New Classic Furniture HUDSON D3832-42-CTR User manual

Assembly Instructions
MADE IN VIETNAM PAGE: 1 OF 3
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the PARTS LIST and/or HARDWARE LIST shown below.
Please read the instructions thoroughly before assembly.
1. We recommend that you assemble this product with the assistance of another person; this will make the
assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
2. Please do not tighten screws or bolts until the assembly is completed.
3. To level the chairs or table, before tightening all the screws, the chairs or table must be place on a flat
surface and then tighten the screws.
4.Please put all parts on a non-abrasive floor before assembly and follow the assembly steps to assemble
your newly purchased product correctly and efficiently.
ITEM NO. D3832-42-CTR
HUDSON 42" ROUND COUNTER TABLE
& 4 CHAIR SET
PARTS LIST
NO.
A
COMPONENT
CHAIR BACK
SKETCH QTY.
4 PCS
B4 PCS
C2 FRONT LEG
(LEFT) 4 PCS
D1
SIDE
STRETCHER
(RIGHT)
4 PCS
FRONT LEG
(RIGHT)
EFRONT
STRETCHER 4 PCS
D2
SIDE
STRETCHER
(LEFT)
4 PCS
C1
CUSHION
SEAT
4 PCS
NO.
1FLAT WASHER
5/16” DIA.
SPRING
WASHER
5/16” DIA.
HARDWARE LIST
COMPONENT SKETCH QTY.
44 PCS
244 PCS
NUT
5/16” DIA.
ALLEN
WRENCH
5/16” DIA.
316 PCS
41 PC
LONG BOLT
1/4” x 3”
616 PCS
WOOD SCREW
#8 x 1 1/2”
724 PCS
SHORT BOLT
1/4” x 1 3/4”
512 PCS

MADE IN VIETNAM PAGE: 2 OF 3
Assembly Instructions
STEP 3
Install front stretcher into the holes of the front
legs then attached to the cushion seat.
STEP 4
Complete..
To assemble the chairs, please follow the following steps and repeat for each chair:
STEP 1
Lay the chair back on soft clean surface and
install the cushion seat.
STEP 2
Insert side stretchers with wood screws.
ITEM NO. D3832-42-CTR
HUDSON 42" ROUND COUNTER TABLE
& 4 CHAIR SET
21
5
4
6
4
21
B
A
A
E1 (Right)
7
E2 (Left)
7
B
7
7
1234
A
B
C2 (Left)
D1 (Right)
C1 (Right)
D2 (Left)
7
E
7

MADE IN VIETNAM PAGE: 3 OF 3
Assembly Instructions
NO.
1FLAT WASHER
5/16” DIA.
HARDWARE LIST
COMPONENT SKETCH QTY.
8 PCS
2SPRING WASHER
5/16” DIA. 8 PCS
3BOLT
5/16” x 65 MM 8 PCS
4ALLEN KEY
4 MM 1 PC
NO.
A
PARTS LIST
COMPONENT
TABLE TOP
SKETCH QTY.
1 PC
BTABLE LEG 4 PCS
To assemble the table, please follow the following
steps:
STEP 1: Install 4 of the table legs and tighten all
bolts.
4
3 2 1
B
A
ITEM NO. D3832-42-CTR
HUDSON 42" ROUND COUNTER TABLE
& 4 CHAIR SET
B
B
B
UP DOWN
ADJUSTABLE
LEVELER