Nobles 608622 Product manual

ENGLISH - ESPAÑOL
Battery Automatic Scrubber
Fregadora Automática Batería
Speed Scrubt2001
Model No.:
608622
608623 – Pac
609243 – Can. Pac
608624
Rev. 01 (11-01)
CUSTOMER SERVICE: 1-800-365-6625
FAX: [phone]
NOBLES
12875 RANSOM STREET
HOLLAND MI 49424 U.S.A.
Operator and Parts Manual
Manual de Operación y de Piezas

OPERATION
2SpeedScrubt2001 Battery (11–01)
This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing.
When ordering replacement parts, use the parts lists
section in this manual. Before ordering parts or
supplies, be sure to have your machine model number
and serial number available. Parts and supplies may
be ordered by phone or mail from any Authorized
Service Center or Distributor.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
maintenance instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Please fill out at time of installation for future reference.
ModelNo.-
Install. Date -
Serial No.-
E2001 Tennant Company Printed in U.S.A
Specifications and parts are subject to change without notice.
Nobles and Speed Scrub are registered United States trademarks of
Tennant Company.
TABLE OF CONTENTS (ESPAÑOL ÍNDICE....17)
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . .
MACHINE COMPONENTS 4. . . . . . . . . . . . . . . . . . .
MACHINE INSTALLATION 5. . . . . . . . . . . . . . . . . . .
UNCRATING MACHINE 5. . . . . . . . . . . . . . . . . .
INSTALLING BATTERIES 5. . . . . . . . . . . . . . . .
MACHINE SETUP 6. . . . . . . . . . . . . . . . . . . . . . . . . .
PRE–OPERATION CHECKS 6. . . . . . . . . . . . . .
ATTACHING SQUEEGEE 6. . . . . . . . . . . . . . . .
INSTALLING BRUSH OR PAD DRIVER 6. . . .
FILLING SOLUTION TANK 7. . . . . . . . . . . . . . .
MACHINE OPERATION 8. . . . . . . . . . . . . . . . . . . . .
WHILE OPERATING MACHINE 9. . . . . . . . . . .
BRUSH MOTOR CIRCUIT BREAKER 9. . . . . .
DRAINING TANKS 10. . . . . . . . . . . . . . . . . . . . . . . . . .
DRAINING RECOVERY TANK 10. . . . . . . . . . . .
DRAINING SOLUTION TANK 10. . . . . . . . . . . . .
BATTERY CHARGING 11. . . . . . . . . . . . . . . . . . . . . .
MACHINE MAINTENANCE 12. . . . . . . . . . . . . . . . . .
DAILY MAINTENANCE 12. . . . . . . . . . . . . . . . . . .
WEEKLY MAINTENANCE 12. . . . . . . . . . . . . . . .
MONTHLY MAINTENANCE 12. . . . . . . . . . . . . . .
QUARTERLY MAINTENANCE 12. . . . . . . . . . . .
BATTERY MAINTENANCE 12. . . . . . . . . . . . . . .
TRANSPORTING MACHINE 13. . . . . . . . . . . . . . . . .
STORING MACHINE 13. . . . . . . . . . . . . . . . . . . . . . . .
RECOMMENDED STOCK ITEMS 13. . . . . . . . . . . . .
TROUBLE SHOOTING 14. . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 16. . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL DIAGRAMS 32. . . . . . . . . . . . . . . . . . . .
PARTS LIST 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPLACEMENT BRUSHES AND PAD DRIVER
GROUP 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOLUTION TANK GROUP 36. . . . . . . . . . . . . . . .
SOLUTION TANK REAR PANEL GROUP 38. .
RECOVERY TANK GROUP 40. . . . . . . . . . . . . . .
CONTROL CONSOLE GROUP 42. . . . . . . . . . .
LEVER GROUP 44. . . . . . . . . . . . . . . . . . . . . . . . .
NON-DRIVE MODEL WHEEL GROUP 46. . . . .
BRUSH DRIVE GROUP 48. . . . . . . . . . . . . . . . . .
SKIRT GROUP 50. . . . . . . . . . . . . . . . . . . . . . . . . .
CURVED SQUEEGEE GROUP 52. . . . . . . . . . .
OPTIONS 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EStKIT 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SQUEEGEE WAND ASSEMBLY 56. . . . . . . . . .
BRUSH WEIGHT KIT 57. . . . . . . . . . . . . . . . . . . .

