Nexcom NSA 5130 User manual

NEXCOM International Co., Ltd.
NEXCOM International Co., Ltd.
Published April 2014 www.nexcom.com
Network and Communication Solutions
Network Security Appliance
NSA 5130
User Manual

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. ii NSA 5130 User Manual
Contents
Contents
Preface
Copyright ............................................................................................. iv
Disclaimer ............................................................................................. iv
Acknowledgements .............................................................................. iv
Regulatory Compliance Statements ....................................................... iv
Declaration of Conformity...................................................................... iv
RoHS Compliance ................................................................................... v
Warranty and RMA ................................................................................ vi
Safety Information ................................................................................vii
Installation Recommendations................................................................vii
Safety Precautions.................................................................................viii
Technical Support and Assistance........................................................... ix
Conventions Used in this Manual........................................................... ix
Global Service Contact Information......................................................... x
Package Contents..................................................................................xii
Ordering Information ............................................................................xiii
Chapter 1: Product Introduction
Overview ................................................................................................1
Key Features.........................................................................................1
Hardware Specifications..........................................................................2
NSA 5130 System.................................................................................2
Main Board (NSB 5130) ........................................................................4
Getting to Know NSA 5130 ....................................................................7
Front Panel ...........................................................................................7
Rear Panel ............................................................................................8
Chapter 2: Jumpers And Connectors
Before You Begin ....................................................................................9
Precautions .............................................................................................9
Jumper Settings ....................................................................................10
Locations of the Jumpers and Connectors.............................................11
NSB 5130 ...........................................................................................11
Jumpers................................................................................................12
Connectors Pin Definitions....................................................................14
External I/O Interface ........................................................................14
Status Indicators.............................................................................14
USB Ports.......................................................................................14
RJ45 Type Console Port ..................................................................15
Software Push Button ....................................................................15
LAN1 Port ......................................................................................16
LAN2 Port ......................................................................................16
LAN3 Port ......................................................................................17
LAN4 Port ......................................................................................17
LAN5 Port ......................................................................................18
LAN6 Port ......................................................................................18
LAN7 Port ......................................................................................19
LAN8 Port ......................................................................................19
VGA Connector .............................................................................20

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. iii NSA 5130 User Manual
Contents
Internal Connectors..........................................................................21
SATA2 Port.....................................................................................21
SATA3 Port.....................................................................................21
SATA4 Port.....................................................................................22
SATA Power Connector ..................................................................22
SATA DOM Power Connector.........................................................23
Digital I/O Connector (4 Input, 4 Output) .......................................23
COM2 Connector ..........................................................................24
USB Connector ..............................................................................24
Parallel Interface for LCM Module ..................................................25
LCM Keypad Connector.................................................................25
HW Reset Button ...........................................................................26
Power Button.................................................................................26
Power Connector...........................................................................27
GAL Programming Connector ........................................................27
System Fan (FAN1) .........................................................................28
System Fan (FAN2) .........................................................................28
CPU Fan Connector........................................................................29
System Fan Connector ...................................................................29
PCIe Slot ........................................................................................30
PCIe Gold Finger (for LAN Module).................................................32
Block Diagram of the Main Board .........................................................34
Chapter 3: System Setup
Removing the Chassis Cover ................................................................35
Installing a DIMM..................................................................................36
Installing the CPU .................................................................................38
Installing a CompactFlash Card .............................................................44
Installing a 3.5” SATA Hard Drive ..........................................................46
Installing a PCI Express x8 Card .............................................................49
Replacing the LAN Module....................................................................51
Rackmount Bracket Kit (optional)..........................................................55
Chapter 4: BIOS Setup
BIOS Setup Utility..................................................................................61
Main ..................................................................................................61
Advanced ...........................................................................................62
Chipset...............................................................................................77
Boot ...................................................................................................82
Security ..............................................................................................83
Save & Exit .........................................................................................84
Appendix A: Watchdog Timer
Watchdog Timer Setting .......................................................................85
CRFC6 (Default 0x00) ...........................................................................85
Appendix B: GPI/O Programming Guide
GPIO (J9)...............................................................................................87
Appendix C: Bypass Specifications
Bypass Control Register Map.................................................................90
Bypass Control Register Bit Definitions ..................................................91
Appendix D: Power Consumption
Power Consumption .............................................................................93

