Brief Introduction
The LHH82 is a lens heater specially designed for camera lenses with a lter
size of 72~82mm to protect it from fogging and blurring the images. It is
equipped with an intelligent thermal control module to warm up the lens to
a temperature of approx. 45°C (113°F). It is powered by an external USB
power supply and withstand an extremely low temperature of -40°C (-40°F).
It has 4 heating zones with hook-and-loop design for quick installation and
dismount in various environments.
Technical Specications
Input 5V⎓2A (MAX)
Input Port USB-C
Operating Temperature -40°C~40°C (-40°F~104°F)
Heating Temperature 45±5°C (113±9°F)
Compatible with
Camera lenses with a lter size of 72~82mm
Including Canon EF 70-200mm f/2.8L IS III USM and more
Main Materials 1680D Nylon
Dimensions Zone 1: φ85mm (φ3.35")
Zone 2~4: 394mm×168mm (15.51"×6.61")
Weight 190g (6.70oz)
Accessories USB Charging Cable (USB-A to USB-C, 1.5m)
Note:
1. The heating temperature is tested in NITECORE Lab for reference only.
The data may vary in real world use due to dierent environmental
conditions.
2. Please refer to the lter size for more compatible models.
Operating Instructions
As illustrated, after wrapping up the camera lens, use the USB cable to
connect an external power supply (e.g. a power bank or other USB charging
devices) to the charging port to begin the heating process. After that, the
blue indicator beside the input port will turn on steadily.
• After connecting the power supply, the heating process will start
automatically without manual settings.
• The product will start to heat up Zone 2 rst. After Zone 2 reaches
approx. 45°C (113°F), it will then start to heat up Zone 1, 3 and 4
simultaneously.
Warnings
1. Please read the user manual carefully before using the product.
2. Please use the USB charging cable included and high-quality power
banks to power the product. It is recommended to use ocial
NITECORE power banks (sold separately).
3. DO NOT use the product in an environment of -20°C (-4°F) or lower for
over 6 hours, as the USB charging cable could be damaged due to low
temperature.
4. Please connect the applicable external power supply only according to
the specications in this user manual. Insucient input power may lead
to malfunction of the product.
5. DO NOT expose the product in the rainy or moist environment. Keep it
away from any combustible material.
6. The product is only to be used by adults above 18 years old. Children
under this age must be supervised by an adult when using the product.
7. Please unplug the product when it is left unused.
8. DO NOT puncture the product.
9. DO NOT expose the product to corrosive liquid.
10.
Please clean the product with a soft brush. DO NOT rinse it with water.
11. DO NOT leave the product unattended when it is in use. Stop using the
product at any sign of malfunction.
12. DO NOT disassemble or modify the device as doing so will render the
product warranty invalid. Please refer to the warranty section in the
manual for complete warranty information.
13. DO NOT misuse in any way! Use for intended purpose and function only.
Disclaimer
This product is globally insured. NITECORE shall not be held responsible or
liable for any loss, damage or claim of any kind incurred as a result of the
failure to obey the instructions provided in this user manual.
Warranty Service
All NITECORE®products are warranted for quality. Any DOA / defective
product can be exchanged for a replacement through a local distributor/
dealer within 15 days of purchase. After that, all defective / malfunctioning
NITECORE®products can be repaired free of charge within 12 months
from the date of purchase. Beyond 12 months, a limited warranty applies,
covering the cost of labor and maintenance, but not the cost of accessories
or replacement parts.
The warranty will be nullied if
1. the product(s) is/are broken down, reconstructed and/or modied by
unauthorized parties;
2. the product(s) is/are damaged due to improper use.
For the latest information on NITECORE®products and services, please
contact a local NITECORE®distributor or send an email to
※
All images, texts and statements specied herein this user manual are
for reference purposes only. Should any discrepancy occur between
this manual and information specied on www.nitecore.com, Sysmax
Innovations Co., Ltd. reserves the rights to interpret and amend the
content of this document at any time without prior notice.
Thanks for purchasing NITECORE!
SYSMAX Innovations Co., Ltd.
TEL: +86-20-83862000 FAX: +86-20-83882723
Address: Rm 2601-06, Central Tower, No.5 Xiancun Road,
Tianhe District, Guangzhou, 510623, Guangdong, China
Please nd us on facebook: nitecorephotoaccessory
LHH07048221
Made in China
LHH82 LENS HEATER
USER MANUAL
IMPORTANT NOTICE CONCERNING WARRANTY SERVICE
Thank you for purchasing! Before using this product, please nd your verication code on the package box, and go to http://charger.nitecore.com/
validation (or scan the QR code beside the verication code to visit on your mobile phone). Type in your verication code and personal information as
required, and submit the page. After verication, NITECORE will send you a warranty service email. This email and your registration email address are
essential to your possible warranty application. Before you complete the warranty service registration, you cannot enjoy our warranty service for your purchase.
