Next BARLOW BOOKCASE 804833 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
warping.
• All assembly fixings should always be tightened properly
and periodically check all fixings and tighten if necessary.
• Made from particleboard,MDF with a wood effect finish.
• Made in Indonesia.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
PRODUCT INFORMATION
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Ensure the mats and coasters used do not have an abrasive surface underneath.
804833 BARLOW BOOKCASE
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
1 of 12

15x12 mm. 7.5X32 mm. P6x30 mm. 8x32 mm. F6x13 mm.
FITTINGS
Ax16 Bx16 Cx1 Dx23 Ex24 Fx12
P4x12 mm. 6x40 mm. F4x19 mm. T-35 Curve P4x15 mm. 25x30 mm.
Gx6 Hx20 Ix20 Jx4 Kx2 Lx2
P6X19 mm. F6x31 mm. 150 mm. 20x9 mm. 1793 mm. 4 mm
Mx2 Nx3 Ox2 Px2 Qx2 Rx2
6x1 7x2 8x1 9x1 10x3 11x1 12Lx1 12Rx1
PARTS
1x1 2x1 3Lx1 3Rx1 4x1 5x1
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
2 of 12

- Attach 4x cambolts (B) into the holes of panel 1.Tighten
with a cross blade screwdriver.
Recommend to use cross-blade screwdriver.
- Insert 4x camlocks (A) into the holes of panel 2 and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Insert 4x wooden dowels (D) into the holes of panel 2.
- Insert 1x wooden dowel (D) into the holes of panel 11.
- Insert 2x camlocks (A) into the holes of panel 3R and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Attach 6x cambolts (B), 2x wooden dowels (D) into the
holes of panel 3R.
Recommend to use cross-blade screwdriver.
STEP TWO
STEP ONE
STEP THREE
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
3 of 12

- Insert 2x camlocks (A) into the holes of panel 3L and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Attach 6x cambolts (B), 2x wooden dowels (D) into the
holes of panel 3L.
Recommend to use cross-blade screwdriver.
- Insert 2x wooden dowels (D) into the holes of panel 4.
- Insert 2x camlocks (A) into the holes of panel 5 and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Insert 4x wooden dowels (D) into the holes of panel 5.
- Insert 2x door stoppers (P) into the holes of panel 5 and
tighten with a screwdriver.
STEP FOUR
STEP FIVE
STEP SIX
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
4 of 12

- Insert 2x camlocks (A) into the holes of panel 6 and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Insert 4x camlocks (A) into the holes of panel 9 and
ensure that arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
- Insert 8 x wooden dowels (D) into the holes of panel 6 and
9.
- Attach panel 11 to panel 2 by tightening 1x screw (C)
clockwise with a cross-blade screwdriver.
- Attach panel 2, 5, 6 and 9 to the panel 3R by tightening 7 x
camlocks (A) clockwise with a flat-blade screwdriver.
Recommend to use flat-blade screwdriver.
STEP SEVEN
STEP EIGHT
STEP NINE
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
5 of 12

- Insert panel 10 (x3) to the recessed grooves of panel 2 and
3R and ensure that the arrow mark is positioned as shown
in the diagram and insert 2x backboard "H" bar (Q) between
panel 10.
- Attach panel 3L to the assembled unit by tightening 7 x
camlocks (A) clockwise with flat-blade screwdriver.
Recommend to use flat-blade screwdriver.
STEP ELEVEN
STEP TEN
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
6 of 12

STEP TWELVE
- Carefully lift the unit upright. (This should be lifted using 2
people.)
- Attach panel 1 to the assembled unit by tightening 4 x
camlocks (A) clockwise with flat-blade screwdriver.
Recommend to use cross-blade screwdriver.
- Attach 6x screws (G) into the holes of panel 10(x3) and
tightening with a cross-blade screwdriver.
- Attach 20x back board fasteners (H) to the backboard
grooves and secure by tightening 20x screws ( I ) clockwise
with a cross-blade screwdriver.
Recommend to use cross-blade screwdriver.
STEP THIRTEEN
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
3R
2
9
10
10
1
10
10
3L
10
7 of 12

- Attach panel 4 to assembled unit by tightening 3x screws
(N) clockwise with a cross-blade screwdriver.
Recommend to use cross-blade screwdriver.
- Insert 12x shelf support (F) into the holes of panel 3R and
3L.
STEP FOURTEEN
STEP FIVETEEN
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
8 of 12

- Put panel 7 (x2) and panel 8 to assembled unit.
- Attach 2x hinges (J) to the holes of panel 12L and secure
by tightening 4x screws (E) clockwise with a
screwdriver.
- Attach 1x handle (L) to the holes of panel 12L and secure
by tightening 1x screw (K) clockwise with a
screwdriver.
- Attach 2x hinges (J) to the holes of panel 12R and secure
by tightening 4x screws (E) clockwise with a
screwdriver.
- Attach 1x handle (L) to the holes of panel 12R and secure
by tightening 1x screw (K) clockwise with a
screwdriver.
Recommend to use cross-blade screwdriver.
STEP SEVENTEEN
STEP SIXTEEN
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
9 of 12

- Attach panel 12R and 12L to assembled unit and
tightening 8 x screws (E) clockwise with a cross-blade
screwdriver until tight.
(For adjust the hinge, look the diagrams)
STEP NINETEEN
- Attach 2x wall brackets (O) to the panel 1 and using 2x
washer (R) and secure by tightening 2 x screws (M)
clockwise with a cross blade screwdriver until tight.
STEP EIGHTEEN
1
11
2
3R
3L
4
5
5
6
9
11
2
3R
3R
9
95
6
2
3R
10
10
10
2
9
10
10
10
2
3L
9
3R
10 9
10
10
3L
2
5
2
3L
6
10
10
3R
1
3R
1
10
3R
12L
12R
3R
12L
8
2
5
7
3L
6
7
1
12R
2
3R 9
10
10 10
3L
1
10 of 12