OPERATION
Speed Scrubt2001 Battery (11–99) 3
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
suited to scrub floors in an indoor environment and is
not constructed for any other use. Use only
recommended pads, brushes and cleaning detergents.
The following safety alert symbols are used throughout
this manual as indicated in their description.
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signals potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
–Unless trained and authorized.
–Unless operation manual is read and
understood.
–In flammable or explosive areas unless
designed for use in those areas.
2. Before starting machine:
–Make sure all safety devices are in place
and operate properly.
3. When using machine:
–Go slow on inclines and slippery surfaces.
–Use care when reversing machine.
–Always follow safety and traffic rules.
–Report machine damage or faulty
operation immediately.
–Follow mixing and handling instructions
on chemical containers.
4. Before leaving or servicing machine:
–Stop on level surface.
–Turn off machine.
5. When servicing machine:
–Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
–Block machine tires before jacking
machine up.
–Use hoist or jack of adequate capacity to
lift machine.
–Disconnect battery connections before
working on machine.
–Wear protective gloves when handling
batteries or battery cables.
–Avoid contact with battery acid.
–Use manufacturer supplied or approved
replacement parts.
WARNING: Batteries emit hydrogen gas.
Explosion or fire can result. Keep sparks and
open flame away. Keep battery compartment open
when charging.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
WARNING: Flammable materials or reactive
metals can cause explosion or fire. Do not pick
up.

OPERATION
4SpeedScrubt2001 Battery (11–01)
MACHINE COMPONENTS
2
3
5
8
14
1
67
12
10 9
13
11
15
20
16
14
7
19
22 21
17
6
18
4
1. Control Grips
2. Vacuum ON/OFF Switch
3. Brush ON/OFF Switch
4. Battery Meter
5. Brush Circuit Breaker
6. Squeegee Lift Lever
7. Solution Flow Lever
8. Solution Flow Adjustment Knob
9. Adjustable Control Console Levers
10. Brush Lift Lever
11. Brush Lift Foot Lever
12. Recovery Tank Drain Hose
13. Solution Tank Drain Hose
14. Squeegee Assembly
15. Control Console
16. Recovery Tank
17. Recovery Tank Lid
18. Solution Fill Door
19. Safety Lights
20. Rear Drive Wheel
21. Scrub Head
22. Scrub Head Skirt

OPERATION
SpeedScrubt2001 Battery (11–99) 5
MACHINE INSTALLATION
UNCRATING MACHINE
Carefully check carton for signs of damage. Report
damages at once to carrier. Check carton contents to
ensure all accessories are included.
To uncrate your machine, remove straps and raise
brush head. To raise brush head, step down firmly on
the bottom brush lift foot pedal until pedal locks into
the raised position. Carefully lift or create a ramp using
crate boards to remove machine from pallet.
ATTENTION: Do not roll machine off pallet,
damage may occur.
ATTENTION: To prevent possible machine
damage, install batteries after removing machine
from shipping pallet.
INSTALLING BATTERIES
WARNING: Batteries emit hydrogen gas.
Explosion or fire can result. Keep sparks and
open flame away. Keep battery compartment open
when charging.
FOR SAFETY: When servicing machine, wear
protective glove when handling batteries or
battery cables. Avoid contact with battery acid.
Recommended Battery Specifications:
Two 12 volt, deep cycle, 130 amp hour batteries.
Maximum battery dimensions are 180mm (7.13 in) W
x 330mm (13 in) L x 254mm (10 in) H.
1. Turn all switches to the off position.
2. Carefully hinge open recovery tank to access
battery compartment. Make sure recovery tank is
empty before opening. Remove loose battery
cable and PVC battery spacer from compartment
(Figure 1).
FIG. 1
3. Carefully install batteries into compartment and
arrange battery posts as shown (Figure 2).
FIG. 2
ATTENTION: Do not drop batteries into
compartment! Battery and machine housing
damage may result.
4. To secure batteries, place white PVC tube spacer
‘‘A”behind batteries in compartment (Figure 2).
5. Connect cables to battery posts in numerical order
as labeled (RED to POSITIVE and BLACK to
NEGATIVE) (Figure 2).
6. Apply a light coating of non–metallic grease or
protective spray on the cable connections to
prevent battery corrosion.

