Newstripe Pack-Master Air User manual

P
ACKM ASTER
As s e m b l y In s t ru c t i o n s M o d e l # 1 0 0 0 1 2 5 8
NOTE: All parts that are to be mounted on the left side of the base plate are stamped with the letter “L”.
1. Mount left (1) and right (2) uprights to base plate (3) using 4, 1/2” x 1-1/2” long bolts, 8 flat washers and
4 Nylock nuts. NOTE: Do not tighten bolts all the way, so the jack assembly can be installed.
2. Place control levers (8) in the “UP” position and remove Face Plate from Jack assembly.
3. Insert tongue of ram (12) into left (uncapped) upright with Ram Bracket on UNDERNEATH side of uprights.
(See Assembly Instruction Detail) and assemble with 2, 1/2” x 4 -1/2” long bolts, 4 flat washers and
2 Nylock nuts.
4. Align uprights and ram assembly and tighten all bolts. Mount Face Plate back onto Jack Assembly.
5. Mount circular ram plate (7) to ram (5) using cotter pin supplied.
OPERATION OF PACKMASTER
1. To operate the PackMaster, swing the lower lever to the "DOWN" position first and then, swing the upper lever
to the "DOWN" position. With both control levers in the “down” position, begin pumping the Jack handle up
and down.
CAUTION: Always hold onto the jack handle while compacting. Jack handle may "SPRING" up when un-
der load and levers have not snapped all the way in.
2. To retract the compactor plate, while applying down-
ward pressure on jack handle, swing upper lever to "UP"
position first, then the lower lever. This removes pressure
on the pin and will extend the life of the jacking pins.
CAUTION:
Do not extend or modify the handle in any way.
Do not permanently bolt the PackMaster to the floor.
Damage and breakage of ram assembly and personal
injury may occur.
CAUTION:
Unit is not designed for crushing of glass containers or
items that may shatter or contain volatile vapors.
MAINTENANCE:
1. Jack Bar, Jack Pins and Jack Pivot Points must be
periodically lubricated with white lithium grease for
proper operation and warranty compliance.
Lubricate weekly if used daily. Lubricate monthly for
lighter use.
Fig. 1
Newstripe, Inc. 1700 Jasper St Unit F Aurora CO 80011 303-364-7786

Pack-Master
Assembly Detail
Figure 2
View from
rear of unit
Figure 3
View from
rear of unit
5. Jack Assembly
Face Plate
Tongue
Left Upright
4. Mounting Bracket
9. Jack Handle
5. Jack Assembly
with Face Plate
removed
8A
8
2. Right
Upright
1. Left
Upright
Front
Rear
3. Base Plate
7. Ram Plate
Assembly

Replacement Parts List
PackMaster 10001258
Item Description Part Number
1Left Upright 10001425
2 Right Upright 10001426
3 Base Plate 10001289
4 Mounting Bracket 10001427
5 Jack Assembly 10001458
6 Face Plate N/A
7 Ram Plate Assembly (20” Dia.) 10001428
(17” Dia) 10001288
8 4” Jack Pin w/lever (Lower) 10001568
3” Jack Pin w/lever (Upper) 10001567
9 Jack Handle N/A
10 Spring, Bottom Pin 10001305
11 Spring, Top Pin 10001306
12 Jack Tongue N/A
CAUTION EXTREMELY DANGEROUS
Do not extend or modify the handle in any way. Do not permanently bolt PackMaster to
floor. Damage and breakage of ram assembly and personal injury may occur.
Newstripe, Inc. 1700 Jasper St Unit F Aurora CO 80011 303-364-7786

-Im p o rt a n t -
As s e m b l y In s t ru c t i o n D e t a i l s
OPERATION NOTE: To move “Up” and “Down” levers to
“Up” position after compacting, place down pressure on jack handle
while moving levers to the “Up” position.
Newstripe, Inc.
1700 Jasper St, #F Aurora , Co 80011 303-364-7786 Fax [phone]
Ram bracket must
be mounted on
bottom of uprights
View from
back of jack
assembly
Jack Tongue is inserted
INSIDE opening in left
upright
Front view showing components in
correct position for final assembly

THE NEWSTRIPE WARRANTY
Newstripe, Inc., warrants to the original purchase, for 18 (eighteen) months after date of purchase, that the equipment
hereby sold shall be free from defects in materials and workmanship. This warranty does not extend to any damage or
malfunction resulting from misuse, neglect, accident or improper operation.
Damage incurred in shipment from Newstripe, Inc. to the customer is the total responsibility of the carrier. Customer
must note damages on the Bill of Lading of Trucking Company or Railroad; and Newstripe, Inc. will furnish to you
the cost or parts and labor. You can then bill the common carrier for the damages by placing his signature on the
documents.
The Newstripe, Inc. obligation under this warranty and any implied warranties is limited to replacement or repair of
defective parts of its manufacturer without charge for 18 (eighteen) months from date of purchase. For service under
this warranty, buyer shall ship the defective part, parts of equipment, transportation
prepaid, to Newstripe, Inc. together with a written description of any claimed defect and proof of purchase date of the
materials being returned.
The gasoline engine and compressors are furnished with their respective manufacturer's warranties only. Such com-
ponents are not covered by any warranty of Newstripe, Inc.
The responsibilities described above are the only responsibilities of Newstripe, Inc. under this written
warranty or any implied warranty and may be exercised only within 18 (eighteen) months from the date
of purchase. In no event shall Newstripe, Inc. be liable for incidental or consequential damages and no person had an
y
authority to bind it to any representation or warranty, not be responsible for work done, materials furnished or repairs
made by others without its specific written authorization.
THIS WARRANTY SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, AND THERE IS NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND WITH
RESPECT TO THE GOODS SOLD HEREBY EXCEPT AS SET FORTH HEREIN. IT IS EXPRESSLY AGREED
THAT THIS WARRANTY SHALL BE LIMITED TO THE ADJUSTMENT, REPAIR OR REPLACEMENT OF
PARTS AND THE LABOR AND SERVICES REQUIRED THEREBY. IN NO EVENT, INCLUDING ANY
CLAIM FOR NEGLIGENCE, SHALL NEWSTRIPE, INC. BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
NEWSTRIPE, INC 1700 Jasper St #F Aurora, CO 80011 [phone]