NESTOR MARTIN R25-O25 User manual

S25##3710A
R25- O25
DIRECT VENT GAS STOVES
INSTALLATION AND OPERATING INSTRUCTIONS
THERMIC DISTRIBUTION EUROPE
5 VOIE AXIALE
5660 COUVIN, BELGIUM
Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
- Open windows
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency
or the gas supplier.
WARNING
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

S25##3710A
Installation Requirements for the Commonwealth of Massachusetts
In the Commonwealth of Massachusetts, the installer or service agent shall be a plumber or gas fitter licensed by the
Commonwealth.
When installed in the Commonwealth of Massachusetts or where applicable codes; the unit shall be installed with a CO
detector per the requirements listed below.
1. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment, where the bottom of the vent
terminal and the air intake is installed below four feet above grade the following requirements must be satisfied:
A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and
alarm shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA
720 (2005 Edition).
B. A carbon monoxide detector shall be located in the room that houses the appliance or equipment and shall:
•Be powered by the same electrical circuit as the appliance or equipment such that only one service switch services
both the appliance and the carbon monoxide detector;
•Have battery back-up power;
•Meet ANSI./UL 2034 Standards and comply with NFPA 720 (2005 Edition); and
•Have been approved and listed by a Nationally Recognized Testing Laboratory as recognized under 527 CMR.
C. A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used.
Installation shall be in strict compliance with the manufacturer’s instructions. A copy of the installation instructions shall
remain with the appliance or equipment at the completion of the installation.
D. A metal or plastic identification plate shall be mounted at the exterior of the building, four feet directly above the location
of vent terminal. The plate shall be of sufficient size to be easily read from a distance of eight feet away, and read “Gas
Vent Directly Below”.
2. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment where the bottom of the vent
terminal and the air intake is installed above four feet above grade the following requirements must be satisfied:
A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and
alarm shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA
720 (2005 Edition).
B. A carbon monoxide detector shall:
•Be located in the room that houses the appliance or equipment;
•Be either hard-wired or battery powered or both; and
•Shall comply with NFPA 720 (2005 Edition).
A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used. Installation
shall be in strict compliance with the manufacturer instructions. A copy of the installation instructions shall remain with the
appliance or equipment at the completion of the installation.
For the state of Massachusetts a T-handle gas shut-off valve must be used on a gas appliance. This T-handle gas shut-off valve must be
listed and approved by the state of Massachusetts. This is in reference to the state of Massachusetts state code CMR238.
1

2
S25##3710A
SAFETY PRECAUTIONS
For safe installation and operation of your NESTOR MARTIN stove, please, carefully read the following
information:
•All NESTOR MARTIN gas fired appliances must be installed in accordance with these instructions.
Carefully read all the instructions in this manual first. Consult the building authority having jurisdiction
to determine the need for a permit prior to commencing the installation.
•Note: failure to follow these instructions could cause a malfunction of the fireplace which could result
in death, serious bodily injury, and/or property damage.
•Failure to follow these instructions may also void your fire insurance and/or warranty.
•Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a qualified service person. More frequent cleaning may
be required due to excessive lint from carpeting, bedding material, etc. it is imperative that control
compartments, burners and circulating air passageways of the appliance be kept clean.
•Due to high temperatures the appliance should be located out of high traffic areas and away from
furniture and draperies. Children and adults should be alerted to hazards of high surface temperatures
and should stay away to avoid burns or clothing ignition.
•Young children should be carefully supervised when they are in the same room as the appliance.
•Clothing or other flammable material should not be placed on or near the appliance.
•Installation must conform with local codes or, in the absence of local codes, with the ANSI Z223.1 and
CSA B149.1
•To prevent injury do not allow anyone who is unfamiliar with the operation to use the stove.
•These appliances should not be used as a drying rack for clothing or for hanging Christmas stockings
or decorations.
•Due to the paint curing on the stove a faint odor and slight smoking will likely be noticed when the
stove is first used. Open a window until the slight smoking stops. Always connect this gas stove to a
chimney and vent to the outside of the building envelope. Never vent to another room or inside a
building. Make sure you use the vent pipe that is specified. Make sure that the vent is properly sized
and is of adequate height to provide the proper draft. Inspect the venting system annually for blockage
and any signs of deterioration.
•Do not operate with cracked or broken glass. Under no circumstances should this appliance be
modified. Parts that have to be removed for servicing must be replaced prior to operating this
appliance. Only parts supplied by NESTOR MARTIN should be used in this appliance and
replacements should only be performed by a licensed or qualified service person.
•Never use solid fuels such as wood, paper, cardboard, coal, or any other flammable liquids etc., in
this appliance.
•Do not use this heater if any part has been under water. Immediately call a qualified service
technician to inspect the heater and to replace any part of the control system and any gas control
which has been under water.
•Do not abuse glass by striking or slamming door shut.