OPERATION
6SpeedScrubt2001 Battery (11–01)
MACHINE SETUP
PRE–OPERATION CHECKS
1. Sweep and dust mop floor.
2. Check battery meter charge level to ensure
batteries are fully charged (See BATTERY
CHARGING).
3. Check that a pad/brush is installed.
4. Check that squeegee is installed.
ATTACHING SQUEEGEE
1. Pull back on squeegee lift lever to raise squeegee
mount bracket.
2. Loosen two thumb knobs on squeegee and slide
squeegee into slot at rear of squeegee mount
bracket. Make sure that squeegee roller wheels
are facing toward the rear (Figure 3).
FIG. 3
3. Tighten thumb knobs securely.
INSTALLING BRUSH OR PAD DRIVER
1. Turn machine off.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface and turn off
machine.
2. Lower brush head. Step down firmly on top pedal
and push pedal forward to lower (Figure 4).
FIG. 4
3. Position squeegee swivel mechanism so it’s
centered behind machine.
4. Tilt machine back to access motor hub.
ATTENTION: Do not leave machine tilted back for
an extended time. Battery acid may leak.
5. Select a recommended pad or brush that best
meets your cleaning needs.
NOTE: Consult your authorized distributor for pad and
brush recommendations.
6. (For Pad Installation) Attach pad to pad driver
before installing driver to motor hub. To attach
pad, remove plastic centerlock from pad driver
and position pad centered on driver, replace
centerlock securely (Figure 5).
FIG. 5
7. Attach brush/pad driver to motor hub. Align 3
mounting studs with slots in motor hub and give
the driver a quick turn toward the spring clip on the
motor hub to attach brush/pad driver. Be certain
that spring clip locks into one of the studs on the
driver before operating machine (Figure 6).

OPERATION
SpeedScrubt2001 Battery (11–01) 7
FIG. 6
8. Raise brush head. To raise brush head, step down
firmly on the bottom brush lift foot pedal until brush
locks into the raised position (Figure 7).
FIG. 7
FILLING SOLUTION TANK
1. Push machine to fill station. Raise squeegee and
brush head when transporting.
2. Pull solution flow lever completely back to shut off
solution flow (Figure 8).
FIG. 8
3. Open solution fill door at front of machine and fill
solution tank with 38L (10 gal) of clean water,
60°C (140°F) maximum temperature. Or use the
rear fill port to fill solution tank. The clear tube
below the fill port has 19L (5 gal) increment
markers to indicate amount of water in tank
(Figure 9).
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
FIG. 9
NOTE: If filling with a bucket be certain that bucket is
clean. This will prevent the chance of clogging the
solution lines.
4. Add cleaning detergent according to mixing
instructions on bottle.
FOR SAFETY: When using machine, follow
mixing and handling instructions on chemical
containers.
ATTENTION: Use only recommended cleaning
detergents, DO NOT use substitutes. Consult an
authorized distributor for cleaning detergent
recommendations.

OPERATION
8SpeedScrubt2001 Battery (11–01)
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
1. Adjust control grips to a comfortable operating
height (three settings). Squeeze together two
levers under console to raise or lower control grips
(Figure 10).
FIG. 10
2. Lower squeegee by releasing squeegee lift lever
from the lock position (Figure 11).
FIG. 11
3. Lower brush head, step down firmly on top brush
lift pedal and push pedal forward to lower
(Figure 12).
FIG. 12
4. Turn vacuum switch to the on position.
5. Push solution flow lever forward to desired flow
rate. Solution will immediately begin to flow once
lever is activated (Figure 13).
FIG. 13
To adjust the maximum solution flow rate, turn
solution flow adjustment knob down to increase or
up to decrease (Figure 14).
FIG. 14

OPERATION
SpeedScrubt2001 Battery (06–99) 9
6. Turn brush switch to the on position.
ATTENTION: To prevent floor finish damage, DO
NOT leave machine at stand still once brush
begins to spin.
7. Begin scrubbing by pushing machine forward.
WHILE OPERATING MACHINE
WARNING: Flammable materials or reactive
metals can cause explosion or fire. Do not pick
up.
1. Periodically check for excessive foam in recovery
tank (look through clear lid). If excessive foam
appears, pour a foam control solution into the
recovery tank.
ATTENTION: Do not allow foam or water to enter
the float shut-off screen, vacuum motor damage
will result. Foam will not activate float shut-off
screen.
2. If more scrubbing pressure is needed for small
heavily soiled areas, simply pull brush lift lever
upward while operating (Figure 15).
FIG. 15
3. If squeegee leaves streaks, raise squeegee and
wipe both blades with a cloth.
4. Before stopping or turning machine around, pull
back on solution control lever to shut off solution
flow.
5. View clear tube at rear of machine for remaining
cleaning solution.
6. Periodically check battery meter’s discharge level.
When needle drops to the red zone, recharge
batteries.
ATTENTION: Do not continue to run machine when
battery meter needle is in the red zone, battery
damage will result.
7. When the solution tank runs dry, turn off brush
switch, shut off solution control lever and continue
to vacuum until all dirty water is consumed into the
recovery tank. Raise the squeegee and brush
head and drain recovery tank (See DRAINING
TANKS).
BRUSH MOTOR CIRCUIT BREAKER
Machine is equipped with a circuit breaker to protect
brush motor from damage. If the brush motor circuit
breaker trips, it can not be reset immediately.
Determine reason why breaker tripped, allow motor to
cool and then reset. Circuit breaker will trip due to
brush motor overload. Clean or change pad if breaker
should trip. Brush motor circuit breaker button is
located at rear of control console