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. iv NSA 5130 User Manual
Preface
Preface
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices
and describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area (domestic environment) is likely to cause harmful interfer-
ence, in which case the user will be required to correct the interference
(take adequate measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable Euro-
pean Union (CE) directives if it has a CE marking. For computer systems to
remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by con-
stantly checking its manual posted on our website: http://www.nexcom.
com. NEXCOM shall not be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use of any product, nor for any
infringements upon the rights of third parties, which may result from such
use. Any implied warranties of merchantability or fitness for any particular
purpose is also disclaimed.
Acknowledgements
NSA 5130 is a trademark of NEXCOM International Co., Ltd. All other
product names mentioned herein are registered trademarks of their respec-
tive owners.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vNSA 5130 User Manual
Preface
RoHS Compliance
NEXCOM RoHS Environmental Policy and Status
Update
NEXCOM is a global citizen for building the digital infra-
structure. We are committed to providing green products
and services, which are compliant with European Union
RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment)
directive 2011/65/EU, to be your trusted green partner and to protect our
environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the suf-
fix “(LF)” will be added to the compliant product name.
All new product models launched after January 2006 will be RoHS compli-
ant. They will use the usual NEXCOM naming convention.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vi NSA 5130 User Manual
Preface
Warranty and RMA
NEXCOM Warranty Period
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning
on the date of invoice by NEXCOM. HCP series products (Blade Server)
which are manufactured by NEXCOM are covered by a three year warranty
period.
NEXCOM Return Merchandise Authorization (RMA)
?Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
?Customers must collect all the information about the problems encoun-
tered and note anything abnormal or, print out any on-screen messages,
and describe the problems on the “NEXCOM RMA Service Form” for
the RMA number apply process.
?Customers can send back the faulty products with or without acces-
sories (manuals, cable, etc.) and any components from the card, such as
CPU and RAM. If the components were suspected as part of the prob-
lems, please note clearly which components are included. Otherwise,
NEXCOM is not responsible for the devices/parts.
?Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
?Any products returned by NEXCOM to other locations besides the cus-
tomers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one
is basic diagnostic fee and another is component (product) fee.
System Level
?Component fee: NEXCOM will only charge for main components such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistor, capacitor.
?Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
?Replace with 3rd party products if needed.
?If RMA goods can not be repaired, NEXCOM will return it to the cus-
tomer without any charge.
Board Level
?Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistors, capacitors.
?If RMA goods can not be repaired, NEXCOM will return it to the cus-
tomer without any charge.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vii NSA 5130 User Manual
Preface
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are incon-
sistent with these instructions or the instructions for accessory modules,
contact the supplier to find out how you can ensure that your computer
meets safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the de-
scribed procedures only at an ESD workstation. If no such station is avail-
able, you can provide some ESD protection by wearing an antistatic wrist
strap and attaching it to a metal part of the computer chassis.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufactur-
er. Discard used batteries according to the manufacturer’s instructions.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A grounding strap
• An anti-static pad
Using your fingers can disconnect most of the connections. It is recom-
mended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. viii NSA 5130 User Manual
Preface
Safety Precautions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a stable surface during installation. Dropping
it or letting it fall may cause damage.
7. Do not leave this equipment in either an unconditioned environment
or in a above 40oC storage temperature as this may damage the
equipment.
8. The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source is correct before connect-
ing the equipment to the power outlet.
