Noise 01-00013B User manual

INSTRUCTIONMANUAL
AUTOMATIC ELIMINATION PROBE
MODEL 01-00013B
NOISE LABORATORY CO., LTD.
Editoin1.02
AEC00297-00E-0C

NOTICE
• The contents of this instruction manual（the “Manual”）are subject to change without
prior notice.
• No part of the Manual may be reproduced or transferred, in any form and for any
purpose, without the permission of Noise Laboratory Co., Ltd.(the “Company”)
• The contents of the Manual have been thoroughly examined. However, if you find any
problems, misprints, or missing information, please contact the dealer where you
purchased your product (the “Dealer”).
• The Company or the Dealer will not accept any responsibility for any loss or damage
resulting from improper usage, failure to follow the Manual, or any repair or modifications
of this product (the “Unit”) undertaken by a third party other than the Company or parties
authorized by the Company.
• The Company will not accept responsibility for any loss or damage resulting from
remodeling or conversion solely undertaken by the user.
• In addition, please note that the Company cannot be held responsible for any
consequences arising from the use of this product.

We thank you very much for your buying AUTOMATIC ELIMINATION PROBE MODEL 01-00013B FOR
ESS-Series. This unit is connected to ESS so as to automatically discharge EUT (Equipment under test)
that is charged by applying static electricity. It is recommended that this manual be thoroughly
understood and used as ready reference for operation.
For the safety precautions, warranty terms and so on, refer to the relevant section of the manual of
your simulator.
1. CONTENTS IN THE PACKAGE
Automatic elimination probe··················· 1 pc.
Instruction manual (this manual)············· 1 pc.
2. NAME AND FUNCTION OF EACH PART
①
①①
① UX connector: Connects to AUX CONNECTOR on the rear panel of ESS.
②
②②
② AUX connecting cable
③
③③
③ Elimination switch/lamp: The pilot lamp is on during elimination. When this switch is pressed to
set to no-elimination position (Lamp is off), manual elimination can be performed.
④
④④
④ HOT side clip (Red): Connect the cabinet/earth terminal of EUT.
⑤
⑤⑤
⑤ HOT side elimination resistance: Incorporates resistance of 470kΩ.
⑥
⑥⑥
⑥ HOT side cable (White): 30kV high-voltage cable is used.
⑦
⑦⑦
⑦ GND side clip (Black): Connects to the ground of electrostatic simulator system
⑧
⑧⑧
⑧ GND side elimination resistance: Incorporates resistance of 470kΩ.
⑨
⑨⑨
⑨ GND side cable (Black)
⑤
⑥
④
⑦
⑧
⑨
③
①
②

3. HOW TO USE
① Connect AUX connector to the AUX connector of ESS.
② Connect HOT side clip (red) to Cabinet/Earth terminal of EUT.
③ Connect GND side clip (black) to the ground of electrostatic simulator system. (Usually,
connect to the grounding plane.)
④ Turn on power to ESS and press keys →→to display the setting
screen.
⑤ Move the setting frame to the title "ELIMINATION PROBE" by means of
key.
⑥ Set the elimination probe to the intended operation mode by means of the rotary knob.
NOT USED...........Elimination probe does not work. (It is set to no-elimination status.)
Manual elimination can be performed using the elimination switch.
Discharge ＯＮ
ＯＦＦ
ＯＮ
Elimination
ＯＦＦ
EVERY DISCHARGE.........Elimination is performed at every discharge. However, when the
applying interval is set at less than one second, elimination is
performed at every count-up. (Same as COUNT UP)
ＯＮ
Discharge
ＯＦＦ
ＯＮ
Elimination
ＯＦＦ
COUNT-UP.............Elimination is performed when the specified number of times of discharge
is finished.
Discharge ＯＮ
ＯＦＦ
Elimination ＯＮ
ＯＦＦ
MENU
6 1
▽
▽▽
▽

4. SPECIFICATIONS
Items Specifications
Max. elimination voltage 30 kV
Elimination resistance 470KΩ＋470 KΩ＝940 KΩ
Hot side cable length 2 m
GND side cable length 2 m
AUT connecting cable length 2 m
Dimensions 150(D) x 85(W) x 60(H) except any projection
CAUTION
Do not connect HOT side clip and GND side clip to the wrong side. Otherwise, correct test
results may not be obtained.
Avoid disassembling the main unit and elimination resistance.
When no power to ESS is turned on or nothing is connected to AUX connector of elimination
probe, the probe is set to no-elimination status (HOT side insulated from GND side). Even if the
elimination switch is pressed in this status, elimination will not be performed.
※When using a warning light or external trigger output together with the elimination probe, contact
NOISE LABORATORY

NOISE LABORATORY CO., LTD.
1-4-4, Chiyoda, Chuo-ku, Sagamihara City, Kanagawa Pref., 252-0237, Japan
TEL: [phone] FAX: [phone]
URL: http://www.noiseken.co.jp PRINTED IN JAPAN