OPERATION
10 SpeedScrubt2001 Battery (06–99)
DRAINING TANKS
1. Turn machine off.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface and turn off
machine.
2. Raise squeegee and brush head and transport
machine to floor drain.
NOTE: If using bucket to drain machine, do not use
same bucket for filling solution tank.
DRAINING RECOVERY TANK
When finished scrubbing or when refilling solution
tank, recovery tank should be drained and cleaned.
ATTENTION: If recovery tank is not drained before
refilling, foam or water may enter the float shut-off
screen and damage vacuum motor. Foam will not
activate float shut–off screen.
1. Remove drain hose from holder, position hose
over floor drain and twist off drain hose plug. To
completely drain recovery tank, hinge open tank
and flip up tank support stand to rest tank on
(Figure 16).
FIG. 16
2. Clean recovery tank after each use. Use a hose to
rinse out recovery tank. Be careful not to spray
water into float shut-off screen.
3. Replace drain hose plug tightly after draining.
DRAINING SOLUTION TANK
To drain leftover cleaning solution from solution tank
perform the following steps:
1. Pull clear tube off hose barb at rear of machine
and drain solution into floor drain or bucket
(Figure 17).
FIG. 17
2. Rinse solution tank with clean water after each
use. This will prevent clogging due to chemical
buildup.
3. Push solution flow lever forward to rinse out
solution flow system.
4. Reconnect clear tube. Be certain tube is
completely pushed on hose barb.

OPERATION
SpeedScrubt2001 Battery (11–01) 11
BATTERY CHARGING
NOTE: Recharge batteries ONLY after a total of 30
minutes of use or more. This will prolong battery life.
The following charging instructions are intended
for chargers supplied with machine. Only use a
charger with the following specifications to
prevent battery damage.
CHARGER SPECIFICATIONS:
SOUTPUT VOLTAGE - 24 VOLTS
SOUTPUT CURRENT - 10 TO 20 AMPS MAXIMUM
SAUTOMATIC SHUTOFF CIRCUIT
SFOR DEEP CYCLE BATTERY CHARGING
NOTE: For optimum machine operation, keep
batteries charged at all times. Never let batteries set in
a discharge condition.
FOR SAFETY: When servicing machine, wear
protective gloves when handling batteries and
battery cables. Avoid contact with battery acid.
1. Push machine to a well–ventilated area for
charging.
2. Turn machine off.
3. Hinge open recovery tank to access batteries.
Make sure recovery tank is empty before opening
(Figure 18).
FIG. 18
WARNING: Batteries emit hydrogen gas.
Explosion or fire can result. Keep sparks and
open flame away. Keep battery compartment open
when charging.
4. Check fluid level (A) in each battery cell. Do not
charge batteries unless fluid is slightly covering
battery plates (B). If needed, add just enough
distilled water to slightly cover plates. DO NOT
overfill. Batteries can overflow during charging due
to expansion. Replace cell caps before charging
(Figure 19).
A
B
FIG. 19
5. Plug charger DC output connector to battery
connector located near battery compartment. Flip
up tank support stand and rest tank on stand
(Figure 20).
FIG. 20
NOTE: Once charger is connected to machine, the
machine becomes inoperable.
6. Plug charger power supply cord into a grounded
wall outlet (Figure 21).
Grounded
3 Hole Outlet
Ground Pin
FIG. 21
7. Charger will automatically begin charging and
automatically shut off when fully charged.
8. When disconnecting charger, always unplug
charger from wall outlet first.
9. Recheck battery fluid level after charging. If
needed, add distilled water to bring level to bottom
of sight tubes. Be certain to replace cell caps
securely and to wipe off the top of batteries with a
clean cloth.

