Nieaf EazyVolt I User manual

Voltage Tester
Instruction Manual ʳEazyVolt
҇ & ҈ ʳEV ҇EV ҈

1
TABLE OF CONTENTS Page
1. Safety 2
2. Symbols and Features 3
3. AC/DC V Measurements 4
4. Continuity / Diode Test 5
5. Resistance Measurements 6
6. Single-Pole Phase Tests 6
7. Phase Rotation Test 7
8. RCD Voltage Test 9
9. Illumination 10
10. Battery Replacement 11
11. 4mm Tips Replacement 11
12. Cleaning 12
13. Transport And Storage 12
14. Maintenance 12
15. Specification 13
16. Warranty 15

2
1. Safety
Safety Information
To ensure safe operation and service of the
Tester, follow these instructions.
Failure to observe warnings can result in
severe injury or death.
- Avoid working alone so assistance can
be rendered. If the operators safety can-
not be guaranteed, the Tester must be
removed from service and protected
against use.
- Prior to usage ensure perfect instrument
function (e.g. on known voltage source)
before and after the test.
- Do not connect the instrument to voltages
higher than 690V.
- The safety can no longer be insured if
the Tester :
!shows obvious damage does not carry
out the desired measurements has been
stored for too long under unfavorable
conditions has been subjected to
mechanical stress (i.e. during transport).
- All relevant statutory safety regulations
must be adhered to when using this
instrument.
- The Tester may no longer be used if one
or several functions fail or if no functio-
nality is indicated or the Tester looks
damaged.
- When using this Tester, only the handles
of the probes may be touched do not
touch the probe tips (metal part).
- Do not use the Tester if the Tester is not
operating properly or if it is wet.
- Use the Tester only as specified in the
Instruction card including environmental
conditions and the usage in dry environ-
ments must be followed or the protection
by the Tester might be impaired.
- Use extreme caution when working
around bare conductors or bus bar.
Contact with the conductor could result
in an electric shock.
- Use caution with voltages above 50V
AC rms or 110V DC. These voltages
pose a shock hazard.

3
2. Symbols and Features
Symbols as marked on the Tester
and Instruction manual
!Risk of electric shock
See instruction manual
+ or - + DC or –DC measurement
"Equipment protected by double
or reinforced insulation
Battery
#Earth
AC measurement
$Conforms to EU directives
High Voltage Detection
List of features
-AC Voltage
-DC Voltage
-Continuity
-Resistance (only on EazyVolt II)
-Single pole phase test
-Phase rotation of a three-phase
mains
-Probe tip torch
-Drop proof 1 meter
-IP 64 Protection
-Auto Power On/Offʳ-Selectable probe tips 2/4 mm.
ʳ

4
3. AC/DC V Measurements
AC V
DC V
Reverse polarity with soundʳIf the tester is used in a noisy
background, you need to ensure that the
soundlevel of the tester is perceptible
here.ʳ

5
4. Continuity / Diode Test
Continuity / 
ʳ


The Continuity / test is only possible
when batteries are installed and in good
condition.

6
5. Resistance Measurements
ʳӨ
Only on EV II
The Resistance test is only possible
when batteries are installed and in good
condition.
6. Single-Pole Phase Test
Single-Pole Phase
Firmly Ш

7
The single-pole phase test is only
possible when batteries are installed and
in good condition.
!The single-pole phase test is not
always appropriate for testing whether
a circuit is not live. For this purpose, the
bipolar test is required.
To determine external conductors
during phase tests the display function
may be impaired (e.g. for insulating body
protection or insulating sites).
Firmly grasp the insulated grips of the
Tester probe L2 it is better for increase
the sensitivity of single-pole phase test.
7. Phase Rotation Test
Rotary phase of a three-phase
mains
Right rotary field
Firmly Ш

8
Left rotary field
Firmly ШTesting of phase-sequence direction
is possible from 100V AC voltage (phase
to phase) provided the neutral is earthed.
On making contact with both test elec-
trodes (probe tips) to two phases of the
three-phase power supply which are
connected in clock-wise rotation, a “”
symbol appears in the LCD Display.
If the rotation is anticlockwise, then a “”
symbol is displayed. In this case both
phases of the unit should be switched
around.
Note :
Testing the phase rotation always
requires a negative phase rotation test!
To ensure a connect test, it is better to
test on a known source.

9
Attention :
Please ensure that the test electrodes
(probe tips) make good contact with two
phases of a three-phase mains while test-
ing the phase rotation. For absolute deter-
mination of a clock-wise phase rotation it is
necessary to make a negative phase rota-
tion test after changing the phases. The
indication “” or “” can be affected by
unfavorable light conditions, by protective
clothing or in insulated locations.
Firmly grasp the insulated grip of the
Tester probe L2, it is better for the
sensitivity of the phase rotation test.
8. RCD Voltage Test
Voltage Test with RCD Trip Test
During voltage tests in systems equipped
with RCD circuit breakers, a RCD switch
can be tripped at a nominal residual current
of 10mA or 30mA by measuring the voltage
between L and PE.
These Testers EV҇/ EV҈are equipped
with an internal load enabling the tripping
of an RCD protection device of 10mA or
30mA.

