New Holland E385 Instruction manual

NEW HOLLAND KOBELCO CONSTRUCTION MACHINERY S.p.A. - Product Support
Print No. 604.13.679
Edition - January 2006
WORKSHOP MANUAL
All the information and data contained in this manual are based upon most recent information available at the
time of its publication.
NEW HOLLAND KOBELCO has the right to implement, at any time, any modification without providing any
communication.
R0077
E385
(Tier 3)
Find manuals at https://best-manuals.com

Find manuals at https://best-manuals.com

E385 IN-1
INTRODUCTION
TO THE READER
• This manual is written for an experienced techni-
cian to provide technical information needed to
maintain and repair this machine.
- Besuretothoroughlyreadthismanualforcorrect
information concerning the service procedures.
- If you have any questions or comments, or if you
found any errors regarding the contents of this
manual, please contact:
NEWHOLLANDKOBELCO
CONSTRUCTION MACHINERY S.p.A.
Strada Settimo, 323
San Mauro Torinese (TO)
10099 ITALIA
PRODUCT SUPPORT
Fax. ++39 011 0077357
ADDITIONAL REFERENCES
• Pleaserefertothematerialslistedbelowinaddition
to this service manual:
-OperationandMaintenanceInstructionManual
-PartsCatalog
WORKSHOP MANUAL COMPOSITION
- The “Operational Performance Test” part includes
the information needed to carry out the machine
operationalperformancetest.
- The “Troubleshooting” part includes the technical
information needed for troubleshooting and mal-
function detection.
- The “Repair Instruction” part includes information
neededformaintenanceandrepairofthemachine,
tools and devices needed for maintenance and
repair, maintenance standards, removal/installa-
tion and assembly/disassembly procedures.
• The Workshop Manual consists of five parts:
-“SafetyPrecautions”
-“OperationalPrinciple”
-“OperationalPerformanceTest”
-“Troubleshouting”
-“Repair Instructions”
- The “Safety Precaution” part includes the recom-
mendedproceduresthat,iffollowed,canavoidthe
risk of accident for operator and for staff related to
the work and maintenance machine operations.
- The“OperationalPrinciple”partincludesthetechni-
cal information concerning the operation of main
devices and systems.
Find manuals at https://best-manuals.com

IN-2 E385
INTRODUCTION
To To
Quantity convert Into Multiply by Quantity convert Into Multiply by
from (SI) (Others) from (SI) (Others)
Lenght mm in 0.03937 Pressure MPa kgf/cm210.197
mm ft 0.003281 MPa psi 145.0
L US gal 0.2642 Power kW CV-PS 1.360
Volume L US qt 1.057 kW HP 1.341
m3yd31.308 Temperature °C °F °C x 1.8 + 32
Mass kg lb 2.205 Velocity km/h mph 0.6214
Force N kgf 0.10197 min-1 rpm 1.0
N lbf 0.2248 Flow rate L/min US gpm 0.2642
Torque N.m kgf.m 0.10197 mL/rev cc/rev 1.0
N.m lbf.ft 0.7375
PAGE NUMBER
• Each page has a number, located on the external upper corner of the page. Each page number contains the
following information:
Example: T 1-2-3
Consecutive page number for each group
Group number (if exist)
Section number
T: Technical Manual
W: Workshop Manual
SYMBOLS
In this manual, the following safety alert symbol and signal words are used to alert the reader to the potential for
personal injury or machine damage.
This is the safety alert symbol.
When you see this symbol, be alert to the potential for personal injury.
Never fail to follow the safety instructions prescribed along with the safety alert symbol.
The safety alert symbol is also used to draw attentio in to component/part weights.
To avoid injury and damage, be sure to use appropriate lifting techniques and equipment when lifting heavy
parts.
UNITS USED
SI Units (International System of Units) are used in this manual.
MKSA system units and English units are also indicated in parentheses just behinds SI units.
Example: 24.5 MPa (250 kgf/cm2)
A table for conversion from SI units to other system units is shown below for reference purposes.
Find manuals at https://best-manuals.com