New England Arbors 102515 User manual

Check Box for These Contents
In the event of damaged, missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri.8:00 AM to 4:00 PM EST).
1. Corner Post (1) 3” x 3” x 43”
2. Top Rails (2) 1 1/2” x 1 1/2” x 44.73”
3. End Post (2) 3” x 3” x 38”
4. 18”Pickets (6) 7/8” x 3” x 18”
5. 19”Pickets (2) 7/8” x 3” x 19”
6. Bottom Rails (2) 1 1/2” x 1 1/2” x 44.73”
7. 20 1/2”Pickets (2) 7/8” x 3” x 20 1/2”
8. 23”Pickets (2) 7/8” x 3” x 23”
Optional Materials
3 Bags of pre-mix concrete for extra post stability.
Tools You Will Need
• Shovel
• Tape measure
General Information
Read Instructions through carefully before
beginningassembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10 ft. x 8 ft. for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Country Corner Picket
Please readthrough before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOURPOSTS FOR ALL MATERIALS.
ASSEMBLY INST RUCTION S
1
43.7 in
110.9 cm
Ver 2.1/102515
7
5
4
3
1
2
8
6
38.7 in
98.2 cm
42.5 in
108.0 cm
48.9 in
124.1 cm
www.newenglandarbors.com

2
Layout the corner post.
Insert the top rail (holes on both sides of rail) into the top hole on
corner post ensuring that the holes in the rail are facing the other
hole in the corner post. This is critical to ensure proper orientation
for ultimately inserting pickets.
Insert the bottom rail (holes on one side) into the bottom hole
on corner post. Ensure that holes in the rail are facing the other
hole in the corner post.
Repeat steps 1 and 2 for the remaining top and bottom rails as
illustrated in the remaining two holes on the other side of the
corner post.
Insert the remaining open railends into the two end posts andpush
past the locking tabs to create the“frame” of your corner picket.
Determine the desired location for your cornerpicket, and dig
three 12”deep holesusing the distances as illustrated. Set the
completed“frame”into the holes and check each rail for level.
At this time, you may need to adjust the depths of the holes.
Use alevel to check each post andonce you are satisfied withthe
orientation,fill in the holes (cement is optional, but recommended).
Starting with the 23”pickets, slip each one down through the
top rail and into the bottom rail on either side of the corner post.
Note: The tabs on the endof the pickets go into the bottom rail.
As in step 6, slip each of the remaining pickets through the next
five holes on either side of the corner post. Insert the pickets in
decending order, ending with three 18” pickets on each side.
Country Corner Picket
Assemble the Post and Frame
2
3
1
13
4
4
5
6
7
86
7 8
42.5 in
108.0 cm
48.9 in
124.1 cm
5
12 in
30.5 cm
Level
Assemble the Pickets
Once rails are inserted into holes and pushed past locking
tabs they will LOCKINTO PLACE PERMANENTLY.
2
Holes on
Both Sides
of Top Rail
Locking
Tab
*
*
Once pickets are inserted into holes and pushed past
locking tabs they will LOCKINTO PLACE PERMANENTLY.
*
*