Nista Devices IP39-40PC User manual

NISTA DEVICES GmbH 2013 ©All Rights Reserved
1
Door Access Control with the VoIP interface
Release 1.4

NISTA DEVICES GmbH 2013 ©All Rights Reserved
2
IP Door Phones
IP39-4X
Quick Installation Guide
Document Release: 1.04
Release Date: 18-Jun-15

NISTA DEVICES GmbH 2013 ©All Rights Reserved
3
NOTICE
This document refers to the Nista Devices GmbH Door Access Control devices with VoIP protocol capabilities.
Additional copies of this manual may be obtained from Nista Devices GmbH. Reproduction of this manual or parts thereof without written
permission from Nista Devices GmbH is strictly prohibited.
Nista Devices GmbH reserves the right to modify the hardware and software described herein without prior notice. However, changes made to the
hardware or software described do not necessarily render this publication invalid.

NISTA DEVICES GmbH 2013 ©All Rights Reserved
4
Table of Contents
1Introduction ................................................................................................................................................................5
1.1 List of Available Models ....................................................................................................................................5
2The IP Door Phone kit contents.................................................................................................................................5
3Installation..................................................................................................................................................................6
3.1 Physical installation...........................................................................................................................................6
3.2 IP Door Phone installation.................................................................................................................................6
4Access to WEB Programming ...................................................................................................................................9
5Reset device to Factory Default Configuration ........................................................................................................15

NISTA DEVICES GmbH 2013 ©All Rights Reserved
5
1 Introduction
To avoid damage to the Door Phone, the external power supply and POE
Ethernet connection should be disconnected from mains prior to
connecting wires to the Door Phone unit.
The External Power Supply does not included in standard IP394X
package
1.1
List of Available Models
Model
Description
IP39-40PC
IP Door Phone, Piezo Keypad, Integrated Internal Video Camera
IP39-40P
IP Door Phone, Piezo Keypad
IP39-41PC
IP Door Phone, Piezo Single Button, Integrated Internal Video Camera
IP39-41P
IP Door Phone, Piezo Single Button
IP39-40AC
IP Door Phone, Touch Keypad, Integrated Internal Video Camera
IP39-40A
IP Door Phone, Touch Keypad
IP39-41AC
IP Door Phone, Touch Single Button, Integrated Internal Video Camera
IP39-41A
IP Door Phone, Touch Single Button
2 The IP Door Phone kit contents
IP394X Package content:
IP Door phone unit
Rear metal cover
Rear rubber mat
Set of terminal connectors
Hex key wrench for security screw
Note:
1. Device is optionally available for orders with the internal wide-angle digital video camera.
The Video camera must be order separately.
2. Allowed to use External Power Supply if a customer’s LAN doesn’t support POE ( Power Over Ethernet)
functionality. External Power Supply shall respond to follow technical requirements:
Input: 100 –240 V AC
Output: 5V DC; 2A
5V DC Power supply output shall be connected to IP Door Phone in accordance with required pins
polarity
3. The External Power Supply does not included in standard IP394X package

NISTA DEVICES GmbH 2013 ©All Rights Reserved
6
3 Installation
3.1 Physical installation
The Door phone can be mounted on the wall by using installation bracket provided with the unit.
To install the IP Door Phone Unit on the wall:
Open the IP Door Phone case by rotating the secret screw from the bottom side of the unit.
Figure 3-1 Door Phone wall installation
To install the wall bracket:
1. Measure and mark the location of the holes on the wall, where they are to be drilled.
2. Drill the holes and insert the wall dowels into the holes.
3. Place the rubber membrane on the wall and then metal unit base using the provided wall screws.( See Figure 3-1)
4. Connect all required wired connections
5. Put the Door Phone’s front panel into the base latch mechanism, then close the case and lock with the any tamper
screw.
3.2 IP Door Phone installation
The IP Door Phone can be installed as an individual access control device.
Figure 3-2 shows the terminal locations on the wire connector provided with the unit. This connector is then inserted
into the mating connector located at the base of the internal PCB. All wiring to the unit shall be attached to the wire
connector.
The Ethernet RJ-45 socket is for the LAN network cable and PoE connection.

NISTA DEVICES GmbH 2013 ©All Rights Reserved
7
The wiring connector has screw connector type terminals. In order to attach a wire, you must insert the stripped end of
the wire into the appropriate wiring connector socket and tighten the terminal screw. This will bring together the wire
connection.
To avoid damage to the Door Phone, the external power supply ( id used
) or POE Ethernet should be disconnected from mains prior to connecting
wires to the Door Phone unit.
The External Power Supply does not included in standard IP394X
package
Figure 3-2The IP Door Phone PCB Module
1. Remove the front panel cover from the Door Phone unit and find the wiring connector on the PCB module. ( See
Figure 3-2 )
2. Connect the door-lock relay wires to “Relay 1”/ “Relay 2”terminals.
Note:
1. Draw attention on NO/NC jumper position. The closed ‘Center’ Pin +’NO’ pin means the ‘Normally open’
relays status in powered mode. The closed ‘Center’ Pin +’NC’ pin means the ‘Normally Close’ relays
status in powered mode
2. Important: To set device in operational mode, switch 1 on PCB shall be switched to
position “Normal”. ( See Figure 3-2 )
3. If an external switch button is used ( See Web GUI Door Functions -> Sensor -Chapter Error! Reference
ource not found.), connect the button wires to the “Sensor 2”and the “Sensor 1”terminals.
4. Plug the wiring connector to the Door Phone PCB module.

