New Classic Furniture ARIES B561-500 User manual

ASSEMBLY INSTRUCTIONS
B561-500 ARIES 3/3 T PANEL BED-HB/FB/RAILS
No ITEM Qty
AHeadboard 1 pc
BFootboard 1 pc
CHeadboard Leg(L&R) 2 pcs
DBed Roll-Out Slats 2 sets
ESide Rail Left 2 pcs
FSide Rail Right 2 pcs
GSide Rail Leg 2 pcs
PARTS LIST
Attach Head Board Leg ( C ) to Head Board ( A ) as shown using JCBC BOLT( 1 )with
Flat washer (2)and securing with ALLEN KEY ( 3 ) .
STEP 1.1 :
Fix the other holes with Csk Screw (5) as shown.
STEP 1.2 :
STEP 1.1 : STEP 1.2 :
5
BACK VIEW
C C
8x
RIGHT
LEFT
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
1 OF 2
C
A
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the parts list and/or hardware list shown.
No ITEM Qty
1JCBC M6 x 30mm 12 pcs
2
Flat Washer 1/4"ID x
19mmOD Blk 12 pcs
3
ALLEN KEY
m4x65mm Blk
(FOR HB LEG) 1 pc
4
ALLEN KEY
m5x65mm Blk
(FOR SIDE RAIL) 1 pc
5
Flat Head Chipboard
Screw m4x32mm Rbw 32 pcs
HARDWARE LIST
3
1
2
4x

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
2 OF 2
STEP 2.1 :
STEP 2.1 :
Attach Side Rail ( E ) & ( F ) to the Side Rail Leg ( G ) as shown using
JCBC BOLT( 1 )with Flat washer (2)and securing with ALLEN KEY ( 3 )
by outside side rail (E) & (F) .
STEP 2.2 : Loosen JCBB Bolt at Headboard & Footboard Leg using Allen Key (4) (Do not tighten them before
Hook SET-UPSIDE RAIL TO HEAD BOARD(A) closely and push down to fit and tigthen
them accordingly.
Repeat step 2.2 with other end of rail to hook onto FOOTBOARD (B).
A
DO NOT FULLY TIGHTEN SCREW
IN THIS STEP BEFORE ALIGN
THE SIDE RAIL AS SHOWN.
F
E
SIDE VIEW
ALIGN BEFORE TIGHTEN
FRONT VIEW
G
R
L
Right Sticker
Left Sticker
STEP 2.2 :
8x
G
4
F
E
G
E F
G
BE
F
STEP 3 : Install the bed slat support ( D ) to side rail ( E ) & ( F ) and tighten with Csk Screw ( 5 )
as per diagram shown. (NOTE: THE SETUP MUST DONE AT THE DECIDED LOCATION
FOR THE BED TO OBTAIN PERFECT STABILITY)
Repeat step 3 for other set of slats assembly.
Push the side rail(E) & (F) meet with wooden
slat(D) and fix the CSK screw (5)
by using the Screw Driver.
24x
STEP 3.1 : E
5
D
3
1
2
x8
4