New Star Neomounts FPMA-HAC100 User manual

INSTRUCTION MANUAL
WWW.NEOMOUNTS.COM
FPMA-HAC100HC
EN
NL
DE
FR
IT
ES
PT
DK
NO
SE
FI
PL
CS
SK
RO
Medical mount
Medische steun
Medizinische Halterung
Support médical
Supporto medico
Soporte médico
Suporte medico
Medicinsk beslag
Medisinsk feste
Medicinskt fäste
Medical teline
Uchwyt medyczny
Držák pro lékařské účely
Držiak na lekárske vybavenie
Suport medical
FPMA-HAC100

3
2
INDEX
FPMA-HAC100HC
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
1-6 kg |
2,2-13,2 lbs
6-12 kg |
13,2-26,5 lbs
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
75x75 -
100x100 mm
75x75 -
100x100 mm
1. (x1)
2. (x1)
3. M4x12 (x4)
4. M6x30 (x4)
5. M4x25 (x4)
6. (x4)
7. 2,5 mm (x1)
8. 4 mm (x1)
9. (x2)
10. (x1)
11. (x1)
12. (x1)
13. (x4)
Before starting assembly p. 2
Parts p. 3
Arm operation p. 4
Positioning p. 5
Serviceable range p. 6
Ceiling assembly p. 7
Cable assembly p. 13
Monitor assembly p. 17
Placement of the arm covers p. 19
Adjustment for loading p. 20
Adjusting universal joint tension p. 21
Safety notes p. 22
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
Screen size
VESA
Weight capacity
Tilt
Swivel
Rotate
Height
Depth
Gas spring
Curved screen compatible
Quick-release VESA
Top-x clamp
180° lock system
Handlebar
Crossbar
Cable management
0-170 cm
0-170 cm
0-189 cm
0-189 cm
BEFORE STARTING ASSEMBLY
• Please read this manual thoroughly, before assembling the product.
• Some drawings are enlarged to clearify the steps.
• Do not discard any of the packaging until you have checked all the parts.
• If you are missing any of the parts, please contact your supplier.
Note
Only if required, all fastening hardware can be replaced by the installer at their own risk, based on the requirements of the ceiling
composition; Neomounts shall not be held liable if any fasterning hardware supplied by third parties fails to sufciently secure the ceiling
mount to the ceiling.
Cleaning recommendations
• Please use non-abrasive or diluted products to clean the plastic components of this product, such as soap water or diluted alcohol.
• Use a soft cloth with 91% isopropyl alcohol to remove pen or marker spots on the surface of the arm.
• For any other stains like iodine spots, a soft cloth with above cleansers is suggested for cleaning.
• The following chemicals are strictly forbidden to use cleaning the arm: abrasive cleansers, acetone, mineral spirits, paint thinner or any
other harsh or toxic chemicals.
THE INSTALLATION SHOULD BE PERFORMED BY A QUALIFIED TECHNICIAN AND SHOULD MEET THE
REQUIREMENTS OF LOCAL REGULATIONS
PARTS
14. (x1)
15. (x4)
16. (x2)
17. (x1)
18. 17 mm (x2)
19. 3 mm (x1)
20. (x1)
21. (x2)
22. (x4)
23. (x2)
24. (x1)
25. M5x10 mm (x2)
26. M5x8 mm (x2)
27. (x1)
FPMA-HAC100 FPMA-
HAC100:
FPMA-
HAC100HC:

4 5
POSITIONINGARM OPERATION
Right view
Unit: mm
SOLID RC WALL

67
SERVICEABLE RANGE CEILING ASSEMBLY
Range at +20O- Top view
Unit: mm
Range at -60O- Top view
Unit: mm
NOTE: use level gauge or protractor to help the wall
mount installation
SOLID RC WALL
SOLID RC WALL
SOLID RC WALLSOLID RC WALL
SOLID RC WALL SOLID RC WALL SOLID RC WALL
Unit: mm
If the wall plate is
not levelled after
installation on the
wall, please use
washers to ll the
space in between
the wall plate and
wall.
90O ± 1O

89
STEP 1
Install the ceiling mount rmly to a solid ceiling
1. Disassemble the ceiling mount and the adjustable pole.
2. Choose the exact place you want to x the ceiling mount on the ceiling and mark the drill holes.
3. Drill 4 expansion bolts into the ceiling and place the 4 holes of the ceiling mount into the 4 expansion bolts.
Recommended drill bit size: diameter Ø2,7 mm/ depth 60 mm ±20
4. Lock the bolts with 4 washers and 4 nylon nuts.
STEP A
Install the ceiling cover
If the upper pole hangs below a suspended ceiling, remove the ceiling cover spacer and push the ceiling cover up to the ceiling. Insert the
two screws using the supplied Allen key to secure.
STEP B
Install the ceiling cover
If the lower pole hangs below a suspended ceiling, push the ceiling cover with ceiling cover spacer up to the ceiling. Insert the two screws
using the supplied Allen key to secure.
Push the ceiling cover
up to the ceiling
Push the ceiling cover
up to the ceiling
SOLID RC CEILING
SOLID RC CEILING
SOLID RC CEILING
Recommended drill bit size:
diameter Ø12.7 mm / depth 60 mm ± 2
0
15. (x4)
18. 17 mm (x2)
26. M5x8 mm (x2)
27. (x1)
25. M5x10 mm (x2)
27. (x1)

