NEXCAM AXIS SC-360 User manual

AXIS SHOOTING CHAIR
INSTRUCTION MANUAL
MODEL: AXIS SC-360
THIS INSTRUCTION MANUAL MUST ALWAYS ACCOMPANY THIS PRODUCT AND BE TRANSFERRED WITH IT UPON
CHANGE OF OWNERSHIP, WHEN LOANED, OR PRESENTED TO ANOTHER PERSON.
Thank you for purchasing our NEXCAM Chair. This product is designed by hunters, for hunters. It is engineered for
safety, comfort, steady shot, and stealth, putting the odds in your favor when the moment of truth arrives.
Constructed with only the highest quality materials it’s built for years of satisfying hunts.
Read this instruction manual and all warnings in its entirety before using this product.
If you have any questions on assembly, use, safety warnings, or anything else, please contact us by email at
[email protected]m.
YOU MUST READ, UNDERSTAND, FOLLOW ALL WARNINGS AND INSTRUCTIONS
BEFORE USING THIS PRODUCT!
DO NOT EXCEED Maximum Weight Limit - 300lbs. Exceeding this limit will damage
chair and may cause personal injury.
GROUND USE ONLY! NEVER USE AT HEIGHTS ABOVE GROUND LEVEL!
USE ONLY ON LEVEL SURFACE.
ALWAYS BE SURE HEIGHT ADJUSTMENT D-PIN IS INSERTED AND LOCKED THROUGH
BUSHING AND MALE POST AND BASE IS FLAT ON SURFACE BEFORE USING CHAIR.
DO NOT tip or lean back to tip chair while seated.
DO NOT use for any purpose other than intended use.
To avoid injuries to fingers and pinch hazards, use care when folding / adjusting
shooting rail and adjusting spring stopper knob.
Do not modify, jump, bounce or stand on this product.
Questions contact NEXCAM by email at [e-mail].
Always follow safe weapon/firearm handling practices.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR
DEATH!
1
QUESTIONS? Email [e-mail] for assistance.

Chair Diagram
2
QUESTIONS? Email [e-mail] for assistance.
Pinch Point Hazard.
Keep hands clear of
Shooting Rail Rest
(Both Sides)
Pinch Point Hazard.
Keep hands clear of
spring stopper knob

Parts List
1
Seat Fabric
Frame
Qty
1
2
Backrest
Support Frame
Qty
1
3
Seat Support
Frame
Qty
1
4
Accessory
Hooks
Qty
2
5
Armrest
Qty
2
6
Male Post
Qty
1
7
Seat Base
Qty
1
8
Rear Shooting
Rail Brace
Qty
2
3
QUESTIONS? Email [e-mail] for assistance.

Parts List
9
Bent Shoot Rail
Brace
Qty
2
10
Front Shooting
Rail Brace
Qty
1
11
Shooting Rail
Stoppers
Qty
2
12
Cup Holder
Qty
1
4
QUESTIONS? Email [e-mail] for assistance.

Hardware
Step
1
M6X30 (with steel
washer)
Qty
6
Step
2
M6X40 (with steel
washer)
Qty
2
Step
3
M6X80 (with steel
washer)
Qty
4
Step
4
M8X40 (with steel
washer)
Qty
4
Step
5
M6X45 (with steel
washer)
White Bushing
Spacer (located in
separate package)
Qty
1
1
Step
6
M6X75 (with
steel washer)
Qty
2
Step
9
M8 Stopper With
Locknut
Qty
2
QUESTIONS? Email [e-mail] for assistance. 5

Setup Instructions
Step 1:
Locate the Seat Fabric Frame
(#1), Backrest Support (#2)
and Seat Support (#3). Install
Seat Support (#3) and
Backrest Support (#2) onto
Seat Fabric Frame (#1) using
six (6) M6x30 Bolts, Steel
Washers and Locknuts as
shown in Figure1. Securely
tighten bolts.
IMPORTANT NOTE: Taller
side of Seat Support is
Positioned to Front of Seat.
Hint: Install one bolt on
side of backrest support
and slide other side into
place and assemble
remaining bolts. Do same
for seat support.
Step 2:
Locate two (2) Accessory
Hooks (#4). Install Accessory
Hooks(#4) on outside of Seat
Fabric Frame (hooks facing
up) using two (2) M6x40 Bolts,
Steel Washers and Locknuts
as shown in Figure 2.
Securely tighten bolts.
Figure 1
Install Seat & Backrest Seat Supports
Figure 2
Install Accessory Hooks
6
QUESTIONS? Email [e-mail] for assistance.
Taller Side of
Seat Support is
Positioned to
Front of Seat

