NETGEAR PowerLINE WiFi 1000 User manual

Quick Start
PowerLINE WiFi 1000
Models PLP1000 and PLW1000v2

2
Package Contents
In some regions, a resource CD is included with your product.

3
Get Started
PowerLINE adapters give you an alternative way to extend your network
using your existing electrical wiring. Plug two or more PowerLINE adapters
into electrical outlets to create a wired network connection. Use a
PowerLINE WiFi access point to add a WiFi access point to your wired
network. You can add up to eight adapters to extend your network.

4
Meet Your Adapters
Before you install your adapters, familiarize yourself with their LEDs,
buttons, and ports.
1
2
1. Power LED 4. Ethernet port 7. WiFi LED
2. Ethernet LED 5. Factory Reset button 8. On/O switch
3. Pick A Plug LED 6. Security button 9. WPS button
8
1
3
4 5 6
2
3
4
5
6
9
7

5
Power LED Solid green. The electrical power is on.
Solid amber. The adapter is in power saving mode (PLP1000
only).
Blinking green. The adapter is in the process of setting up
security.
O. The adapter is not receiving electrical power.
Ethernet LED Solid. The Ethernet port is linked.
O. No Ethernet connection is detected.
Pick A Plug LED The Pick A Plug feature lets you pick the electrical outlet
with the strongest link performance, indicated by the color
displayed by the LED:
Red. Link rate < 50 Mbps (good).
Amber. Link rate > 50 and < 80 Mbps (better).
Green. Link rate > 80 Mbps (best).
O. The adapter did not find any other compatible
PowerLINE devices using the same encryption key.
WiFi LED
Solid blue. The WiFi radio is on.
O. The WiFi radio is o.

6
Factory Reset
button
Press the Factory Reset button for one second, and then
release it to return the PowerLINE adapter to its factory
default settings.
Ethernet port Connect your wired devices, including computers, WiFi
routers, and game consoles, to your PowerLINE network.
Security button Use the Security button to create a secure PowerLINE
network.
On/O switch Use the On/O switch to turn the device on and o.
WPS button Use the WPS button to automatically connect your computer
or other WiFi-enabled devices that support WPS to your
PowerLINE network.

7
Install Your Adapters
Note: Do not plug your PowerLINE adapters into extension cords, power
strips, or surge protectors.
Room 1 Room 2

8
¾To install your adapters:
1. Plug in your new adapters.
2. Wait until the Pick A Plug LEDs are lit.
3. Use your computer, tablet, or smartphone to connect to your new
PowerLINE WiFi network. The WiFi SSID and key are printed on the
adapter label. The SSID is similar to Netgear##_EXT or
Netgear##-5G_EXT.
Congratulations. You installed your adapters and set up your network.
You can customize the network and security settings later.

9
Do More
Aer your PowerLINE network is installed and running, you can use WPS to
connect your access point, expand your network, customize the network
settings, and customize security.
Use WPS to Connect to Your Network
¾To automatically connect to the PowerLINE access point
using a WPS button:
1. Press and hold the WPS button on the PowerLINE access point for
two seconds and release it.
The WiFi LED starts to blink.
2. Press the WPS button on your WiFi-enabled device for two seconds
and release it.
When the WiFi LED stops blinking, your WiFi device is automatically
connected to the PowerLINE access point and you can surf the web.

10
Add Adapters
To add adapters before you configure the security feature for the network,
just plug them in and connect the adapters to your equipment.
¾To add an adapter to a PowerLINE network with security
set:
1. Plug the adapter into a wall outlet where you want to add Internet
access.
2. If you used a private encryption key, press the Security button on
one of the adapters that is already a part of the network for two
seconds, and then press the Security button on the new adapter for
two seconds.
Both buttons must be pressed within two minutes.
Note: The Security button does not work in power saving mode.
Do not press the Security button on the PowerLINE adapter until
installation is complete and the adapters are communicating with each
other (indicated by the blinking Power LED). Pressing this button too soon
can temporarily disable PowerLINE communication. If this occurs, use the
Factory Reset button to return the PowerLINE adapter to its factory
default settings.