NewerTech Power2U User manual

Power2U®
The NewerTech Power2U AC/USB wall outlet
offers a clean, convenient, and centralized
location to charge or power mobile devices in
addition to powering traditional AC-powered
devices.
The Power2U is an easy DIY install on any
15A electrical circuit and provides a flush,
standard wall outlet appearance that blends
in seamlessly with residential environments.
By incorporating both traditional three-prong
AC wall sockets and USB ports, the Power2U
AC/USB wall outlet enhances living and
working spaces by eliminating the clutter
created by multiple cables and unsightly
bulky power adapters.
CAUTION: READ BEFORE INSTALLING!
• An installation video is available at:
www.newertech.com/p2u-install/
• Failure to follow these instructions
can cause death or permanent injury.
Do not work on live electrical circuits!
• This product is for indoor, permanently
installed use only.
• Install the device in accordance with all
national and local electrical codes.
• Do not place the device to be charged in
direct sunlight or near direct heat, as this
will affect the charging function.
• Disconnect the USB cable from the USB
socket when not in use.
• It is normal for the battery in the device
being charged and the USB charger
itself to generate some heat during the
charging process.
General Information
This product is a 2-in-1 electrical wall socket. It
can be used as a standard 15A 120V electrical
receptacle, as well as for charging products
that utilize a USB connection up to 2.5 amps.
It is ideal for charging electronics such as
iPhone, iPad, iPod, MP3 players, PDAs, GPS
receivers, gaming consoles, and other devices
that charge via USB.
The NewerTech Power2U uses the most
advanced IC control system in the world,
and provides multiple levels of protection to
your device. The Power2U is manufactured
from high quality polycarbonate resin and all
internal components are UL-approved.
The Power2U has three (3) pre-stripped wire
leads for line, neutral, and ground for quick
and easy installation. The Power2U also
includes three (3) wire nuts to fasten the
leads.
Identify Cables and Wires
Do NOT install the NewerTech Power2U into
an electrical box that is smaller than 14 cubic
inches. If your electrical box contains more
than 4 wires (not including ground wires),
verify that its capacity is large enough to ac-
commodate this device before proceeding.
Do not overll the electrical box!
Wiring and Wire Connections
The Newer Technology Power2U is designed
to work with either solid wire or stranded
wire, 12 or 14 AWG. When attaching the wire
to the Power2U, please refer to the drawings
on Page 2 to ensure proper connection.
FOR SUPPORT PLEASE VISIT:
www.newertech.com/support/
Technical Specications
USB Input: AC 125V 50/60Hz 350mA
Operating Temperature: -10ºC to 35ºC
Relative Humidity: <=75%
USB Output: DC 5.2V 2.5A
AC Input: 15A, 125V (NEMA 5-15R)

• Connect the device’s black wire to the HOT (black) wire in the wall box.
• Connect the device’s white wire to the NEUTRAL (white) wire in the wall box.
• Connect the device’s green wire to the GROUND (green or bare) wire in the
wall box (only if a grounding wire is available -- if not, attach the green wire
to the wall box using a grounding screw).
➂Fold the wires into the electrical box. Screw the Power2U into the
electrical box. Screw the faceplate into the Power2U.
➃Turn the power back ON at the circuit breaker or fuse panel. Test the
Power2U receptacle (125V) power outlets and the 5.2V USB outlets to verify
proper operation. The USB outlets are only powered when a USB cord is
plugged into the port. There is an internal switch that is depressed when the
USB connector is inserted and then turns the USB power on.
Installation & Use
The installation of the Newer Technology Power2U is straightforward and
the same as replacing a normal electrical receptacle. The Power2U is a large
device; make certain that your electrical box can legally accommodate it!
Power2U Installation Steps:
➀ Turn the power OFF. This is done at the electrical circuit breaker box
or the fuse box. Find the circuit or fuse that corresponds to the receptacle
where you will install the Power2U, then turn the circuit breaker OFF or
remove the fuse before proceeding!
➁Connect the wires to the Power2U.
• Strip the wires inside of your wall box
1/2” (13mm) to accept the Power2U
device wires.
Wire
13mm
Strip wire 13mm (1/2”)
Patented by Winon Electrical Co. Ltd. # US 7,997,925
UL File # E339607
© 2015 Newer Technology, Inc.
R5 DM 5/1/2015
INSTALLATION VIDEO
www.newertech.com/p2u-install/