NewLine Slider User manual

Slider
INSTRUCTION MANUAL
1. When you receive your Newline shower check contents for any freight damage.
2. Advise Newline on 0508 639 5463 if any damage has occurred or a defect
identied within 8 hours of receiving the goods so this can be rectied.
3. Do not proceed with installation until resolved.
Important!
November 2019

2
WARRANTY
Faulty goods are covered under warranty. Visit www.newline.co.nz for warranty information.
Breakages incurred during construction are not covered under warranty.
Installations must conform to the instructions to be covered by the warranty.
HEALTH AND SAFETY
Toughened Glass:
• Do not rework precut glass panels. Cutting or altering a glass panel will cause it to explode without warning.
• Unpack all glass assemblies. Stand glass on soft packaging on the oor and against a wall. Care must be taken
not to strike any edge or corner against a hard surface as this will chip and destroy the glass panel.
Installation:
• Glass panels and assemblies are heavy. Two man lifting is recommended for handling and installation.
• Determine positioning of wiring and piping within wall cavities before shower installation. Mark their positions to
ensure electrical and piping areas are avoided.
• Wear appropriate protective clothing and eye protection during installation.
MATERIALS REQUIRED
Sika Silaex NG translucent Silicone
TOOLS REQUIRED
AFTERCARE
Newline recommend squeegeeing down the glass after every shower and cleaned weekly with a microber cloth,
mild detergent and water. Rinse with clean water and squeegee and wipe dry.
NEWLINE RECOMMENDS A SKILLED TRADESMAN ACQUAINTED WITH
SHOWER INSTALLATIONS TO ENSURE THE VERY BEST OUTCOME.
DOOR SET / IMPORTANT INFORMATION

3
PREPARATION CHECKLIST
ENSURE YOU TICK THE SPECIFIC BOXES THAT APPLY AS YOU PROGRESS
2 Sided Shower: Ensure the oor is level and the walls are plumb and at.
Position all framing for solid xing for the shower tray, shower and plumbing ttings. Wall proles require a
stud ush with the tray outside edge.
Ensure all plumbing items have been installed prior to the lining being attached.
Alcove Shower: Critical that the walls are constructed plumb and at. Request the specic width of the Acrylic
Tray prior to framing.
ACRYLIC TRAY AND LINER OPTION
• Detailed installation instructions are packed with the shower tray for tray and lining installation.
• Alcove application will require specic detailing of framing and is based on 10mm plasterboard lining.
• Shower waste and supply ttings must be installed by a registered plumber.
Page 4 to 8 2-Sided Shower
Page 9 to 14 3-Sided Alcove Shower
DOOR SET / IMPORTANT INFORMATION
INDEX

4
COMPONENT LIST: 2-SIDED
COMPONENT LIST: 2-SIDED DOOR AND RETURN PANEL

5
Walls out of plumb will not allow for full minimum/maximum options.
1
Apply silicone
bead down back
of channel prior to
fastening.
Refer to LAYOUT
options below
Min/Max Table above
LAY-OUT OPTIONS
Option 1: Standard Acrylic
Shower Tray size 1200 x 900 x
75mm high
Position the channel at 13mm off
tray edge on both sides. This allows
for walls out of line up to 4mm.
Reduce the measurement off tray
edge if oor and walls dictate this.
Option 2: Low Prole Acrylic
Shower Tray size 1200 x 915 x
40mm high
Mark channels at 18mm off tray
edge on both sides. Assess any
change at the door side that will
reduce the return panel extension,
as adjustment is 14mm against
4mm on door.
SHOWER TYPE WALL CHANNEL ADJUSTMENT
900mm Return Panel 870mm (minimum) to 888mm (maximum)
1200mm Door 1165mm (minimum) to 1185mm (maximum)
Mark wall prole. Fasten wall prole.

6
2
3
Fit return panel.
For details on door set assembly:
1. Door frame: Step 3 this page.
2. Glass door: Page 7 Step 4 & 5
Top & Bottom
Rails (03). Fit with
bump stops at
xed glass end.
Door Assembly

7
4
Door parts and seals
5
Adjust shower inwall proles and
square up door. Drill and fasten
door frame to wall prole.
Connect door set to
return panel. Drill and
fasten at corner.
Plumb corner
post and pack if
required.

8
6
7
Apply silicone to
join as indicated.
Seal the join
between wall prole
and frame, 150mm
up from base on
both sides.
Finally adjust door
alignment.

9
COMPONENT LIST: 3-SIDED ALCOVE
COMPONENT LIST: DOOR SET 3-SIDED ALCOVE
8
8
8
6
16

10
SHOWER TYPE WALL CHANNEL ADJUSTMENT
1200mm 1155mm (minimum) to 1185mm (maximum)
Walls out of plumb will not allow for full minimum / maximum options.
1
Position wall proles
onto door frame.
2
Top & Bottom
Rails (03). Fit with
bump stops at
xed glass end.
Door Assembly

11
3
Layout
Mark wall prole holes both sides.
Predrill liner with 2mm bit.
NOTE: Use Pivot Shower (p.10)
has details required.
Fasten wall proles.
Silicone bead on back
of wall channels prior
to installation.

12
5
Door Installation
Door Parts
Press button
4

13
6
7
Seal Install
Fitting of seals
Adjust rollers but do not
over tighten.
Align door frame
within wall channels
and square up door.
Fasten frame
to wall prole.
Adjust rollers
to alignment.

14
Apply silicone to outer join as indicated.
Seal the join
between wall prole
and frame, 150mm
up from base on
both sides.
8
CONTACT
Freephone: 0508 639 5463 Phone: [phone] Fax: [phone]
Email: [email protected] www.newline.co.nz