3
S25##3710A
PRODUCT SPECIFICATIONS
Gas type Inlet supply pressure Manifold pressure
Input
Minimum
(inch WC) Maximum (inch WC) Minimum (inch WC) Maximum (inch WC) Minimum (BTU/h) Maximum (BTU/h)
Pilot
orifice
size
Burner
orifice
size
(mm)
Natural 7" 14" 3 " 5" 22,000 30,000 272 4 x 1.19
Propane 11" 14" 5.7" 10.5" 21,000 29,000 221 4 x 0.79
For installation above 2000 feet:
•In Canada, these appliances are certified for altitudes of 0-2,000’ and must be de-rated by 10% for
installation at elevations between 2,000' and 4,500’.
•In the USA, the appliance must be de-rated 4% for every 1,000’ above 2,000’ elevations.
Gas control inlet: ⅜" NPT
Flue pipe outer diameter: 6⅝"
Variable output gas control: SIT Proflame
Pilot: SIT or Honywell
These appliances have been tested by CSA and found to comply with the established standards for direct
vent gas fireplaces and in Canada and the USA as follows:
LISTED GAS FIRED GRAVITY DIRECT VENT WALL FURNACE (EG.95.FS.DV.Nat. & LPG)
TESTED TO: ANSI Z21.886-2003/CSA 2.336-2003 STANDARDS
Direct Vent Type is designated by the suffix DV. This type of appliance draws all of its air for combustion
from outside of the dwelling through specially designed vent pipe.
This fireplace requires ventilation and combustion air to operate properly.
This appliance is only for use with the type of gas indicated on the rating plate. A conversion kit is supplied
with the appliance.
•Certified for use with either natural or propane gases (see appropriate labeling).
•Not for use with solid fuels
•Approved for bedrooms
•Must be installed in accordance with local codes, if any. If none exist use current installation code CSA
B149.1 in Canada or ANSI Z223.1/NFPA 54 in the USA
•Mobile home approved: This appliance must be installed in accordance with the current standards –
Canada CSA Z240.4; USA manufactured home construction and safety standard title 24 CFR, Part
3280.
•May be installed in an aftermarket permanently located, manufactured (mobile) home, where not
prohibited by local codes.
•Must be properly connected to a venting system
•Not approved for closet or recessed installations
The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous
operating conditions and was determined independently of any installed system.
This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or
mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible with other gases, unless a certified kit is used.

