Living Spaces Boswell E User manual

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in headboard carton to attach bed feet .
1 2
Step#1
Retrieve bed feet from carton fastened behind the headboard.
Attach bed feet (F) to the headboard using Wrench (I), Bolt (R) and Washer (E).
Step#2
Attach bed feet (F) to the side rails using Wrench (I), Bolt (R) and Washer (E).
E F I R
Φ8 MM H=10CM Φ8*70 MM
8PCS 4PCS 1PC 8PCS
Boswell E/C King Storage bed Assembly

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in side rails carton to attach center support system..
3 4
Step#3
Attach side rails to headboard using Wrench(I), Bolt (B) and Washer (E)(factory installed).
Attach Metal support beam (U) to side rails using Wrench (I), Bolt (A1) and Washer (E)
(factory installed).
Step#4
Attach center support rails (O) to the Headboard using Wrench (I), Bolt (B) and Washer
(E).(factory installed).
Attach center support rails (O) to the Metal support beam (U) using Wrench (I), Bolt
(L) ,Washer (E) and Nut (Z). Tighten/secure center support rail with Wrench (Y) .
D E I J L M N O P U Y Z
Φ6 MM Φ8 MM Φ8 MM H=27CM Φ8*50MM Φ6*40MM
5PCS 4PCS 1PC 5PCS 4PCS 5PCS 26PCS 2PCS 39PCS 1PC 1PC 4PCS
Boswell E/C King Storage bed Assembly
*Bolt A1 and Washer E
are factory installed*
*Bolt B and Washer E
are factory installed*
*Bolt B and
Washer E are
factory installed*

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in side rails carton to attach center support system.
6 7
Step#5
Locate bed in final position before attaching center supports.
Step#6
Attach center support legs (J) to the Center support rails (O) using Wrench (I), Bolt (M) and
Washer (D).
Attach center support leg (J) to the Metal support beam (U) using Wrench (I), Bolt (M) and
Washer (D).
Step#7
(IMPORTANT:Make sure slats are inserted into center clip BEFORE snapping into place)
Verify Euro Slats System Tension Slats are installed curved upwards per diagram.
Insert tension slats into center clip (N) and factory installed End clip (Q) before snapping
into place.
D E I J L M N O P U Y Z
Φ6 MM Φ8 MM Φ8 MM H=27CM Φ8*50MM Φ6*40MM
5PCS 4PCS 1PC 5PCS 4PCS 5PCS 26PCS 2PCS 39PCS 1PC 1PC 4PCS
Boswell E/C Kin
g
Stora
g
e bed Assembl
y
*Clip Q are factory
installed*

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
Hardware included in storage drawer carton.
8 9
Step#8
Attach casters (H) to the drawer using Wrench (I), Bolt (A) and Washer (D).
Step#9
Attach drawers to the footboard using Wrench (I), Bolt (B) and Washer (E)(factory installed).
Drawers attach 1" below bottom of footboard.
A D I H
Φ6*15MM Φ6 MM Φ8 MM H=8 CM
16PCS 16PCS 1PC 8PCS
Boswell E/C Kin
g
Stora
g
e bed Assembl
y

CONGRATULATIONS ON YOUR NEW BED PURCHASE
~Warning：do not move bed after final assembly as it may result in damages to floor and/or bed.~
10
Step#10
Insert/Roll the drawer under the bed.
Factory installed guide rail keeps drawer centered.
Boswell E/C Kin
g
Stora
g
e bed Assembl
y
*Factory installed guide rail keeps drawer centered*