Nikon KeyMission 80 User manual

SB6K01(11)
6MN72211-01
En Wi-Fi Connections (iOS)
Read this guide for information on using SnapBridge for Wi-Fi connections on iOS devices.
Why Is the Wi-Fi Prompt Displayed?
Why Is the Wi-Fi Prompt Displayed?
The Wi-Fi prompt is displayed when:
• SnapBridge switches from Bluetooth to Wi-Fi.
SnapBridge automatically switches between
Bluetooth and Wi-Fi to save power. The Wi-Fi
prompt is displayed when SnapBridge switches
from Bluetooth to Wi-Fi. Note that SnapBridge
may need a few seconds to switch to Wi-Fi after
you perform such operations as selecting remote
photography in the Camera tab.
• SnapBridge detects the camera after losing the Wi-Fi
connection. The connection will be lost when
your iOS device locks or the camera enters
sleep mode, in which case your device may
automatically connect to another network.
The Wi-Fi prompt will be displayed as needed
when SnapBridge detects the camera again.
The Wi-Fi connection may also be lost due to
strong interference or as a result of exiting the
SnapBridge Camera tab.
Trademark Information
Trademark Information
• The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Nikon
Corporation is under license.
• iOS is a trademark or registered trademark of
Cisco Systems, Inc., in the United States and/or
other countries and is used under license.
• Wi-Fi and the Wi-Fi logo are trademarks or
registered trademarks of the Wi-Fi Alliance.
The Wi-Fi Prompt
The Wi-Fi Prompt
A Wi-Fi prompt will be displayed when SnapBridge
requires a Wi-Fi connection. Follow the steps
below to connect to the camera via Wi-Fi.
1 Tap Go when prompted.
2 Tap <Settings to display
iOS settings.
3 Tap Wi-Fi.
4 Tap KM80_XXXXXXXX.
5 Enter the camera
password if prompted
(the default password is
“NikonKeyMission”).
DChanging the Default Password
We recommend that you change the default password
to protect your privacy. The password can be changed
by pressing the camera Gbutton to view the Home
display and selecting Camera settings> Network
menu> Wi-Fi> Network settings in the (setup)
menu.

Connection Issues
Connection Issues
If you are unable to use remote photography or
download selected images even after pairing the
camera with the iOS device and establishing a
Wi-Fi connection, try:
• switching tabs in SnapBridge,
• quitting and restarting SnapBridge, or
• ending pairing, telling your device to “forget” the
camera, and then pairing with the camera again
Re-establishing Pairing
Re-establishing Pairing
Follow the steps below to end and re-establish
paring.
1 Open the Connect
tab, select Connection
options, and tap End
pairing. After ending
pairing, quit the app
completely by double-
clicking the Home
button and swiping up
to dismiss SnapBridge.
2 Open the iOS settings
app and tap Bluetooth.
3 Tap the icon to the
right of the camera
name.
4 Tap Forget This Device.
5 Press the camera Gbutton to view the Home
display, then select Camera settings> Network
menu> Connect to smart device in the (setup)
menu and follow the on-screen instructions to
initiate pairing.
6 Start SnapBridge and tap
Connection options in
the Connect tab.
7 Tap the camera name.
8 When prompted to
select an accessory, wait
for the Bluetooth icon at
the top right corner of
the display to turn from
white to gray and then
tap the camera name.
Wait until icon turns gray.
Tap camera name.
9 !This step involves both the camera and the iOS
device. Have them ready side-by-side before
proceeding.
After checking the authentication code, tap the
OK on the camera and tap the SnapBridge Pair.
The dialog at right will be
displayed when pairing
is complete.
!If you wait too long between tapping the
button on the camera and tapping the
button in SnapBridge, pairing will fail and
an error will be displayed.
• iOS device: Quit the SnapBridge app
completely by double-clicking the
Home button and swiping up to dismiss
SnapBridge, then return to Step 1.
• Camera: Tap OK. After a short pause, a
dialog will be displayed; tap Reconnect
and return to Step 5.