4
S25##3710A
R25
S25 H25 R25
A 23¼" 24" 20¼"
B 27 26" 29"
C 18" 14" 14⅝"
D 4½" 4½" 4⅝"
E 5" 3⅓" 6⅜"
F 22" 21" 32"
O25

5
S25##3710A
INSTALLATION
DECIDING WHERE TO LOCATE YOUR STOVE
1. The stove should be located out of traffic and away from furniture and draperies.
2. This stove should have sufficient access for its safe operation and maintenance.
3. Locate a position where the flue system of the stove can be properly installed without damaging the
integrity of the building. e.g. cutting wall or ceiling joists.
4. When the appliance is installed directly on carpeting, tile or other combustible material other than
wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and
depth of the appliance.
5. Check stove and flue system clearance requirements.
6. Locate the stove where it can be accessed by a gas supply line.
7. Locate the stove in a large and open room that is centrally located in the house. This will optimize
heat circulation and comfort.
8. This stove can be installed in bedrooms.
9. The flow of combustion and ventilation air must not be obstructed.
MINIMUM CLEARANCES TO COMBUSTIBLES
A – From side wall to stove: 6"
B – From rear wall to stove: 6"
C – Corner clearance: 6"
From top of stove to combustible: 36"
From front of stove to combustible: 60"
FLOOR PROTECTION
The stove must be installed on rigid flooring. When the stove is installed on any combustible surface other
than wood flooring, a metal or wood panel extending the full width and depth of the unit must be used as a
hearth. There are no other hearth requirements.
WARNING:
-Always maintain required clearances to nearby combustibles to prevent fire hazard. Do not
fill air spaces with insulation. All venting components must maintain a 1" (25mm) clearance
to combustible materials.
-The appliance and vent system must be vented directly to the outside of the building and
never be attached to a chimney serving a separate solid fuel or gas-burning appliance. Each
direct vent appliance must use its own separate vent system. Common vents are prohibited.
-Refer to the manufacturer's instructions included with the venting system for complete
installation procedures.
LOCATION OF THE VENT TERMINAL
The vent terminal must be located observing the minimum clearances shown on pages 6 and 7.
C
B
A
FRONT OF STOVE

6
S25##3710A
VENT TERMINAL CLEARANCES
Installations in Canada1Installations in the United States2
A = Clearance above grade, veranda,
porch, deck, or balcony 12" (30cm) 12" (30cm)
B = Clearance to window or door that
may be opened 12" (30cm) 9" (23cm)
C = Clearance to permanently closed
window 12” (30cm) 12” (30cm)
D = Vertical clearance to ventilated
soffit located above the terminal within
a horizontal distance of 2' (61cm) from
the center line of the terminal
18” (46cm)
18” (46cm)
E = Clearance to unventilated soffit 12" (30cm) 12" (30cm)
F = Clearance to outside corner
6" (15cm) if combustible
2" (5 cm) if non-combustible 6" (15cm) if combustible 2" (5 cm) if non-combustible
G = Clearance to inside corner 6" (15cm) if combustible
2" (5 cm) if non-combustible 6" (15cm) if combustible 2" (5 cm) if non-combustible
H = Clearance to each inside of center
line extended above the
meter/regulator assembly
3' (91cm) within a height of 15ft
extended above meter/regulator
assembly
3' (91cm) within a height of 15ft
extended above meter/regulator
assembly
I = Clearance to service regulator vent
outlet 3' (91cm) 3' (91cm)
J = Clearance to non-mechanical air
supply inlet to building or the
combustion air inlet to any other
appliance
12" (30cm) 9" (23cm)
K = Clearance to a mechanical air
supply inlet 6' (1.83m) 3 ' (91cm) above if within 10' (3m) horizontally
L = Clearance above paved sidewalk
or paved driveway located on public
property
7' (2.13m)†
7' (2.13m)†
M = Clearance under veranda, porch,
deck or balcony 12" (30cm) ‡
12" (30cm)‡
N = Clearance above a roof shall extend a minimum of 24” (61cm) above the highest point when it passes through the
roof surface, and any other obstruction within a horizontal distance of 18” (45cm).
1In accordance with the current CSA-B149.1 Installation Codes
2In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes
†A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves
both dwellings
‡only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor:
NOTE: Local codes or regulations may require different clearances.
Important Note: Vent terminals cannot be recessed into a wall or siding

7
S25##3710A
SPECIAL CLEARANCES FOR VERTICAL VENTING (THROUGH A FLAT ROOF)
VENTING
Your stove is approved for different types of installations:
A. Top flue outlet with side wall venting (using a Simpson Duravent type terminal)
B. Rear flue outlet with side wall venting (using a Simpson Duravent type snorkel)
C. Top flue outlet straight through the roof (using a Simpson Duravent type chimney cap)
In each type of installation, it is essential to respect the minimum clearances to combustible materials. It is
recommended that a bead of RTV High Temperature Silicone be applied to each vent joint.
A. B.
C.
vent air intake terminal
Minimum clearances
for vertical terminals
A 4’
B 2’
C 4’
D 2’
E 8’
F 4’

