Whittier Wood 5025KFDH User manual

For normal household use only.
recommended for commercial use.
Production Code:
Completely read the Assembly Instructions
before beginning your project.
Store the parts: 1) in their box; 2) in a dry place;
3) in temperatures ranging from 40° to 90°.
(Not on a cold, possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
affect the stability of your furniture. Tighten or
repair as needed.
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading the Assembly Instructions before you begin
your project.
Service Policy: We will replace any
parts which are defective, missing or
damaged during assembly. Please contact
Whittier Wood Products customer service
department directly (by phone, fax, mail or
email) for replacement parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number (upper left corner of this
page), part letter/number, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213Outside U.S. or Canada: 541-687-0213
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Do not climb, sit or stand on this piece of
furniture.
Model #
Portland II Trestle
Table
Assembly Instructions
5025KFDH
P.O. Box 2827
Eugene, OR 97402 USA
Fax: [phone] • www.whittierwood.comFax: 541-687-2060 • www.whittierwood.com
VN 01/09/09

5025KFDH Portland II Trestle Table — Parts List
Page 2 – 5025KFDH - 01/09/09
I — Wood Button — Qty.
L — T-Nut
— Qty. 4 (inserted)
M — Adjustable Glide
— Qty. 4 (inserted)
4
H — 8mm x 30mm Wood Dowel
— Qty. 8 (6 inserted)
J – Hex Wrench – Qty. 1
G — #8x1¼" Pan Head Screw
— Qty. 14
E — ¼" x 66mm Hex Bolt
— Qty. 4
F — Barrel Nut — Qty. 4
A — Leg — Qty. 2
C — Middle Support — Qty. 1 D — Top — Qty. 1
B — Top Support — Qty. 2
Before you assemble this product, identify its parts and make sure quantities received match what is on this list.
If you need to replace a part, please refer to the following list for its name and letter.

E
E
C
F
x 4
x 2
Page 3 – 5025KFDH - 01/09/09
B
G
A
A
F
F
5025KFDH Portland II Trestle Table
ASSEMBLY INSTRUCTIONS
x 4
G
x 4
E
Fig. 1
Fig. 2
TOOLS REQUIRED: Hex Wrench (provided), Phillips Screwdriver,
Mallet or Padded Hammer, Wood Glue, Slotted Screwdriver
1. Spread a thin film of glue into the dowel holes of the Top Support (B) and place over dowels
of the Leg (A). Gently tap with a padded hammer and quickly wipe away any excess glue.
Secure with #8x1¼" Pan Head Screw (G). See Figure 1.
2. Spread a thin film of glue in the dowel holes on the Legs (A). Insert Middle Support (C) and
quickly wipe away any excess glue. See Figure 2.
Secure with ¼"x66mm Hex Bolts (E) and Barrel Nuts (F). NOTE: The bottom of the Barrel Nut
is grooved. When you insert the nut into the Middle Support, make sure the grooved end points
out (either up or down) so you can use a slotted screwdriver to properly align the nut.
See Figures 2a and 2b.
Fig. 2a
Fig. 2b

I
I
D
G
H
Page 4 – 5025KFDH – 01/09/09
x 10
G
x 4I
C
AA
Hx 2
H
Fig. 3
Fig. 4
NOTE: You do not need to
glue the dowels in this step.
They are for alignment
purposes only.
3. Place Top (D) face-down on a clean, protected surface. Insert two Dowels (H) into the dowel holes
as shown in Figure 3. Position the leg assembly so that the corresponding dowel holes in the top
supports fit over the dowels in the seat. Using the predrilled holes in the Top Support as guides,
secure with #8x1¼" Pan Head Screws (G). See Figure 3.
NOTE: The inside middle holes of the top supports do not receive screws.
no screws
4. Glue Wood Buttons (I) into the exposed holes. Wipe away any excess glue. See Figure 4. Adjust
the Glides (M) in the bottoms of the legs to level your table.