Setup Instructions
Step 3:
Locate two (2) Armrest (#5).
Install Armrest (#5) onto sides
of Seat Fabric Frame (#1)
using four (4) M6x80 Bolts,
Steel Washers black nylon
washers (placed between
armrest and seat fabric frame)
and Locknuts as shown in
Figure 3. Securely tighten
bolts.
Figure 3
Install Armrests
7
QUESTIONS? Email [e-mail] for assistance.
Step 4:
With Webbing Stoppers on
top of Rocker Springs,
position assembled Seat
Frame on top of assembled
Rocker Springs so curve of U
on Rocker Springs face back
of chair. Assemble together
using four (4) M8x40 Bolts,
Steel Washers and Locknuts
as shown in Figure 4.
Note: Front two (2) M8x40
bolts go through Chair Frame,
Webbing Stoppers and
Rocker Springs.
Securely tighten bolts.
Curve Faces
Back of Seat
Webbing
Stoppers
assembled
between Chair
Frame and
Rocker Springs
Figure 4
Install Rocker Springs

Setup Instructions
Step 5:
Place White Bushing Spacer
onto male post and place male
post of assembled Seat into
female hole of Seat Base (#7)
as shown in Figure 6. Place
one (1) M6x45mm Bolt and
Locknut through male post as
shown in Figure 5. Securely
tighten all bolts.
Bolt prevents seat base from
coming off from seat.
8
QUESTIONS? Email [e-mail] for assistance.
Place White Bushing
Spacer onto Male Post
Figure 5 Assemble
Seat Onto Seat Base
IMPORTANT NOTE:
To adjust seat height –
Position Seat Height
Collar on Male Post
and Place D-Pin
through Collar and
Seat Height Hole to
secure seat Position.

Setup Instructions
Step 7:
Assemble two (2) Bent Up
Shooting Rail Braces (#9) on
Front Shooting Rail Brace (#10)
using two (2) Locking Knobs
as shown in Figure 7.
Securely tighten.
Figure 7
Assemble Shooting Rail Front and Bent Up Braces
9
QUESTIONS? Email [e-mail] for assistance.
Step 6:
Assemble Rear Shooting Rail
Brace (#8) to Seat Fabric
Frame (#1) using M6x75 Bolt,
Steel Washers, Bushing
(between seat frame and
brace), nylon washers and
Locknut as shown in Figure 6.
Securely tighten all bolts.
Repeat this on other side for
other Rear Shooting Rail Brace.
Nylon Bushing
Nylon Washer
Nylon Washer
Steel Washer
Steel Washer
Locknut
Figure 6
Assemble Rear
Shooting Rail
Brace to Seat
Frame
M6x75 Bolt

Setup Instructions
Step 9:
Assemble two (2) Shooting
Rail Stoppers (#11) to sides of
backrest frame using two (2)
M8 Locknuts as shown in
Figure 9. Securely tighten. Figure 9
Assemble Shooting Rail Stoppers
Figure 10
Assemble Shooting Rail to Seat Frame
Step 10:
Install Cup Holder (#12) onto
front side of seat using steel
washers and locknuts as
shown in Figure 10.
10
QUESTIONS? Email [e-mail] for assistance.
Step 8:
Insert Bent Up Shooting Rail
Braces (#9) into Rear Shooting
Rail Brace (#8) as shown in
Figure 8. Using two (2) Locking
Knobs securely tighten
shooting rail.
WARNING! Always make
sure bent up shooting rail
brace is inserted past
locking knobs and secured
in place prior to using
shooting rail.