8
S25##3710A
Notes on Side Wall Venting with Top Flue (Configuration A)
When installing a stove with a side wall venting configuration (page 6, fig. A), respect a ratio of one quarter
inch rise for every 2 feet horizontal. The minimum vertical rise allowed is 2 feet (measuring from the top of
the stove's flue collar to the bottom edge of the 90° knee. The minimum horizontal run is also 2 feet
(measuring from the outer edge of the 90° knee to the inner edge of the termination cap. Use a Simpson
Duravent type termination cap. See table above for possible horizontal to vertical ratios.
Follow the vent pipe manufacturer's instructions for assembly and installation.
CAUTION: VENTING TERMINALS CANNOT BE RECESSED INTO A WALL OR SIDING.
Vertical/Horizontal Vent Pipe Ratios
Note:
•The horizontal termination must not be recessed into the exterior wall or siding.
•Horizontal vent runs must be level toward the vent termination.
•Clearances around the vent termination must be maintained.
Total horizontal length
Total vertical height

9
S25##3710A
Notes on Side Wall Venting with Rear Flue Outlet (Configuration B)
To install a stove with a rear flue outlet and side wall vent configuration (page 6, fig.B), begin by placing the
flue collar at the rear of the stove:
1. Unscrew and remove the cast iron flue collar from its original top position.
2. Next, unscrew and remove the inner flue outlet and gasket
3. Unscrew and remove the cast iron cover from the rear flue outlet
4. Unscrew and remove the steel cover and gasket from the rear flue outlet.
5. Attach the inner flue, gasket and cast iron flue collar to the rear of the stove.
6. Block off the top flue outlet by placing the gasket, steel cover and cast iron cover over the top flue
outlet as shown below.
Fit a maximum of 2 feet of vent pipe to the rear flue outlet. Follow the vent pipe manufacturer's instructions
for assembly and installation. Use a Simpson Duravent type snorkel on the outside wall outlet.
CAUTION: VENTING TERMINALS CANNOT BE RECESSED INTO A WALL OR SIDING.
Notes on Vertical Venting (Configuration C)
A vertical vent system must terminate no less than 8 feet and no more than 40 feet above the stove’s flue
collar. The vent pipe must rise a minimum of 2 feet before any offsets is placed. Use a Simpson Duravent
type termination cap.
When planning the installation, make sure to consider:
-All vegetation within three feet which may interfere with the draft.
-Nearby combustible materials that could come into contact with the exhaust gas.
-Other nearby openings (within 12”) through which exhaust gas could re-enter the building.
-Other obstructions or impediments to venting
cast iron flue collar
inner flue collar
gasket
steel cover
cast iron cover
2' max.
length

10
S25##3710A
RESTRICTION PLATE
A set of restriction plates is supplied with your stove to reduce flue draft when required.
These reduction plates are to be used in the following vent configurations:
Top flue exit
2' vertical rise, 2' horizontal length 6' vertical rise, 24' horizontal length
Natural Gas 70mm (2¾") restriction plate 58mm (2¼") restriction plate
Propane No restriction plate required 80mm (3⅛") restriction plate
Rear flue exit
2' horizontal length (w / snorkel)
Natural Gas 60mm (2⅜") restriction plate
Propane 70mm (2¾") restriction plate
Install the restrictor plate directly at the stove outlet as follows:
1. Unscrew and remove the cast iron flue collar.
2. Unscrew and remove the inner flue outlet as well as the gasket.
3. Place the restriction plate on the stove's inner firebox so that it reduces the exhaust outlet diameter.
4. Replace gasket and inner flue collar and fasten using the four screws.
5. Finally, replace the cast iron flue collar.
58mm (2¼") restriction plate
restriction plate
gasket
inner flue outlet
cast iron flue collar
70mm (2¾") restriction plate 60mm (2⅜") restriction plate
80mm (3⅛") restriction plate

11
S25##3710A
CERAMIC BURNER
Your stove is equipped with a 100% ceramic fiber gas burner. Nestor Martin's ceramic burner offers
numerous technical and esthetic advantages:
- Flames and glowing effect similar to a real wood fire
-Highly resistant to leaks, corrosion and deformation over time
-The elasticity of its gel foam ceramic fibers allow the burner to retain its heat resistant properties
without deforming, withstanding even the most extreme temperature variations.
-Increased radiant heat through the glass, while greatly decreasing radiant heat on the valve, receiver
and battery, resulting in longer life for each of the stove’s electronic components.
The burner has several positioning points and notches to help you place the ceramic logs correctly.
Ceramic burner
CONTENTS OF THE LOG KIT
The kit is composed of six ceramic logs. Because they are fragile, the logs are packaged separately to avoid
damage during transport. Using logs other than those supplied by the manufacturer is prohibited, as it may
interfere with the proper functioning of the appliance.
C
A
B
D (x 3)
Positioning
points for
ceramic logs Positioning notches
for lo
g
D