10 11
STEP 2
1. Place the bearings onto the spindle.
2. Place the arm onto the spindle.
3. Manage the cables well and make sure that the C-clip is tted into the groove of the spindle securely, so the xed section of the
arm cannot be pulled out from the mount while adjusting the arm.
4. Put the rotating cover-L on the arm.
STEP 3
Adjust the height
1. Put the adjustable pole inside the ceiling mount.
2. Fix the pole at the desired height by wrench with 2 screws, 2 screw bushings, 2 washers and 2 nylon nuts.
Cable management
SOLID RC CEILING
Please use screws and
spacer sleeve to fix the
plastic cover to the pole.
Every pitch of adjustable
pole holes is 100 mm.
Cable management
16. (x2)
17. (x1)
18. 17 mm (x2)
22. (x4)
19. 3 mm (x1)
20. (x1)
21. (x2)
23. (x2)

12 13
NOTE
Please make sure this joint is in a vertical 90Oangle.
CABLE ASSEMBLY
PARTS
SOLID RC WALL
rotating cover-L
front cable cover
rotating cover top cable cover
middle cover-1R
end cover-2Rend cover-2Lmiddle cover-1L
VESA cable cover-S
grab handle
90O ± 1O
90O ± 1O

14 15
STEP 1.1
Remove the cable covers.
STEP 1.2
Run the cables through the arm. Assemble the cable wrapper.
1
3
2
4
2
1
Remove the VESA
cable cover with a
screw driver (not
provided), as shown.
Save the screws for
reattachment after the
monitor installation.
Slide the cable cover out
of the arm slot carefully,
as shown.
• The VESA adapter must be moved entirely down to
put the cable through.
• Allowing for arm movement, it is suggested to keep
at least 15 cm of cable left from the VESA adapter.
12. Cable wrapper (x1)
13. Cable tie (x4)
40O
15 cm

1716
1 2
4 5
3
MONITOR ASSEMBLY
STEP 1.1
Remove the back cover utilizing a screw driver (not included), as shown and pull out the cable in order to install the monitor.
NB. Please save the screws for reattachment of the cover after monitor installation.
STEP 1.2
Fix the monitor on the VESA mount, using the Allen key and screws.
Please note that the cable
should be placed under the
spring.
Please note that
the screw has to go
through the spring.
Support tools
4. M6x30 (x4)
8. 4 mm (x1)
5. M4x25 (x4)
6. (x4)
7. 2,5 mm (x1)
4 mm

18 19
STEP 1.3
Connect the cable to the monitor
Connect the cables to the monitor, complete the circuit and replace the VESA cable cover-B or VESA cable cover-S.
STEP 1.4
Fix the handle bar
1. Insert the handle bar into the 2 holes on the bottom of the VESA interface.
2. Fix the handle bar with 4 screws with a 2,5 mm Allen key through the 4 holes on the lower part of the VESA interface.
REPLACEMENT OF THE ARM COVERS
Follow the order as below to assemble the covers. Replace the adjuster covers as shown.
1
2
3
4
3. M4x12 (x4)
7. 2,5 mm (x1)

20 21
ADJUSTMENT FOR LOADING ADJUSTING UNIVERSAL JOINT TENSION
When assembling the arm with monitors of different weight, you may find that the tension of the universal joint needs to be
adjusted to ease movement or to maintain the desired monitor position. If so, adjust as follows:
1. Remove the plastic universal joint cover.
2. Find the nylon nut (not the screw head) and use the provided wrench to adjust the tension. Fix the screw head by wrench
during adjustment.
3. Use one hand to support the monitor and adjust the tension of the universal joint:
Clockwise: more tension
Counterclockwise: less tension
4. When the desired tension is achieved, replace the plastic covers.
Caution
• Support the monitor during the adjustment procedure.
• Only adjust the nylon nut (not the screw head).
• Do not disassemble the universal joint.
1
2
Screw Head
Nylon Nut
Caution for weight capacity adjustment
1. Make sure you have checked the weight of the monitor you wish to mount.
2. Support the arm throughout/ during installation.
3. Pull down the arm and take out the upper cap (see below figure) during adjustment.
Adjustment:
Use the Allen key provided to adjust the weight capacity. Turn the Allen key in a clockwise direction for
more weight and in counterclockwise direction for less weight.
Loading:
FPMA-HAC100: 1~6 kg
FPMA-HAC100HC: 6~12 kg
• The products loading capacity is based on the monitors’ center of gravity less than 3 cm from
the end of the VESA interface.
• The loading capacity could be reduced if the monitor size is bigger than 26 inches or the depth
is more than 5,5 cm.
• All product specifications in catalogues are subject to change without notice.
Fasten the screw with the 4 mm Allen key and adjust the tightness of rotation according to your wishes.

22 23
SAFETY NOTES
• Once assembled do not disassemble.
• Make sure that mounting screws are suitable for the horizontal surface and adequate to hold the weight of the arm and the
monitor.
• Support the monitor and arm throughout assembly and mounting.
• Keep small parts out of reach from children.
Do not hang or swing on the arm.
Do not hold the arm as a support to get up.
Monitors to be mounted should not weigh more than the
maximum weight capacity of the mount, as stated in this
manual.
Do not hang unnecessary objects on the arm.
Make sure that the horizontal surface is substantial
to hold the weight of the arm and the monitor. SOLID RC CEILING
Only use with LCD/ TFT monitors compliant with
VESA 75x75 mm or 100x100 mm.
LCD / TFT
MONITOR