10
To avoid RCD tripping, a test has to be
carried out between L and N during approx.
5sec. Immediately afterwards, voltage test-
ing between L and PE can be carried out
without RCD tripping.
9. Illumination ʳ
Probe tip torch ʳ

11
10. Battery Replacement
If no signal sound is audible (EV҇)when
short circuiting the test probes, if the
symbol “” is displayed (EV҈)
-Completely disconnect EV҇/ EV҈from the measurement circuit.
-Unscrew the screw by a cross screw
driver, then open the battery cover.
-Remove discharged batteries.
-Replace by new batteries, type 1.5V
IEC LR03 by respecting correct polarity.
-Close the battery cover and re-screw the
screw.
“+”
“-”
11. 4mm Tips Replacement
tightenʳunscrewʳ

12
12. Cleaning
Prior to cleaning, remove the instruments
from all measurement circuits. If the
instruments are dirty after daily usage, it is
advisable to clean them by using a damp
cloth and a mild household detergent.
Never use acid detergents or dissolvent
for cleaning. After cleaning, do not use the
voltage tester till it is dried completely.
13. Transport and Storage
In order to avoid instrument damage,
it is advised to remove batteries when not
using the instrument over a longer period.
The tester must be stored in dry and closed
areas. In the case of an instrument being
transported in extreme temperatures, a
recovery time of minimum 2 hours is
required prior to instrument operation.
14. Maintenance
Unauthorized persons shall not disassem-
ble the tester and the supplementary
equipment.
When using tester EV҇/ EV҈testers in
compliance with the instruction manual, no
particular maintenance is required.
If functional errors occur during normal
operating, our service department will
check your instrument without delay.

13
15. Specification
Nieaf Instruments EV I EV II
Voltage range 6….690V AC/DC
LED/Bargraph
resolution 6,12,24,36,50,120,
230,400, 690V
LCD voltage range 10V…690V
AC/DC
LCD resolution 1V
Accuracy (3%rdg+2d)
Voltage detection Automatic
Acoustic signal sound (AC Voltage) Yes
(“—”DC Voltage) Yes
Polarity detection Full range
Range detection Automatic
Response time <0.1s <0.1s/BAR
<2s/RDG
Frequency range DC, 45…65Hz
Automatic load (RCD) Yes
Peak current Is <0.2A / Is(5s) <3.5mA
Operation time ED (DT)=30s.
Recovery Time 10 min.
Auto Power On <12 VAC / DC
Single-pole Phase Test
Voltage range 100…690V AC
Frequency range 45…65Hz
Resistance Test
Resistance Range
Accuracy
Test Current
0…2KӨ(3%rdg + 10d)
< 0.5mA

14
Nieaf Instruments EV I EV II
Continuity Test
Threshold < 200KӨTest current < 20µA
Overvoltage
protection 690V AC/DC
Rotary Field Indication
Voltage range (LEDs) 100…690V
Frequency range 50…60Hz
Measurement
principle
Double-pole and firmly
hold the grip (L2)
Power supply 2 x 1.5V Micro IEC LR03
Power consumption Max. 30mA / approx.
250mӨTemperature -10ºC…55ºC
Humidity Max. 85% relative
humidity
Height above sea
level
Up to 2000m
Overvoltage class CAT III / 1000V
CAT IV / 600V
Pollution Degree 2
Type of protection IP64 / IP65 pending
CE EN61326 :
EN55011 :
SafetyʳEN61010-1 : 2001
EN61010-031 : 2002
EN61243-3 : 1998
EN61243-3/CI : 2000
EN60529 : 1992/AI2000
GS38
Functionality
ʳʳCertificationʳEN61243-3 : 1998
EN61557-7 : 1997
EN61557-10 : 2001
EN 61557-1 : 1997
KEMA / VDE ʳCSA / UL pending
Weightʳ230g (EVI), 240g (EVII),
(incl. Batteries)ʳDimensionsʳ245x61x36mmʳ

15
16. Warranty
Nieaf Instruments are subject to strict
quality control. However, should the
instrument function improperly during
normal use, you are protected by our
6 month warranty.
We will repair or replace free of
charge any defects in workmanship
material, provided the instrument is
returned unopened and unhampered
with.
Damage due to dropping or incorrect
handling is not covered by the war-
ranty.
If the instrument shows failure follow-
ing expiry of warranty, our service
department can offer you a quick and
economical repair.