New Classic Furniture D5524-20 User manual

Assembly Instructions
MADE IN VIETNAM PAGE: 1 OF 3
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the PARTS LIST and/or HARDWARE LIST shown below.
Please read the instructions thoroughly before assembly.
ITEM NO. D5524-20
FLAIR DINING CHAIRS
1.We recommend that you assemble this product with the assistance of another person; this will make the
assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
2.Please do not tighten screws or bolts until the assembly is completed.
3. To level the chairs or table, before tightening all the screws, the chairs or table must be placed on a
flat surface and then tighten the screws.
4.Please put all parts on a non-abrasive floor before assembly and follow the assembly steps to assemble
your newly purchased product correctly and efficiently.
PARTS LIST HARWARE LIST
NO.
1FLAT WASHER
1/4” DIA.
LONG BOLT
1/4” x 3”
COMPONENT SKETCH QTY
2
3
4
5
8 PCS
6 PCS
8 PCS
6
SHORT BOLT
1/4” x 1 9/16”
22 PCS
22 PCS
1 PC
7
WRENCH
( 4mm )”
ALLEN
SPRING
WASHER
1/4” DIA.
MEDIUM BOLT
1/4” x 2 3/8”
WRENCH
( 4mm )”
ALLEN
WOOD SCREW
1/4” x 1 9/16” 8 PCS
(2 PCS/CTN)
A
COMPONENT
CHAIR BACK
B SEAT 2PCS
C1 2PCS
SKETCH QTY
2PCS
NO.
2PCS
D1
2PCS
D2
C2 2PCS
RIGHT SIDE
FACING (RSF)
LEG
LEFT SIDE
FACING (LSF)
LEG
RIGHT SIDE
FACING (RSF)
STRETCHER
LEFT SIDE
FACING (LSF)
STRETCHER

MADE IN VIETNAM PAGE: 2 OF 3
Assembly Instructions
To assemble the chairs, please follow the following steps and repeat for each chair:
ITEM NO. D5524-20
(2 PCS/CTN)
STEP 3 STEP 4
STEP 2
A
B
2
1
4
6
C1 (Right)
C2 (Left)
D1 (Right)
D2 (Left)
A
B
7
7
7
7
STEP 1
Install both RSF Stretcher (D1) and LSF Stretcher (D2)
to chair back (A) and front legs (C1) and (C2) by using
a screw driver with hardware 7.
*Attention: DO NOT TIGHTEN THE SCREWS
Assemble the front legs (C1) and ( C2) with the seat (B) by
using Allen Wrench (6) with hardware 1,2, and 4.
*Attention: DO NOT TIGHTEN THE BOLTS
To level the chair, stand the chair up on a flat surface and
tighten all the bolts by using Allen Wrench (6) and tighten all
the screws by using a screw driver.
Place the chair back (A) on a soft and clean surface.
Assemble the seat (B) with the chair back (A) by using Allen
Wrench (6) with hardware 1,2, and 3 . Then assemble the seat
(B) with the back legs of the chair back (A) using Allen Wrench
(6) with hardware 1,2, and 5
*Attention: DO NOT TIGHTEN THE BOLTS.
1 2 5
6
6
1
2
3
BA
*Please use short bolt
FLAIR DINING CHAIRS

MADE IN VIETNAM PAGE: 3 OF 3
Assembly Instructions
STEP 5
Repeat STEP 1 through STEP 4 to assemble the other chair.
Fully Assembled Chair
ITEM NO. D5524-20
(2 PCS/CTN)
FLAIR DINING CHAIRS