New Classic Furniture ARIES B561-400 User manual

ASSEMBLY INSTRUCTIONS
B561-400 ARIES 4/6 F PANEL BED-HB/FB/RAILS
No ITEM Qty
AHeadboard 1 pc
BFootboard 1 pc
CHeadboard Leg(L&R) 2 pcs
DBed Roll-Out Slats 2 sets
EBed Slats Support 4 pcs
FSide Rail Left 2 pcs
GSide Rail Right 2 pcs
HCenter Slats 2 pcs
ISide Rail Leg 2 pcs
PARTS LIST
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
1 OF 2
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the parts list and/or hardware list shown.
HARDWARE LIST
STEP 1.1 :
4
1
3
4x
STEP 1.2 :
6
BACK VIEW
C C
8x
RIGHT
LEFT
C
A
Attach Head Board Leg ( C ) to Head Board ( A ) as shown using JCBC BOLT( 1 ) with
Flat washer (3)and securing with ALLEN KEY ( 4 ) .
STEP 1.1 :
Fix the other holes with Csk Screw (6) as shown.
STEP 1.2 :
No ITEM Qty
1JCBC M6 x 30mm 12 pcs
2JCBC M6 x 50mm 4 pcs
3
Flat Washer 1/4"ID x
19mmOD Blk 12 pcs
4
ALLEN KEY
m4x65mm Blk
(FOR HB LEG) 1 pc
5
ALLEN KEY
m5x65mm Blk
(FOR SIDE RAIL) 1 pc
6
Flat Head Chipboard
Screw m4x32mm Rbw 32 pcs

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
2 OF 2
leveler
STEP 3.1 :
Push the side rail(F) & (G) meet with wooden
slat(D) and fix the CSK screw (6)
by using the Screw Driver.
24x
STEP 3.2 :
STEP 3.3 :
4x
4
2
D
H
E
E
F
6
D
4
1
3
x8
STEP 2.1 :
A
DO NOT FULLY TIGHTEN SCREW
IN THIS STEP BEFORE ALIGN
THE SIDE RAIL AS SHOWN.
G
F
SIDE VIEW
ALIGN BEFORE TIGHTEN
FRONT VIEW
I
R
L
Right Sticker
Left Sticker
STEP 2.2 :
I
5
G
F
I
F G
I
BF
G
LOOSEN
STEP 3 : Fix the Bed Slat Support (E ), to Bed Slat (D) and Center slats (H) tighten with
JCBC Bolt (2) as shown . Install the bed slat ( D ) to side rail ( F ) & ( G ) and tighten with
Csk Screw ( 6 ) as per diagram shown. (NOTE: THE SETUP MUST DONE AT THE DECIDED
LOCATION FOR THE BED TO OBTAIN PERFECT STABILITY)
Repeat step 3 for other set of slats assembly.
STEP 2.1 : Attach Side Rail ( F ) & ( G ) to the Side Rail Leg ( I ) as shown using JCBC BOLT( 1 )with
Flat washer (3)and securing with ALLEN KEY ( 4 ) by outside side rail (F) & (G) .
STEP 2.2 : Loosen JCBB Bolt at Headboard &Footboard Leg using Allen Key (5) (Do not tighten them before
Hook SET-UPSIDE RAIL TO HEAD BOARD (A) closely and push down to fit and tighten
them accordingly.
Repeat step 2.2 with other end of rail to hook onto FOOTBOARD (B).
TIGHTEN
5