10. Place the power cord in a way so that people will not step on it. Do
not place anything on top of the power cord. Use a power cord that
has been approved for use with the product and that it matches the
voltage and current marked on the product’s electrical range label.
The voltage and current rating of the cord must be greater than the
voltage and current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
13. Never pour any liquid into an opening. This may cause fire or electri-
cal shock.
14. Never open the equipment. For safety reasons, the equipment should
be opened only by qualified service personnel.
15. If one of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
16. Do not place heavy objects on the equipment.
17. The unit uses a three-wire ground cable which is equipped with a
third pin to ground the unit and prevent electric shock. Do not defeat
the purpose of this pin. If your outlet does not support this kind of
plug, contact your electrician to replace your obsolete outlet.
18. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTER-
IES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
19. The computer is provided with CD drives that comply with the ap-
propriate safety standards including IEC 60825.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. ix NSA 5130 User Manual
Preface
Conventions Used in this Manual
Warning: Information about certain situations, which if not
observed, can cause personal injury. This will prevent injury to
yourself when performing a task.
Caution: Information to avoid damaging components or losing
data.
Note: Provides additional information to complete a task easily.
Technical Support and Assistance
1. For the most updated information of NEXCOM products, visit NEX-
COM’s website at www.nexcom.com.
2. For technical issues that require contacting our technical support team
or sales representative, please have the following information ready
before calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with
care.
2. Maintenance: to keep the unit clean, use only approved cleaning prod-
ucts or clean with a dry cloth.
3. CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xNSA 5130 User Manual
Preface
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
15F, No. 920, Chung-Cheng Rd.,
ZhongHe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.nexcom.com
America
USA
NEXCOM USA
2883 Bayview Drive,
Fremont CA 94538, USA
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com
Asia
Taiwan
Central Taiwan Office
16F, No.250, Sec. 2, Chongde Rd.,
Beitun Dist., Taichung City 406, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
Japan
NEXCOM Japan
9F, Tamachi Hara Bldg., 4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom-jp.com
China
NEXCOM China
1F & 2F, Block A, No. 16 Yonyou Software Park,
No. 68 Beiqing Road, Haidian District,
Beijing, 100094, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Shanghai Office
Room 603/604, Huiyinmingzun Plaza Bldg., 1,
No.609, Yunlin East Rd.,
Shanghai, 200062, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xi NSA 5130 User Manual
Preface
Europe
Italy
NEXCOM ITALIA S.r.l
Via Gaudenzio Ferrari 29,
21047 Saronno (VA), Italia
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcomitalia.it
United Kingdom
NEXCOM EUROPE
10 Vincent Avenue,
Crownhill Business Centre,
Milton Keynes, Buckinghamshire MK8 0AB,
United Kingdom
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.eu
Shenzhen Office
Room1707, North Block, Pines Bldg.,
No.7 Tairan Rd., Futian Area,
Shenzhen, 518040, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Wuhan Office
1-C1804/ 1805, Mingze Liwan,
No. 519 South Luoshi Rd.,
Hongshan District,
Wuhan, 430070, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Chengdu Office
9F, Shuxiangxie, Xuefu Garden,
No.12 Section 1, South Yihuan Rd.,
Chengdu, 610061, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xii NSA 5130 User Manual
Preface
Package Contents
Before continuing, verify that the NSA 5130 package that you received is complete. Your package should have all the items listed in the following table.
Item P/N Name Description Qty
1 19S00513000X0 NSA5130 ASSY 1
2 5044440031X00 RUBBER FOOT KANG YANG:RF20-5-4P 19.8x18x5.0mm 4
3 6012200052X00 PE ZIPPER BAG #8 170x240mm,W/China RoHS SYMBOL 1
4 6012200053X00 PE ZIPPER BAG #3 100x70mm,W/China RoHS SYMBOL 1
5 6023309081X00 CABLE EDI:232091081804-RS COM PORT. DB9 FEMALE TO RJ45 8P8C L:1800mm 1
6 6029900037X00 DOW CORNING 340 Silcone Heat Sink Compound (3g) 1
7 50311F0102X00 (H)ROUND HEAD SCREW LONG FEI:P6#32Tx 1/4/SW7*0.8 W/SPRING+FLAT WASHER P6#32Tx 1/4/SW7x0.8 NI 4
8 5043330272X00 TP10 CF BRACKET CHYUAN-JYH:L10Z361 46.4x49.2x8.8mm 301 STAINLESS STELL T:0.5mm 1
9 60233ATA12X00 SATA CABLE FOR NISE 1000 BEST:109-0707-150R 26AWG L:150mm 1
10 60177A0232X00 (N)NSA5130 QUICK REFERENCE GUIDE VER:A KRAMER 1
11 602DCD0355X00 (N)NSA5130 CD DRIVER VER:1.0 JCL 1
12 6014401238X00 NSA5130 W/O LCM MEMBRANE VER:A GREATWOOD 42x427.8x0.582mm 1

