New Classic Furniture D1701-50S User manual

1
ASSEMBLY INSTRUCTIONS
GIA ROUND DINING TABLE
GIA DINING CHAIR (SET INCLUDES 4 CHAIRS)
ITEM NO. D1701-50S
This page lists all the contents included in the Box. Please take time to identify the
hardware as well as the individual components to this product. As you unpack and
prepare for assembly, place the contents on a carpeted or padded area to protect
them from damage.
C l e a n i n g & C a r e
Treat the surface with care, clean it with a dry or damp soft cloth.
Do not use abrasive cleaners. Hardware may be loosen over time.
Periodically check that all connections are tight.
A Phillips screwdriver is necessary for assembly.

Please make sure you have all parts before beginning assembly. Please wait
until all steps are completed before tightening bolts. We recommend two
people to assemble.
5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the
wood as needed. Avoid prolonged exposure to moisture.
3. Make sure all bolts and nuts are tightly fastened before the product is used.
4. Not for commercial use.
2. To avoid damages, assemble this product on a non-abrasive surface such as a carpet.
1. Please read the assembly instructions prior to assembling this product.
GENERAL INFORMATION, TIPS & TRICKS
2
Do not put hot pots or objects which are more than
80 degrees Fahrenheit directly on the table.
A Phillips screwdriver is necessary for assembly.

QTY: 4 PCS
SIZE:
QTY:
QTY: 1 PC QTY: 4 PCS QTY: 4 PCS
B. Connector Panels C. Middle Shelf D. Table Legs
TABLE PART LIST
A. Table Top
QTY: 1 PC
3
TABLE HARDWARE LIST
QTY: 16 PCS16 PCS
SIZE: 5/16" DIA5/16" DIA
2.SPRING WASHERS1.
5.
SIZE: 5/16” x 1 1/4”
3.FLAT WASHERS LONG BOLTS
QTY: 4 PCS
SIZE: 5/16" DIA
4.
ALLEN KEY
QTY: 8 PCS
SIZE: 1/4” DIA
QTY: 1 PC QTY: 8 PCS
SIZE: 1/4” x 1”
7. SHORT BOLTS6. SHORT BOLTS
SIZE: 5/16” x 2 1/2”
LEVELERS

STEP 1
Attach the Connector Panels (B) to the Table Legs (D) by using Long Bolts (3).
Tighten by using Allen Key (5).
Attach the Table Legs (D) to the Table Top (A) by using Short Bolts (6) with
Allen Key (5). Do not tighten all bolts at this step.
Attach Middle Shelf (C) to the Table Legs (D) by using Short Bolts (7), Spring
Washers (1), and Flat Washers (2) with Allen Key (5). Do not tighten all bolts
at this step.
TABLE ASSEMBLY INSTRUCTIONS
STEP 2
4
3
5
5
6
6
1
2
7
5
6
6
6
6
1
2
7
76
6

T
Attach the Levelers (4) to the base of the Table Legs (D) in clockwise
direction.
urn the table to the upright position carefully.
Make sure the table is level, and then securely tighten all bolts at this
stage. Assembly is now completed.
STEP 3
STEP 4
TABLE ASSEMBLY INSTRUCTIONS
5
4
4
44
4

QTY: 4 PCSQTY: 4 PCS
SIZE: 5/16" DIA
2. SPRING WASHERS
QTY: 4 PCS
SIZE: 1/4" x 3"
1. FLAT WASHERS
CHAIR HARDWARE LIST
QTY: 44 PCS QTY: 44 PCS QTY: 16 PCS
A. Back Legs
SIZE: 5/16" DIA
QTY: 1 PC
SIZE: 5/16" DIA
4. ALLEN WRENCH3. NUTS
QTY: 16 PCSQTY: 12 PCS
SIZE: 1/4" x 1 3/4"
5. SHORT BOLTS 6. LONG BOLTS 7. WOOD SCREWS
QTY: 8 PCS
CHAIR PART LIST
D. Cushion Seats
QTY: 24 PCS
SIZE: 5/32" x 1 1/2"
B. Seat Frames C. Front Legs
SIZE: 5/16" DIA
6

PLASTIC PLUG.
CHAIR ASSEMBLY INSTRUCTIONS
2
Note: The Seat Frame (B) has
two screw holes on each
side, which are used for
attaching the seat. These
holes are wider on the
bottom and narrower on
the top. Ensure the wider
holes face towards you.
C
C
B
1
2
3
C
7
3
1
2
Attach the Seat Frame (B) to the Back Leg (A) by using Short Bolts (5),
Long Bolts (6), Spring Washers (2), and Flat Washers (1).
Do not fully tighten.
STEP 2
Turn the chair upright.
Make sure the assembled
unit is level and
square. Tightly fasten all
Nuts (3) and Bolts (5&6)
with the Allen Wrench (4).
B
A
1
C
5
4
6
2
1
1
Attach the Front Legs (C) to the Seat Frame (B) by using Nuts (3), Spring
Washers (2), and Flat Washers (1).
2
3
4
STEP 1

Place the assembled chair frame on the Cushion Seat (D).
Attach with Wood Screws (7). Tighten the screws.
Hint: Protect the non-abrasive table surface and the Cushion Seat (D) by laying a towel
in-between the chair seat and table.
Place the Cushion Seat (D) upside down on a non-abrasive table
surface. The rear (tapered end) of the Cushion Seat (D) shoule be
near the table edge.
STEP 3
7
7
7
7
7
7
D
C
A
CHAIR ASSEMBLY INSTRUCTIONS
8

CHAIR ASSEMBLY INSTRUCTIONS
9
Repeat Steps 1 to 3 to assemble the other chairs.
STEP 4
Printed in Vietnam
The Dining Chair is now ready for use.