USE:
USE ONLY ON LEVEL SURFACE. If chair is not stable or tips, do not use and
select another level surface.
ALWAYS BE SURE HEIGHT ADJUSTMENT D-PIN IS INSERTED AND LOCKED
THROUGH BUSHING AND MALE POST
DO NOT tip or lean back chair while seated.
To avoid injuries to fingers and pinch hazards, use care when folding and
adjusting shooting rail.
To avoid injuries to fingers and pinch hazards, only adjust spring stopper
knob when no one is seated in chair.
Prior to every use, inspect chair for damage. DO NOT USE IF ANY
DAMAGE IS VISIBLE OR SUSPECTED, including but not limited to cuts,
frayed portions, corrosion, or other damage to chair. If damage is visible
or suspected, DO NOT USE THE PRODUCT. If there are any questions, DO
NOT use the product and contact NEXCAM by email at
[e-mail]. for assistance.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS
INJURY OR DEATH!
Place Chair on a level surface with base flat on surface. Adjust seat height as shown in setup instructions so
seat height is at comfortable height.
While next to chair, adjust Spring Stopper Knob as shown in setup instructions to adjust amount of Forward
Spring Travel.
Adjusting Shooting Rail for Shooting Use:
- Adjust vertical, horizontal and angular adjustments for comfortable shooting rest position as shown in
setup instructions.
Adjusting Shooting Rail for Archery Use:
- Loosen shooting rail horizontal adjustment knobs and remove shooting rail. Using angular adjustment
pins, pin shooting rail arms down to armrest to lock them in place.
Chair is ready to be used.
MAINTENANCE AND STORAGE:
Do not modify this product in any way by making repairs, replacing parts, altering,
adding or attaching anything to it except if explicitly authorized in writing by
NEXCAM.
Use only NEXCAM authorized replacement parts. The use of unauthorized
replacement parts may result in serious injury or death.
Proper maintenance and inspection is required for this product.
This product is used to support your weight. Never use a chair that is damaged in
any way. Do not use if it is not wholly free of damage. If you have questions,
contact NEXCAM by email at supp[email protected]m for assistance.
Failure to follow these instructions can lead to serious injury or death.
Should any damage occur or to purchase NEXCAM replacement parts, contact customer service by email at
[email protected]m for assistance.
Care and maintenance is required to assure trouble free performance of your chair.
Store this product indoors in a clean, dry environment free from direct sunlight, harmful chemicals,
excessive heat and dust. Exposure to sunlight, excessive heat and the elements can weaken material over
time.
11
QUESTIONS? Email [e-mail] for assistance.

LIMITED WARRANTY*.
LIMITED ONE YEAR WARRANTY. WE WARRANT THIS PRODUCT AGAINST ANY MANUFACTURER DEFECTS
IN MATERAILS AND WORKMANSHIP FOR PERIOD OF ONE YEAR FROM DATE OF PURCHASE FROM
AUTHORIZED RETAILER TO THE ORIGINAL OWNER. WE WILL REPAIR OR REPLACE ANY PART FOUND
DEFECTIVE IF THE UNIT CLAIMED TO BE DEFECTIVE IS RETURNED TO US POSTAGE PREPAID, WITHIN
WARANTY PERIOD. CONTACT CUSTOMER SERVICE AT [e-mail] FOR WARRANTY
CLAIMS.
This warranty is void if any product has been subjected to misuse, abuse, neglect (including but not
limited to improper maintenance or failure to follow instructions), storage, improper use, misapplication,
accident, normal wear, modification, adjustment, or repair.
NO OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THE PRODUCT.
LIMITATION OF LIABILITY
It is expressly understood that our liability for this product, whether due to breach of warranty,
negligence, strict liability, or otherwise , is limited to repair of the product as stated above. We will not
be liable for any other injury, loss, damage, or expense, whether direct or consequential, including but
not limited to loss of use, income, profit, or damage to material from use of this product howsoever
caused.
SERVICING YOUR PRODUCT:
If you need repairs or have warranty issues, contact Customer Service at [email protected]
for assistance.
PLEASE NOTE:
We reserve the right to make substitutions on warranty coverage for any reason, including but not
limited to available parts.
*Limited Warranty to the Original Owner.
NEXCAM INC.
405 Annandale Blvd.,
Annandale, MN 55302
Email: [e-mail]
Website: https://nexcam.com
12
QUESTIONS? Email [e-mail] for assistance.