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xiii NSA 5130 User Manual
Preface
Ordering Information
The following provides ordering information for NSA 5130.
• Barebone
NSA 5130 (P/N: 10S00513000X0)
- Supports Intel®2nd generation Core™ processors, 4 DDR3 memory
slots, 8 PCIe GbE LAN ports, CompactFlash socket, USB ports, VGA
port, 1 PCIe x8 expansion slot, w/o LCM
• Options
P/N Controller Interface Type Ports Bypass/Segment Expansion Slot Location Slot
NSK5380-C8 10SK0538000X0 INTEL®NH82580EB PCIe x8 8 Copper Dual Latch/2 None All Slot
NSK5380-F8 10SK0538001X0 INTEL®NH82580EB PCIe x8 8 SFP None None All Slot
NSK5380-C4F4 10SK0538002X0 INTEL®NH82580EB PCIe x8 4 Copper / 4 SFP Dual Latch/2 None All Slot
NSK5380-F4 10SK0538003X0 INTEL®NH82580EB PCIe x8 4 SFP None None All Slot
NSK5399-F2 10SK0539900X0 INTEL®L82599ES PCIe x8 2 SFP None None All Slot

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 1NSA 5130 User Manual
Chapter 1: Product Introduction
Chapter 1: Product Introduction
Overview
Key Features
• 1U Rackmount Network Platform
• Intel®2nd Generation Core™ Processors
• 4x DDR3 1066/1333 Memory, up to 16GB
Rear
• 8+8 x GbE LAN Ports
• 1x internal 3.5” HDD Bay / 2x 2.5” HDD Bay (optional)
• 1x PCIe x8 expansion
Front

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 2NSA 5130 User Manual
Chapter 1: Product Introduction
Hardware Specifications
NSA 5130 System
Physical Characteristics
• Form Factor
- 19” 1U
• Construction
- SECC steel plate, 1.0 mm thick
• Color
- Nexcom 295U
• Dimensions (W x D x H)
- 430 mm x 450 mm x 44 mm
• Mounting
- Mounting ear
• System chassis
- NSC5130
System Cooling
• Cooling Method
- Removable system fan at the rear of the chassis
• Cooler Type
- Four system fans with controllable fan speed
• Ventilation
- Suction from the side and discharged to the back
Main Board
• NSB 5130
• Intel®2nd generation Core™ processors, Max 95watt
• Intel®C206
• 4 x 240-pin DDR3 1066/1333MHz DIMM sockets, up to 16GB ECC/
non-ECC SDRAM
• Intel®82583V LAN chip, LAN Bypass: 4 pairs, 10/100/1000 link speed
I/O Interface - Front
• Console port
- 1 RJ45 type
• USB port
- 2 USB ports
• LAN port
- 8 RJ45 copper LAN ports
• Keypad (optional)
- LCM keypad
• LCD
- 2x16 characters LCD module, PIO interface (optional)
• Button
- 1 GPIO software button
• LAN module bay (optional)
- 1 LAN module bay
• LEDs
- Power Status/HDD Status/LAN Status/Bypass Status LED
I/O Interface - Rear
• 1 VGA port (optional)
• 2 USB 2.0 ports (optional)
• 1 expansion slot
Storage
• 1 onboard CompactFlash socket
• 1 internal 3.5” HDD bay or 2 2.5” HDD bay
• 1 SATA DOM device space
Expansion
• 1 x PCIe x8 slot

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 3NSA 5130 User Manual
Chapter 1: Product Introduction
Standard Power Supply
• Power type
- Standard 200W ATX power supply
• Input voltage
- AC 100V - 240V
• Output voltage
- DC +5V, -5V, +12V, -12V, +3.3V, +5VSB
• Maximum output power
- Up to 250W for Standard ATX
- Up to 400watt for Redundant Power
Environment
• Operating temperature
- 0oC ~ 40oC
• Storage temperature
- -20oC ~ 75oC
• Relative humidity
- 10%~90% non-condensing
Vibration
• Sine wave vibration test (non-operating)
- Frequency: 5 - 500 Hz
- Acceleration: 2g
• Random vibration test (operating)
- Frequency: 5 - 500 Hz
- Acceleration: 0.3g
• Random vibration test (packing)
- Frequency: 1 - 200 Hz
- Acceleration: 1.15g
Shock
• Non-OP shock
• RoHS
Acoustic Noise
• ISO 11201:1995(E)/ISO 7779:1999/ Amd.1:2003(E)
Dimensions
• Chassis Dimensions: 426mm x 450mm x 44mm
• Carton Dimensions: 560mm x 620mm x 190mm
Weight
• Without Packing: 8Kg
• With Packing: 12Kg
Certification
• CE
• FCC Class A
• UL
ESD
• 2/4KV contact discharge
• 2/4/8KV air discharge
• Criteria B
Safety
• UL
• LVD

