New Classic Furniture D1435-60S User manual

ASSEMBLY INSTRUCTIONS
MILO RECTANGLE DINING TABLE
MILO DINING CHAIR (SET INCLUDES 4 CHAIRS, 1 BENCH)
1
ITEM NO. D1435-60S
This page lists all the contents included in the Box. Please take time to identify the
hardware as well as the individual components to this product. As you unpack and
prepare for assembly, place the contents on a carpeted or padded area to protect
them from damage.
C l e a n i n g & C a r e
Treat the surface with care, clean it with a dry or damp soft cloth.
Do not use abrasive cleaners. Hardware may be loosen over time.
Periodically check that all connections are tight.
A Phillips screwdriver is necessary for assembly.

2
GENERAL INFORMATION, TIPS & TRICKS
2. To avoid damages, assemble this product on a non-abrasive surface such as a carpet.
4. Not for commercial use.
3. Make sure all bolts and nuts are tightly fastened before the product is used.
5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the
wood as needed. Avoid prolonged exposure to moisture.
Please make sure you have all parts before beginning assembly. Please wait
until all steps are completed before tightening bolts. We recommend two
people to assemble.
1. Please read the assembly instructions prior to assembling this product.
Do not put hot pots or objects which are more than
80 degrees Fahrenheit directly on the table.
A Phillips screwdriver is necessary for assembly.

3
QTY: 1 PC
A. Table Top
TABLE PART LIST
QTY: 4 PCS
B. Table Legs
SIZE: 5/16" DIA
3. NUTS
QTY: 8 PCS
1. FLAT WASHERS
QTY: 8 PCS
SIZE: 5/16" DIA
4. ALLEN WRENCH
SIZE: 5/16" DIA
QTY: 1 PC
2. SPRING WASHERS
SIZE: 5/16" DIA
QTY: 8 PCS
TABLE HARDWARE LIST

4
TABLE ASSEMBLY INSTRUCTIONS
STEP 1
Turn the Table Top (A) upside down on a non-abrasive surface such as a
carpet (the underside of the Table Top (A) should be placed face up).
Attach the Table Legs (B) to the corner of the apron of the Table Top (A)
by using Flat Washers (1), Spring Washers (2), Nuts (3), and tighten with
Allen Wrench (4) as per illustration below.
4
B
A

TABLE ASSEMBLY INSTRUCTIONS
Turn the table to the upright position carefully.
Make sure the table is level, and then securely tighten all nuts at this
stage. Assembly is completed.
The table is now ready for use.
STEP 2
5

1. FLAT WASHERS
QTY: 44 PCS
CHAIR PART LIST
SIZE: 5/16" DIA SIZE: 5/16" DIA
CHAIR HARDWARE LIST
QTY: 16 PCS
QTY: 4 PCSQTY: 8 PCS
SIZE: 1/4" x 3"
QTY: 4 PCS
SIZE: 5/16" DIA
3. NUTS
QTY: 16 PCS
6. LONG BOLTS
SIZE: 5/32" x 1 1/2"
6
QTY: 4 PCS
2. SPRING WASHERS
7. WOOD SCREWS5. SHORT BOLTS
SIZE: 1/4" x 1 3/4"
SCP42:YTQ SCP21:YTQ
4. ALLEN WRENCH
SIZE: 5/16" DIA
QTY: 1 PC
D. Cushion SeatsC. Front LegsB. Seat FramesA. Back Legs
QTY: 44 PCS

PLASTIC PLUG.
7
STEP 1
CHAIR ASSEMBLY INSTRUCTIONS
BC
A4
6
2
15
2
1
Turn the chair upright.
Make sure the assembled
unit is level and
square. Tightly fasten all
Nuts (3) and Bolts (5&6)
with the Allen Wrench (4).
STEP 2
Attach the Seat Frame (B) to the Back Leg (A) by using Short Bolts (5),
Long Bolts (6), Spring Washers (2), and Flat Washers (1).
Do not fully tighten.
4
3
2
1
3
2
1
C
3
2
1
B
C
C
Note: The Seat Frame (B) has
two screw holes on each
side, which are used for
attaching the seat. These
holes are wider on the
bottom and narrower on
the top. Ensure the wider
holes face towards you.
Attach the Front Legs (C) to the Seat Frame (B) by using Nuts (3), Spring
Washers (2), and Flat Washers (1).

7
CHAIR ASSEMBLY INSTRUCTIONS
7
Place the assembled chair frame on the Cushion Seat (D).
Attach with Wood Screws (7). Tighten the screws.
77
7
7
A
C
8
Hint: Protect the non-abrasive table surface and the Cushion Seat (D) by laying a towel
in-between the chair seat and table.
Place the Cushion Seat (D) upside down on a non-abrasive table
surface. The rear (tapered end) of the Cushion Seat (D) should be
near the table edge.
STEP 3
D

9
CHAIR ASSEMBLY INSTRUCTIONS
Repeat Steps 1 to 3 to assemble the other chairs.
STEP 4
The Dining Chair is now ready for use.
Printed in Vietnam

10
BENCH HARDWARE LIST
QTY: 1 PC
C. Seat Frame
QTY: 4 PCS
B. Front Legs
SIZE: #8 x 1 1/2" L
3. NUTS
QTY: 8 PCSQTY: 8 PCSQTY: 8 PCS
QTY: 8 PCS
5. WOOD SCREWS
4. ALLEN WRENCH
QTY: 1 PC
A. Cushion Seat
BENCH PART LIST
SIZE: 5/16" DIA
QTY: 1 PC
1. FLAT WASHERS 2. SPRING WASHERS
SIZE: 5/16" DIA SIZE: 5/16" DIA SIZE: 5/16" DIA

11
Place the assembled bench frame on the Cushion Seat (A).
Attach with Wood Screws (5). Tighten the screws.
Place the Cushion seat (A) upside down on a non-abrasive table surface.
The rear (tapered end) of the Cushion Seat (A) should be near the table
edge.
Hint: Protect the non-abrasive table surface and the cushion seat (A) by laying a towel
in-between the chair seat and table.
Attach the Front Legs (B) t o the Seat Frame (C) by using Nuts (3), Spring
Washers (2), and Flat Washers (1).
Note: The Seat Frame (C) has
two screw holes on each
side, which are used for
attaching the seat. These
holes are wider on the
bottom and narrower on
the top. Ensure the wider
holes face towards you.
BENCH ASSEMBLY INSTRUCTIONS
STEP 2
STEP 1
B
B
C
A
B
C
1
2
3
4
1
2
3
5
B
B
B

12
BENCH ASSEMBLY INSTRUCTIONS
The bench is now completed and ready for use.
Printed in Vietnam
STEP 4