OPERATION
12 SpeedScrubt2001 Battery (11–99)
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow machines daily, weekly and monthly
maintenance procedures.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface and turn off
machine.
FOR SAFETY: When servicing machine,
disconnect battery connections before working on
machine.
ATTENTION: Contact an Authorized Service
Center for machine repairs. Machine repairs
performed by other than an authorized person will
void your warranty.
DAILY MAINTENANCE
(Every 4 Hours of Use)
1. Remove and clean pad/brush.
2. Remove and clean float shut-off screen located in
recovery tank (Figure 22).
FIG. 22
3. Drain and rinse tanks thoroughly. After draining
tanks, hinge recovery tank until you can see
vacuum intake hole at rear of tank. Remove any
debris in hole if necessary.
4. Raise squeegee and wipe it down with a dry cloth.
Store squeegee in the up position to prevent
squeegee damage.
5. Clean machine with an all purpose cleaner and
damp cloth.
ATTENTION: Do not power spray or hose off
machine. Electrical component damage may
result.
6. Recharge batteries.
WEEKLY MAINTENANCE
(Every 20 Hours of Use)
1. Check fluid level in battery cells.
2. Clean battery tops from corrosion.
3.Check for loose or corroded battery cables.
MONTHLY MAINTENANCE
(Every 80 Hours of Use)
1. Flush solution system. Pour 11.3 liters (3 gal) of
hot water, 60_C (140_F) maximum temperature,
into solution tank. Add an alkaline detergent
according to mixing instructions. Over a floor
drain, operate machine for 30 seconds. Turn
machine off and leave overnight. Next day,
disperse solution and rinse solution system.
FOR SAFETY: When using machine, follow
mixing and handling instructions on chemical
containers.
2. Lubricate all linkage pivot points with silicon spray
then coat with a water resistant grease to maintain
a smooth operation.
3. Check machine for water leaks and loose nuts and
bolts.
QUARTERLY MAINTENANCE
(Every 250 Hours of Use)
Check vacuum and brush motor for carbon brush
wear, replace brushes when worn to a length of 10mm
(0.38 in) or less.
Contact an Authorized Service Center for motor
maintenance.
BATTERY MAINTENANCE
WARNING: Batteries emit hydrogen gas.
Explosion or fire can result. Keep sparks and
open flame away. Keep battery compartment open
when charging.
FOR SAFETY: When servicing machine, wear
protective gloves when handling batteries and
battery cables. Avoid contact with battery acid.
1. Always follow proper charging instructions (See
BATTERY CHARGING).
2. After charging, check fluid level in each battery
cell. The level (A) should reach bottom of sight
tubes (B). If needed, add just enough distilled
water to reach bottom of sight tubes. DO NOT
overfill (Figure 23).

OPERATION
SpeedScrubt2001 Battery (11–01) 13
A
B
FIG. 23
3. Keep battery tops and terminals clean and dry.
To clean batteries:
a. Mix a strong solution of baking soda and
water.
b. Brush solution sparingly over battery tops,
terminal and cable connectors.
NOTE: Do not allow baking soda solution to enter
battery cells.
c. Use wire brush to clean terminal post and
cable connections.
d. After cleaning, apply a coating of clear battery
post protectant to terminals and cable
connections.
4. Check for loose or worn cables. Replace if worn.
TRANSPORTING MACHINE
When transporting machine by use of trailer or truck,
be certain to follow tie–down procedures below:
FOR SAFETY: When using machine, go slow on
inclines and slippery surfaces.
1. Remove squeegee from machine and raise scrub
head. Leave pad or brush installed.
2. Load machine using a recommended loading
ramp.
3. Position front of machine up against front of trailer
of truck. Once machine is positioned, lower brush
head.
4. Place a block behind the drive wheel and the rear
casters.
5. Place tie–down straps over top of machine and
secure straps to floor. It may be necessary to
install tie–down brackets to the floor of your trailer
or truck.
STORING MACHINE
Store machine in a dry area in the upright position.
Before storing machine be certain to flush tanks and
drain machine of all water. Remove recovery tank lid
to promote air circulation. Raise pad driver and
squeegee off floor to prevent damage.
ATTENTION If storing machine in freezing
temperatures, be certain to drain machine of all
water. Damage due to freezing temperatures is not
covered by warranty.
ATTENTION: Do not expose machine to rain; store
indoors.
RECOMMENDED STOCK ITEMS
Refer to Parts List section for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description. See example below:

OPERATION
14 SpeedScrubt2001 Battery (06–99)
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
No power. Batteries need charging. See Battery Charging.
Battery(s) faulty. Replace battery(s)
Loose battery cable. Tighten loose cables.
Batteries are not connected
correctly. See Battery Installation.
Brush motor does not run. Faulty brush switch. Contact Service Center.
Machine circuit breaker has tripped. Clean or replace pad or brush and
reset breaker button.
Rectifier has burned out. Contact Service Center.
Faulty wiring. Contact Service Center.
Faulty brush motor. Contact Service Center.
Carbon brushes worn. Contact Service Center.
Faulty solenoid. Contact Service Center.
Vacuum motor does not run. Faulty vacuum switch or wiring. Contact Service Center.
Faulty vacuum motor. Contact Service Center.
Carbon brushes worn. Contact Service Center.
Short run time. Batteries not fully charged. Charge batteries.
(Run time 2.47 hours on full charge) Bad cell in one or more batteries. Replace battery.
(Run time 2.47 hours on full charge)
Batteries need maintenance. See Battery Maintenance.
Faulty charger. Replace charger.
Safety lights do not work. Flasher is burned out. Contact Service Center.
Little or no solution flow. Solution flow lever is not activated. Push solution flow lever forward.
Solution line is clogged. Remove hose and blow
compressed air through it.
Solution valve is clogged. Remove valve and clean. Do not
scratch or damage inside of valve.
Solution flow adjustment knob
needs adjusting. Adjust solution flow knob to increase solution flow. Turn knob
down to increase flow.