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 4NSA 5130 User Manual
Chapter 1: Product Introduction
Main Board (NSB 5130)
Processor
• CPU
- Intel®2nd generation Core™ processors, Max 95watt
Chipset
• Intel®C206
Memory
• Technology
- DDR3 1066/1333MHz ECC and Non-ECC memory
• Sockets
- Four 240-pin DDR3 DIMM sockets
• Capacity
- 16GB maximum memory
Network
• Onboard LAN controller
- Intel 82583V x8 (connected from Intel 3450 PCIe bus)
• Link speed
- 10/100/1000
• Bypass
- 4 pairs (dual latch bypass, Active Bypass status report)
• Media type
- Copper
• PXE boot
- ETH1 (the left side of LAN)
• LAN module (optional)
- One PCIe x8 connected to CPU PCIe bus
- Supports Nexcom NSK53xx series modules
Storage
• SATA
- Two SATA connectors with power connector for one 3.5” HDD (de-
fault) or two 2.5” HDD (optional)
• SATA DOM
- One SATA DOM connector with power connector (JST 2-pin)
• CompactFlash
- JMicron JMD330 SATA to IDE bridge
- One CompactFlash socket
Status Indicator
• Power LED
- Green: Lights green when the system is On.
• HDD LED
- Yellow: Lights yellow when the HDD is active.
• GPIO LED
- Yellow
• Bypass LED
- Yellow
RTC
• Controller
- Built-in controller
• Backup battery
- Lithium ion battery

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 5NSA 5130 User Manual
Chapter 1: Product Introduction
System Management
• Watchdog
- Watchdog timeout is programmable by software from 1 second/min.
to 256 sec. (from Winbond W83627 Super I/O)
• System Monitor
- Monitors voltages (system temperature sensor, monitors system volt-
age, monitors battery voltage, monitors fan speed of system and
module) (W83792 monitor chip)
- Fan speed controller: 2 fan connectors with fan speed control function
I/O Port
• Internal I/O
- Serial ports: two reserved 2x5 2.0mm box headers (COM1 and COM2)
- USB ports: one 1x6 2.0mm JST connector
- SATA ports: three SATA ports
- PS/2 keyboard/mouse: one 2x4 2.54mm pin header
- GPIO: one 2x2 2.0mm pin header
• Rear I/O
- 1x PCIe x16 slot for a x8 slot on the riser card
- 1x VGA port
- 2x USB ports
• Front I/O
- 2x USB ports
- 1x RJ45 type console port
- 8x RJ45 copper LAN ports
- Power status / HDD status / LAN status / Bypass status LED
- 1x GPIO software button
- 1x LAN module bay (optional)
Expansion
• PCI Express
- One PCIe x8 slot on the riser card
Power
• Connector type
- ATX power connector
• Power mode
- AT mode (default), ATX mode
Use the jumper to change the setting. The BIOS can auto detect the
power mode status.
BIOS
• Flash ROM
- 64MB (SPI)
• Type
- AMI BIOS

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 6NSA 5130 User Manual
Chapter 1: Product Introduction
Software
• Standard OS
- Windows 2003, Linux Kernel 2.6 (Fedora Core, SUSE)
• Drivers
- VGA, LAN, WDT, GPIO, Hardware Monitor, Bypass
• Sample code
- LCM sample string display, LCM testing program, GPIO, WTD, Bypass,
Hardware Monitor
Environment
• Operating Temperature
- 0oC - 40oC
• Storage Temperature
- -20oC - 75oC
• Relative Humidity
- 10%-90% non-condensing
• EMI/EMC
- CE/FCC Class A
• ESD
- 2/4KV contact discharge, 2/4/8KV air discharge, Criteria B

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 7NSA 5130 User Manual
Chapter 1: Product Introduction
Getting to Know NSA 5130
RJ45 type
console LAN port
HDD LED
Power LED
USB ports
Power LED
Indicates the power status of the system.
HDD LED
Indicates the status of the hard drive.
LAN/Bypass Status LEDs
Indicates the status of the LAN/Bypass (F3/F7 bit2 to bit5).
USB Ports
Used to connect USB 2.0/1.1 devices.
Console LAN Port
Used to connect RJ45 type Console port.
GPIO Software Button
This is a GPIO software button.
Copper LAN Ports
Used to connect LAN network devices.
Front Panel
Copper LAN ports
GPIO software
button
Bit2 Bit3 Bit4 Bit5
LAN/Bypass Status LEDs
F3/F7 address