12
S25##3710A
PLACING THE CERAMIC LOGS
Open the firebox door to access the burner, and place the logs as shown in the photos below. It is essential
to the proper operation of the stove that the logs be placed correctly.
65
43
21
Place log A onto the burner's rear positioning
points. Place log B onto the burner's front positioning points.
Place log C across the two other logs. Log C
should be fully supported by the other two logs. Place one of the D logs on the right side of the burner, in the notches and leaning against log A.
Place a D log on the left side of the burner,
leaning against log A. Place a D log to the right of the burner.

13
S25##3710A
PLACEMENT OF THE EMBER GLOW FIBERS (OPTIONAL)
A bag of platinum ember glow fibers is supplied is supplied with the ceramic burner kit. When heated, the
embers glow and flicker, similar to real glowing ash. The embers must be placed correctly in order to
function properly. The pack contains more embers than required. The remaining embers hould be kept for
further service requirements.
Platinum ember glow fibers are made from high-grade ceramic wool. The wool is similar to fiberglass and
should be handled carefully. We recommend the use of a suitable dust mask, gloves or tweezers when
handling the embers. Wash hands immediately after touching to avoid irritation. Store the fibers in a dry
place, away from any flammable liquids.
Before placing, tease out the fabric to form loose, irregular shapes using a tweezers.
The correct placement of the embers is extremely important, as the effect produced can only occur when
they are heated by the gas jets or by direct radiated heat. Do not force the embers into the burner holes, as
to not block them up.
By rubbing the embers into the faces of the logs which are heated by the gas jets, the fibers which adhere to
the logs will glow. With suitable gloves, gently rub a square of fibers into the areas of the logs which glow
when hot.
To left side of
burner
j
ets
In front of
burner
j
ets
To right side of
burner
j
ets
Over burner jets
(
do not force inside
)
Tease out the fabric to
form loose, irregular
shapes. Do not
compress the embers.

14
S25##3710A
CONNECTING THE GAS SUPPLY LINE
WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this
appliance.
The gas line connection may be made using 3/8 " rigid tubing or an approved flex connector. When using
copper or flex connectors, use only fittings approved for gas connections. The gas control inlet is ⅜" NPT.
Upon connection, mark the appropriate fuel type on the CSA rating label.
There must be a gas shutoff between the stove and the supply.
Since some municipalities have additional local codes it is always best to consult your local authorities and
the CAN/CGA-B149.1 Installation Code. For USA gas installations follow either local codes or the current
edition of the National Fuel Gas Code ANSI.Z223.1.
Test to confirm manifold pressures as shown in the table on page 3.
The stove and its individual shutoff valve must be disconnected from the gas supply piping during any
pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).
The stove must be isolated from the gas piping system by closing its individual shutoff valve during any
pressure testing of the gas supply piping system at test pressure equal or less than ½ psi (3.5 kPa).
Always check for gas leaks with a mild soap and water solution. Do not use an open flame for gas leak
testing.
AIR SHUTTER ADJUSTMENT
The stove is shipped from the factory with the air shutter adjusted to the minimum allowed opening.
Depending on the altitude where the stove is located, an air shutter adjustment may be acceptable to
provide a mixed balanced of flame color/glow. The air shutter may only be adjusted to a more open position.
Air shutter opening at
minimum allowed opening.
The air shutter may only be
adjusted to a more open
position.

