Night & Day Furniture SHOE FITTINGS Bronze User manual

Back Deck Bottom Roller (Code A1)
Parts Packed in this Box. Full and Queen size only:
Strong Back assembly.
Page 1 of 5
Chair • Love seat • Full • Queen
Futon Body Assembly
1A 1B
Please Note: The parts shown below are Full size.
The other sizes differ only in overall length.
Back Deck
Seat Deck
Stretchers x 2 pieces
Seat Deck Pin (Code A3)
Back Deck To p Roller (Code A2 )
Use the Short Bolts (40mm)
To attach the Strong
Back to the Back
Deck.
Assembly Instructions
ND 1004
SHOEFITTINGSTM
US Patent #6,715,166
Other Patents Pending
Bronze
SHOE F ITTINGSTM
Snapper Snapper
Queen size only: Extra parts in this box.
1C
Short Legs
x 2 pieces
50mm Bolts
x 2 pieces
40mm Bolts
x 4 pieces
Allen Key
x 1 piece
Strong Back x 1 piece
featuring the Rubber TM
TM

Attach Stretchers to Arms
Prepare Arms for Assembly.
2A 2B Attach Arms to Stretchers.
Page 2 of 5
Using Bolts and Barrel Nuts provided with the Arms,
attach the Arms LOOSELY to the Stretchers as shown..
It is important that these bolts are left LOOSE!
Rear stretcher (no plates )
The Front Stretcher has metal plates which should face upwards.
Fasten Stretcher Brackets to the Arms:
Fit Wooden Dowels to
Stretchers:
Assembly Instructions
ND 1004
Chair • Love seat • Full • Queen
Bronze
SHOE F ITTINGSTM
NOTE: The hardware for these steps is
included .in the ARM box.
Cleat
Stretcher
Bracket
Hole for Cleat
Leg
Dowel Hole
16mm Bolt
Allen Key
Hole for Bolt
A. Insert the Stretcher Bracket Cleat into the
hole provided.
B. IMPORTANT: Don't fully tighten Bracket until
Stretchers are all in place for easy alignment.
Ta p dowels all the way into the middle
hole at each end of the Stretchers.
Wooden Dowel
Stretcher
Middle
hole
THIS END
FRONT
Wooden
Dowel
Barrel Nuts
Allen Key -
Leave bolts LOOSE!
Bolts
Bolts
Bolts
Do not tighten
the Bolts at
this stage!
Be sure the holes
are
free of wood chips
and saw dust.
Do not force the Bolt
as you may strip the
thread. Be sure the
thread is properly
started.
Barrel Nut
Bolt
Allen Key Screwdriver
BOLT AND BARREL
NUT
ASSEMBLY SYSTEM
Insert Barrel Nuts as shownusing a
screwdriver. This will help you position
the Nut in line with the Bolt.
Bolt

Chair • Love seat • Full • Queen
Fit the Back Deck into Position:
3A
Page 3 of 5
Fit the Back Deck
CAREFUL !
These can
Scratch the
Arms
Your arm style may vary
Tighten all the Bolts.
Assembly Instructions
ND1004
Bronze
SHOE F ITTINGSTM
Tighten all the Bolts.
Use 2 People!
Please Note:
Remember that the Bolts on the Arm should be LOOSE.
Be careful not to scratch the Arms with the Plastic
Runners when you lower the ends of the Back Deck.
Insert the Back Deck lying
flat. Insert one end first, then
gently lower the other end into position.
When you have the Back Deck fitted
lying flat, tighten all the Bolts.
Tighten all the Bolts.
3B
For Queen size frame only:
Attach the short legs.
3C
All four joints must
be left LOOSE.
50mm Bolt
The exposed part of the metal nut
in the leg should be oriented away
from the bolt for proper assembly.
Using the extra 50mm bolts, attach
the Queen short legs to the back deck.
Queen
short leg

Fit the Seat Deck
Hook the Seat Deck onto the Snapper.
4A Pull the Seat over the "Snap Point." 4B
Push down on the Seat, and the
Back will Lift.
4C This is the Lounge Position. 4D This is the Sofa Position. 4E
Page 4 of 5
Lift the Seat Deck in vertically, so the Pins
meet with the Rubber Snapper. The head of
the Snapper should fit between both Pins.
With the To p Pin
inside the notch on
the Rubber Snapper, put
your foot on the Back Deck
and pull the Seat over the "Snap Point"
Put your
foot here
You will need to Pull Hard.
Push the Seat
down further and the
Back will rise until it is
in the "Lounge Position"
Push the Seat
with your knee, to
convert to the Sofa Position
Push
Add Mattress and
Enjoy! See separate page
for Operating Instructions.
•The To p Pin - fits over the top,
•The Lower Pin - goes underneath.
Just remember:
Use 2 People!
Please Note:
Assembly Instructions
ND 1004
Chair • Love seat • Full • Queen
Bronze
SHOE F ITTINGSTM
- over the top
Bottom Pin Notch
To p Pin
Rubber
Snapper
- underneath

Use 2 People!
Please Note:
From the Back, lift out the To p Pin and ease the Seat Deck forward.
Push the Seat over the "Snap Point."From the Bed position, lift the Seat.
5A Lift the Seat all the way. 5B 5C
5D Lift the Seat clear of the frame. 5E
Page 5 of 5
You will need to Push Hard.
Lift from the front,
using both Handles.
Lift all the way until the
To p Pin drops into the
notch on the Rubber Snapper.
Lift and ease the Deck forward
Lift up so the To p Pin is out of
its notch in the Rubber Snapper.
Ease the Back Deck forward,
keeping it orientated vertically.
Be careful when lifting the
Seat Deck out, not to scratch
the Arms with the Rollers.
Disassembly: Removing the Seat
Assembly Instructions
ND 1004
Chair • Love seat • Full • Queen
Bronze
SHOE F ITTINGSTM
To p Pin
Notch
Rubber
Snapper
Rubber
Snapper