OPERATION
SpeedScrubt2001 Battery (06–99) 15
TROUBLE SHOOTING –CONTINUED
PROBLEM CAUSE SOLUTION
Poor water pick up. Recovery tank is full. Empty recovery tank.
Ball float shutoff screen inside
recovery tank is clogged. Remove screen and clean.
Squeegee is clogged with debris. Clean squeegee.
Squeegee blades are worn. Replace squeegee blades.
Squeegee thumbscrews are loose. Tighten thumbscrews.
Vacuum hose connections are
loose or hose has a hole. Push vacuum hose cuffs firmly on connections. Replace hose if
damaged.
Vacuum hose is clogged with
debris. Remove clogged debris.
Tank gasket is defective. Replace tank gasket.
Recovery tank water inlet is
plugged. Inlet is located at bottom
of recovery tank.
Empty recovery tank and tilt it
sideways to locate inlet hole,
remove clogged debris.
Drain hose plug is loose. Tighten drain plug.
Clear recovery tank lid is loose. Tighten lid.
Vacuum motor is loose. Tighten down vacuum motor. Do
not over tighten and damage motor.
Battery charge is low. Charge batteries. Do not run
machine when battery meter is in
the red zone.

OPERATION
16 SpeedScrubt2001 Battery (06–99)
SPECIFICATIONS
LENGTH 1194 mm (47 in)
WIDTH 559 mm (22 in)
HEIGHT 965 mm (38 in)
WEIGHT 146 Kg (315 lb)
SOLUTION TANK CAPACITY 38 L (10 gal)
RECOVERY TANK CAPACITY 45 L (12 gal)
CLEANING PATH WIDTH 508 mm (20 in)
BRUSH MOTOR .75hp, 220 rpm, 24v, 20A, 560w
VACUUM MOTOR .5hp, 2 stage, 353w, 14A, 24v
WATER LIFT 1118 mm (44 in)
BATTERIES 2–130A/hr, 12v deep cycle
RUN TIME on full charge 2.47 hours
DECIBEL RATING AT OPERATOR’S EAR, INDOORS ON TILE 70dB(A)