15
S25##3710A
SIT IPI Sytem

22
S25##3710A
MAINTENANCE
Before conducting any maintenance on the stove, always make sure that the stove is switched off and has
had time to cool.
WARNING: The area around the appliance must be kept clear and free from combustible materials,
gasoline and other flammable vapors and liquids.
•VENTING SYSTEM
The venting system should be examined annually by a qualified technician. Both the inner exhaust pipe
and the outer combustion supply pipe must be checked to confirm that they are unblocked and in good
condition.
•CLEANING OF GLASS
Do not clean glass when hot.
It will be necessary to clean the ceramic glass periodically. During a cold start up condensation will
sometimes form on the glass, this is a normal condition with all glass fireplaces and stoves. However
sometimes this condensation can allow dust and lint to cling to the glass surface. Also, sometimes initial
paint curing of the appliance can leave behind a slight film on the glass. This is a temporary problem. It
is therefore recommended that the glass be cleaned initially after about the first two weeks of use.
After that, depending upon the amount of use, cleaning should be required no more than two or three
times per season. To clean the door, use a mild glass cleaner and a soft cloth. Abrasive cleaners will
damage the glass surface.
•PILOT, BURNER AND FIREBOX
Periodically check the pilot and burner flames visually.
Remove the log set carefully from the combustion chamber.
Vacuum the burner compartment thoroughly.
Vacuum any dust on the logs and remove any lint form the main burner and pilot burner.
After carefully replacing the logs in their correct positions, and the door has been released, relight the
pilot, following the instructions on the attached label. And turn in the main burner.
DOOR HANDLE ADJUSTMENT
Certain models are equipped with an adjustable door latch. For correct operation, the stove door must
be airtight when closed. To adjust the door handle latch:
1. Loosen the locking nut
2. Adjust the bolt in or out as required. The adjustment should be made in such way that when the
handle is in its closed position the door is airtight.
3.
Retighten the locking nut.
Handle shaft Adjustment bolt
Latch
Locking nut

23
S25##3710A
REPLACING THE GLASS
1. Lift the door off the hinges to remove.
2. Unscrew the glass retainer clamps.
3. Use gloves to remove the broken glass.
4. Verify whether the gasket has been damaged or
not. If so, do replace it with a new one. Remove the
old one and place the new one in the same way.
Place the new glass panel in such a position that it
allows thermal expansion.
5. Screw the retainer clamps back on.
6. Put the door back on its hinges.
•Always use original Nestor Martin spare parts.
•Make sure that the edges of the glass panel will not touch metal parts during thermal
expansion.

24
S25##3710A
WARRANTY
NESTOR MARTIN guarantees the equipment against material defects and workmanship. This warranty is
subject to the terms specified below. It gives you specific legal rights, you may also have other rights that
vary from region to region.
The warranty is limited to parts replacement and does not include any labor allowance. Any service charges
for parts replacement are your responsibility.
1 YEAR 5 YEARS
VALVE
BURNER
ENAMELLED PARTS
COMBUSTION CHAMBER
Exclusions :
•Rust due to condensation
•Noises due to dilatation or contraction during the ignition stage or extinction stage
•No warranty is offered on chipping or damage of enamel surfaces. Inspect your stove for damage to the
enamel prior to reception.
•The warranty excludes the logs, thermocouple, gaskets, orifices and window glass.
All warranty service and/or replacement of parts must be performed for you by an individual or servicing
company which has been authorized by NESTOR MARTIN distributors. You may avail of the benefits of
warranty coverage on a failed part by having the servicing company replace the part and return it to the
NESTOR MARTIN distributor for inspection. If the warranty covers the failure, the replacement part will be
free of charge. Transport charges for shipment of the replacement part and return of the failed part are your
responsibility. Any such warranty replacement or repair shall be subject to the terms and conditions of this
warranty for the remainder of the original period of coverage.
This warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration,
misapplication, improper installation or improper maintenance or service.
Any implied warranties of merchantability and fitness applicable to the equipment are limited in duration to
the period of coverage of this express written warranty. Some states do not allow limitation on how long an
implied warranty lasts, so this limitation may not apply to you.
NESTOR MARTIN IS NOT LIABLE for any special, indirect or consequential damages. Some states do not
allow the exclusion or limitation of incidental or consequential changes, so this limitation or exclusion may
not apply to you.
NESTOR MARTIN does not authorize any person or company to assume any other obligation or liability in
connection with the sale, application engineering, installation, use, removal, return or replacement of its
equipment; and no such representations are binding on NESTOR MARTIN.