13
PRISM 2
0-10
WHITE
11-145
PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)
146-150
STOP
151-200
PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
201-205
STOP ROTATION
206-255
PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
CH.10
CH.13
CH.14
000-255
FOCUS
-
CH.14
CH.15
000-255
FOCUS FINE

12
CH.11
CH.15
CH.16
000-255
DIMMER
-
CH.16
CH.17
000-255
DIMMER FINE
CH.12
CH.17
CH.18
STROBE
0-9
NO FUNCTION
10-99
STROBE（FROM SLOW TO FAST）
100-109
NO FUNCTION
110-179
LIGHTNING STROBE
180-189
NO FUNCTION
190-255
RANDOM SROBE
CH.13
CH.18
CH.19
CONTROL
000-010
NO FUNCTION
011-020
PAN/TILT BLACK ACTIVATED
021-030
PAN/TILT BLACK DEACTIVATED
031-040
PAN INVERT
041-050
TILT INVERT
051-060
PAN/TILT INVERT OFF
061-100
RESERVED
101-110
DIM4
111-120
OFF
121-150
RESERVED
151-160
1200Hz
161-170
2400Hz
171-180
4000Hz
181-190
6000Hz
191-200
25000Hz
201-210
ALL RESET
211-220
XY RESET
221-230
COLOR\GOBO SYSTEM RESET
231-240
FOCUS RESET
241-255
RESERVED