NISTA DEVICES GmbH 2013 ©All Rights Reserved
8
5. Attach the Door phone into the installation bracket.
6. Check the LAN network cable is inserted into the ‘Ethernet’ RJ-45 socket and that if PoE is deployed the unit
powers up.
7. If an external power supply is used , switch on the external power supply pins DC5V.
Note:
1. The IP Door Phone internal relay’s maximum supported electrical current is 2A
2. Important: To set device in operational mode, switch 1 on PCB shall be switched to position “Normal”. (
See Figure 3-2 )
Connector’s PINs
Description
1 ( SW2)
Factory Default Settings switch:
‘Normal’ – Door Phone normal working position
‘Default’ – Set to default procedure mode
2
Hardware Reset ( Cold Reset Switch)
3 ( NO/NC Jumper)
Relay 1 and Relay 2 Normally Open and Normally Close status jumper.
Closed Central Pin (2) + ’NO’- (1) pin means the ‘Normally open’ mode.
Closed Central Pin (2) + ’NC’ - (3) pin means the ‘Normally Close’ mode
Note: Relay 2 works in Normally Open (NO) mode only
4
Microphone Connector
5
Speaker Connector
6- Ethernet
POE/LAN connection
5VD (5V DC)
External power supply 5VDC 2A input (if no POE applied).
Draw attention on connection polarity: +5V and GND marked on PCB
(Figure 3-2)
The External Power Supply does not included in standard IP394X package

NISTA DEVICES GmbH 2013 ©All Rights Reserved
9
Connector’s PINs
Description
SEN 1/2 (Sensor 1/2*)
Door status detector.
Also can be used as external Switch button connection (Chapter Error!
eference source not found.). Note: The short circuit closer type External
Switch button can be used for manual door opening
REL 1/2 (Relay 1/2)
Support 30VDC 2A
Internal relays Normally Open and Normally Close status depends on JP1
jumper position.
Audio Out*
Reserved for future release
Note: * - Listed feature support depends on IP Door phone firmware release
Figure 3-3 IP394X Connections
Note:
The door electrical Lock requires separate powering follow by door lock manufacture’s requirements
4 Access to WEB Programming
1. The unit comes configured with the default IP address: 10.10.10.6 . To access to the unit’s WEB programming if
your LAN configured with different subnet please make following:
2. On Windows 7 PC:

NISTA DEVICES GmbH 2013 ©All Rights Reserved
10
Go to Control Panel
Open ‘Network and Sharing Center’
Click on ‘Change adapter settings’
Mouse right click on active Ethernet connection and chose ‘Properties’

NISTA DEVICES GmbH 2013 ©All Rights Reserved
11
In LAN properties window select ‘Internet Protocol Version 4 (TCP/IPv4) option and click on
‘Properties’ button
Select 'Use the following IP address:' and insert IP Address and Subnet mask as shown on the
picture below

NISTA DEVICES GmbH 2013 ©All Rights Reserved
12
Press ‘OK’ to accept settings
3. Launch Internet browser and type 10.10.10.6 in address bar.
4. Log in to the Nista web GUI using the appropriate user’s credentials
IP 394X provides different management levels for WEB-Management: Administrator and User
‘Administrator’ level has access to all IP394X configuration parameters
‘User’ level has limited access to IP394X configuration parameters.
Fill Administrator or User login name and Password fields.

NISTA DEVICES GmbH 2013 ©All Rights Reserved
13
Note:
1. The default IP Door Phone IP address is 10.10.10.6 and it is configured as ‘Static’ IP Address.
2. The default web-programming Administrator credentials are:
User name: ‘admin’ –For Administrator management level and ‘user’ –for User management level
Default Password: 1234 for both management levels
3. It is strongly recommended to change the default administrator password to a stronger one. Allowed Password
characters: Up to 19 Digits: 0-9, Aa-Zz, no space allowed
4. Also IP Door phone IP address could be seen on the unit’s LED display (keypad models only).
Dial: P/ + 1 + Web Access Administrator password + #
5. Go to ‘Network’ then click on ‘LAN' and configure IP394X network parameters
6. Press Apply button and then ‘Save & Reboot ‘ menu option
7. Return to Windows 7 PC Network adapter properties and set IP address and Subnet mask to the original

NISTA DEVICES GmbH 2013 ©All Rights Reserved
14
Configure the rest of parameters by using the IP Door Phone User’s manual document

NISTA DEVICES GmbH 2013 ©All Rights Reserved
15
5 Reset device to Factory Default
Configuration
IP Door phone can be reset to its Factory default configuration by using following actions:
1. Via WEB-Management interface ( See Chapter 7.8 in User Manual document)
2. By using the hardware ‘Factory Default Settings’ switch ( See Figure 3-2 )
To set IP Door Phone to Factory Default Setting by using hardware ‘Factory Default Settings’ switch:
Power off the device.
Put the switch to “DEFAULT” position.
Power on this device will restore the factory default.
oLED Display can show the message “ Destination not set “ if Day or Night destinations not specified
and device’s case is open
oLED Display Shows’ Set to default’ message if a case is closed
o
Power off the device.
Put the switch back to “NORMAL” position
Power on the device
Figure 5-1 Factory Default Settings switch SW2