OPERACIÓN
Speed Scrubt2001 Batería (11–01) 17
Este manual acompaña a todos los modelos estándar
nuevos. En él se indican las instrucciones necesarias
para la utilización y el mantenimiento de la máquina.
Lea el manual entero para comprender el
funcionamiento de la máquina antes de utilizarla o
revisarla.
Esta máquina le proporcionaráun servicio excelente.
Sin embargo, obtendrálos mejores resultados al coste
mínimo si:
SUtiliza la máquina con un cuidado razonable.
SRevisa la máquina periódicamente - según las
instrucciones de mantenimiento adjuntas.
SLa máquina recibe mantenimiento con las piezas de
repuesto del fabricante o equivalentes.
DATOS DE LA MÁQUINA
ModeloNo.:
Fecha de preparación:
No. de serie:
Sírvase llenar los datos en el momento de la preparación
para referencia en el futuro.
ÍNDICE
MEDIDAS DE SEGURIDAD 18. . . . . . . . . . . . . . . . . .
COMPONENTES DE LA MÁQUINA 19. . . . . . . . . . .
INSTALACIÓN DE LA MÁQUINA 20. . . . . . . . . . . . .
DESEMBALADO DE LA MÁQUINA 20. . . . . . . .
INSTALACIÓN DE LA BATERÍA20. . . . . . . . . . .
PREPARACIÓN DE LA MÁQUINA 21. . . . . . . . . . . .
COMPROBACIONES PREVIAS A LA PUESTA
EN FUNCIONAMIENTO 21. . . . . . . . . . . . . . . . . .
FIJACIÓN DE LA ESCOBILLA DE GOMA 21. .
INSTALACIÓN DEL IMPULSOR DEL CEPILLO
O DE LA ALMOHADILLA 21. . . . . . . . . . . . . . . . .
LLENADO DEL DEPÓSITO DE LA
DISOLUCIÓN22. . . . . . . . . . . . . . . . . . . . . . . . . . .
FUNCIONAMIENTO DE LA MÁQUINA 23. . . . . . . .
DURANTE LA UTILIZACIÓN DE LA
MÁQUINA 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CORTACIRCUITOS DEL MOTOR DE LA
ALMOHADILLA 24. . . . . . . . . . . . . . . . . . . . . . . . .
VACIADO DE LOS DEPÓSITOS 24. . . . . . . . . . . . . .
VACIADO DEL DEPÓSITO DE
RECUPERACIÓN24. . . . . . . . . . . . . . . . . . . . . . .
VACIADO DEL DEPÓSITO DE
LA DISOLUCIÓN25. . . . . . . . . . . . . . . . . . . . . . . .
CARGA DE LAS BATERÍAS 25. . . . . . . . . . . . . . . . .
MANTENIMIENTO DE LA MÁQUINA 27. . . . . . . . .
MANTENIMIENTO DIARIO 27. . . . . . . . . . . . . . .
MANTENIMIENTO SEMANAL 27. . . . . . . . . . . . .
MANTENIMIENTO MENSUAL 27. . . . . . . . . . . .
MANTENIMIENTO TRIMESTRAL 27. . . . . . . . .
MANTENIMIENTO DE LA BATERÍA27. . . . . . .
TRANSPORTE DE LA MÁQUINA 28. . . . . . . . . . . . .
ALMACENAMIENTO DE LA MÁQUINA 28. . . . . . .
RECOMENDACIONES PARA EL
ALMACENAMIENTO 28. . . . . . . . . . . . . . . . . . . . . . . .
LOCALIZACIÓN DE AVERÍAS 29. . . . . . . . . . . . . . .
ESPECIFICACIONES 31. . . . . . . . . . . . . . . . . . . . . . .
DIAGRAMAS ELECTRICAS 32. . . . . . . . . . . . . . . . .
LISTA DE PIEZAS 34. . . . . . . . . . . . . . . . . . . . . . . . . . .
CEPILLO DEL REEMPLAZO Y GRUPO DEL
MANDO DE LA ALMOHADILLA 34. . . . . . . . . . .
GRUPE DEL DEPÓSITO DE DISOLUCIÓN36.
CONJUNTO PANEL TRASERA 38. . . . . . . . . . .
CONJUNTO DESPÓSITO RECUPERAR 40. . .
CONJUNTO CONSOLA DE CONTROLES 42. .
CONJUNTO DE PALANCAS 44. . . . . . . . . . . . . .
CONJUNTO PARA LEVANTAR CEPILLO 46. . .
CONJUNTO IMPULSO DE CEPILLO 48. . . . . .
CONJUNTO JUEGO 50. . . . . . . . . . . . . . . . . . . . .
CONJUNTO PALETA ENCORUADO 52. . . . . . .
OPCIONES 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EStJUEGO 54. . . . . . . . . . . . . . . . . . . . . . . . . . . .
GROUPE D’ASPIRATION ET RACLETTE À
MAIN 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KIT DEL PESO DEL CEPILLO 57. . . . . . . . . . . .

OPERACIÓN
18 Speed Scrubt20001 Batería (11–01)
MEDIDAS DE SEGURIDAD
Esta máquina estádestinada al uso comercial. Está
diseñada para fregar suelos en recintos cerrados y no
debe utilizarse para ningún otro uso. Utilice
únicamente los cepillos, almohadillas y disoluciones
limpiadoras recomendados.
En este manual se utilizan los siguientes símbolos de
peligro, cuyo significado se indica a continuación:
ADVERTENCIA: Para advertir sobre riesgos o
hábitos peligrosos que podrían causar lesiones
corporales graves o fatales.
PARA SU SEGURIDAD: Para indicar las
operaciones que deben realizarse para una
utilización segura del equipo.
La siguiente información indica las condiciones
potencialmente peligrosas para el operario o equipo:
PARA SU SEGURIDAD:
1. No utilice la máquina:
–Salvo que estéadecuadamente cualificado
y autorizado.
–Salvo que haya leído y comprendido el
manual del operario.
–En áreas donde exista material inflamable
o explosivo salvo que estéespecialmente
diseñada para utilizarla en estas zonas.
2. Antes de arrancar la máquina:
–Asegúrese de que todos los dispositivos
de control se encuentran en su sitio y
funcionan correctamente.
3. Al utilizar la máquina:
–Conduzca despacio en pendientes y
superficies resbaladizas.
–Conduzca con cuidado al desplazarse
marcha atrás.
–Cumpla siempre las normas de tráfico y
seguridad.
–Informe inmediatamente si la máquina
presenta averías o funciona
incorrectamente.
–Siga las instrucciones de manipulación y
mezcla indicadas en los envases de los
productos químicos.
4. Antes de estacionar o revisar la máquina:
–Deténgase en una superficie plana.
–Apague la máquina.
5. Al revisar la máquina:
–Evite las partes en movimiento. No lleve
chaquetas, camisas o mangas sueltas.
–Calce las ruedas de la máquina antes de
levantarla con un gato.
–Utilice un gato o elevador con capacidad
suficiente para elevar la máquina.
–Desconecte las conexiones de la batería
antes de empezar a trabajar en la máquina.
–Protéjase las manos con guantes al
trabajar con las baterías o sus cables.
–Evite el contacto con el ácido de la batería.
–Utilice piezas de recambio suministradas o
aprobadas por el fabricante.
ADVERTENCIA: Las baterías emiten
hidrógeno gaseoso. Existe peligro de incendio o
explosión. Mantenga chispas y llamas alejadas de
la máquina. Mantenga el compartimento de la
batería abierto mientras realiza la operación de
carga.
ADVERTENCIA: Los materiales inflamables
pueden provocar explosiones o incendios. No
utilice materiales inflamables en los depósitos.
ADVERTENCIA: Los materiales inflamables o
metales reactivos pueden provocar explosiones o
incendios. No los recoja.

