Nitrous Outlet 00-66000 User manual

Remote Bottle Opener
PART NUMBER 00-66000 and 00-66000-K
INSTALLATION INSTRUCTIONS
WWW.NITROUSOUTLET.COM/INSTALLATION-GUIDES
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 | P: 254-848-4300 | WWW.NITROUSOUTLET.COM
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
©N2O013020
INSTALLATION INSTRUCTIONS
This Nitrous Outlet Remote Bottle Opener is designed to provide an easy way to remotely open and close your Nitrous Outlet Bottle. This item is compatible
only with the Nitrous Outlet Billet High Flow Valve.If this opener is for the Nitrous Outlet X-Series BottleValve, you will need an adapter (P/N 00-66000-sleeve).
If you need any assistance during installation or if you have questions about this item, call our Tech Help Line at [phone].
Tools Needed for Installation*:
• 1/2” Wrench • Drill • 13/16” Drill Bit • Wire Crimper • 3/16” Allen Wrench • Ratchet
Parts List:
• Billet Housing with Motor Collar • Collar Bolt Gear • Rubber Grommet • Thumb Screw • 6 x Mini Push-On Terminal
• Mini Rocker Momentary Switch • 2 Wire Weather Pack Connector • Red Butt Connector •Red Ring Wire End
• Yellow Butt Connector • Yellow Ring Wire End • Washer
*These are the tools required for installation of this kit on a stock vehicle. If your vehicle has aftermarket parts, other tools may be required.
Step 1:
Remove the plastic cap on top of the bottle valve, and remove
the On/Off knob with a 1/2” socket and ratchet.
Step 2:
Loosen the bolt on the collar with a 3/16” Allen Wrench.
Then, place the collar on top of the bottle valve and ensure
it’s sitting all the way down on the bottle valve. Then, tighten
the collar bolt with a 3/16” Allen Wrench.
***In the event you need the remote opener in a certain orientation, loosen the Collar
and rotate it to the position you need it to be in.***
Step 3:
Place the remote opener gear on the bottle valve, and ensure
it’s completely seated. Then, secure the Remote Opener Gear
using the nut that held the On/Off knob. Tighten it down with
a 1/2” Socket and Ratchet.

Remote Bottle Opener
PART NUMBER 00-66000 and 00-66000-K
INSTALLATION INSTRUCTIONS
WWW.NITROUSOUTLET.COM/INSTALLATION-GUIDES
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 | P: 254-848-4300 | WWW.NITROUSOUTLET.COM
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
©N2O013020
Step 4:
Put the Remote Opener Motor on the bottle valve. The
gears inside the Remote Opener will need to align for the
motor to sit down completely. If the motor does not sit down
completely, turn it slightly and try again.
Step 5:
Line up the bolt holes on the Remote Opener Collar
and Motor.
Step 6:
Thread the Thumb Screw into the bolt hole on the Remote
Opener Motor to secure the opener to the bottle valve.
Step 7:
The bottle and remote opener are now ready for installation
into the vehicle. Use the attached wiring digram to complete
the installation process.

Remote Bottle Opener
PART NUMBER 00-66000 and 00-66000-K
INSTALLATION INSTRUCTIONS
WWW.NITROUSOUTLET.COM/INSTALLATION-GUIDES
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 | P: 254-848-4300 | WWW.NITROUSOUTLET.COM
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
©N2O013020
Wiring Diagram
Now that your Remote Bottle Opener is installed, you can begin wiring it. When wiring your Remote Bottle Opener, double check
all of your wiring connections. For a clean, professional install we rec-ommend using heat shrink of all crimped connectors.
This will protect the connection, and make the connection stronger between the wire and crimp-on connector.
If you have any questions regarding the installation or operation of your Nitrous Outlet Switch Panel, please call the Nitrous Outlet
Tech Support Line at [phone]. We are available to answer your questions or concerns Monday-Friday, 8:30am-5:30pm CST.
Tips From The Pro’s
When wiring your switch panel, double check all of your wiring connections. For a clean, professional install we recommend
using heat shrink of all crimped connectors. This will protect the connection, and make the connection stronger between the
wire and crimp-on connector.