OPERACIÓN
SpeedScrubt2001 Batería (11–01) 19
COMPONENTES DE LA MÁQUINA
3
2
5
8
14
1
67
12
10 9
13
11
15
20
16
14
7
19
22 21
17
6
18
4
1. Mandos de control
2. Interruptor de Encendido/Apagado (ON/OFF) de
la aspiración
3. Interruptor de Encendido/Apagado (ON/OFF) del
cepillo
4. Indicador del nivel de carga de la batería
5. Cortacircuitos del cepillo.
6. Palanca de elevación de la escobilla de goma
7. Palanca del flujo de la disolución
8. Botón de ajuste del flujo de la disolución
9. Palancas de ajuste de la consola de control
10. Palanca de elevación del cepillo
11. Pedal de elevación del cepillo
12. Manguera de vaciado del depósito de
recuperación
13. Manguera de vaciado del depósito de
recuperación con indicación en galones.
14. Conjunto de la escobilla de goma
15. Consola de control
16. Depósito de recuperación
17. Tapa del depósito de recuperación
18. Puerta de relleno de la disolución
19. Luces de seguridad
20. Rueda de tracción trasera
21. Cabezal de fregado
22. Aleta del cabezal de fregado
23. Rodillos de pared

OPERACIÓN
20 SpeedScrubt20001 Batería (11–01)
INSTALACIÓN DE LA MÁQUINA
DESEMBALADO DE LA MÁQUINA
Compruebe cuidadosamente si la caja de cartón
muestra daños. En caso de que asísea informe
inmediatamente de los daños al transportista. Controle
el contenido de la caja para asegurarse que incluye
todos los accesorios.
Para desembalar la máquina retire las cintas y eleve
el cabezal de barrido. Para elevar este cabezal pise
firmemente sobre la parte inferior del pedal de
elevación del cepillo hasta que dicho pedal quede
bloqueado en la posición elevada. Levante la máquina
con cuidado o utilice una rampa formada con las
planchas de embalaje para retirar la máquina del
pallet.
ATENCIÓN: No ruede equipo de pallet. Pude
danarse.
INSTALACIÓN DE LA BATERÍA
ADVERTENCIA: Las baterías emiten gases de
hidrógeno que pueden causar explosiones o
incendios. Manténgalas alejadas de chispas y
fuego.
ADVERTENCIA: El ácido de la batería puede
causar quemaduras. Utilice guantes protectores y
protéjase los ojos al revisar las baterías.
Especificaciones de la batería:
Dos baterías de 12 voltios de ciclo de 130 amp por
hora. Pieza de numero 130869. Las dimensiones
máximas de las baterías son 180 mm x 330 mm x 254
mm (ancho x alto x largo)
1. Retire la llave del contacto.
2. Abra con cuidado el depósito de recuperación y
colóquelo lateralmente girándolo sobre la bisagra
para poder acceder al compartimento de la
batería. Extraiga del compartimento el cable
suelto de la batería y el espaciador de PVC de la
batería (Figura 1).
FIG. 1
3. Instale cuidadosamente las baterías en el
compartimento y coloque los bornes de la batería
como se indica (Figura 2).
FIG. 2
ATENCIÓN:: No deje caer las baterías en el
compartimento! Tanto la batería como su soporte
podrían averiarse. La garantía no cubre este tipo
de desperfectos.
4. Para fijar las baterías coloque el tubo espaciador
blanco ”A”de PVC en el compartimento, detrás de
las baterías, como se muestra en la Fig..
5. Conecte los cables a los bornes de la batería en el
orden numérico indicado en la etiqueta (ROJO EN
EL POSITIVO Y NEGRO EN EL NEGATIVO)
(Figura 2).
6. Vuelva a comprobar la conexión de los cables
antes de cerrar el compartimento de la batería.