Nokeval 2011KCI User manual

2011KCI
2211KCI
Weighing display
User manual
18.6.2009
Firmware V2.0

INTRODUCTION
2011KCI and 2211KCI are input ards spe ially
designed for Kone ranes. They an be pla ed in
any of Nokeval E and F series large displays, like
1000F4.
The ard provides one (2011KCI) or two (2211KCI)
2-8 V analog input hannels. The upper end of
these an be s aled freely, and independently on
ea h hannel.
These models have been super eded by 2012KCI
in spring 2007.
A separate Te hni al manual is available on
request, overing more details of the KCI displays.
Table of contents
Introdu tion......................................................................................................................................................2
Ordering...........................................................................................................................................................3
Installing...........................................................................................................................................................4
Operation.........................................................................................................................................................7
User interfa e...................................................................................................................................................9
Spe ifi ations.................................................................................................................................................11
Manufacturer
Nokeval Oy
Yrittäjäkatu 12
FIN-37100 Nokia
Finland
Tel [phone]
Fax [phone]
email support@nokeval. om
WWW http://www.nokeval. om
2

ORDERING
Ordering
Obsolete
It is re ommended to repla e the 2011KCI and
2211KCI by more advan ed 2012KCI, whi h has
been available sin e spring 2007.
Order code
Example: 1000F4 – 2011KCI – 230VAC
The order ode onsists of several parts. The first
part des ribes the large display type, the next part
defines the input ard type, and the last part
sele ts the supply voltage.
Large dis lay ty e
Nokeval has four ases for large field displays.
These are:
575 Five 57 mm digits, plasti en losure
1000 Three to four 100 mm digits, steel
1100 Five to six 100 mm digits, steel
1800 Three to five 180 mm digits, steel
The letter after the ase size is either E or F. This
tells the type of the internal ele troni s. They are
prin ipally the same but have different looks. The
main differen e is that the input ard is upside
down in the E hassis. Sin e beginning of year
2003 all displays have been with F hassis.
The number after the letter defines the number of
display digits.
In ut card ty e
These large displays use Nokeval 2000 series
input ards. Custom input ards 2011KCI and
2211KCI have been designed for KCI.
Power su ly o tions
Before summer 2009, the large field displays have
been available with three power supply options:
Name Voltages
-24VDC 24 VDC
-48VAC 48 VDC or VAC
-230VAC 115 or 230 VDC or VAC
After summer 2009, the input voltage range of the
230 VAC model has been extended to over the
range 41...265 VDC/AC, removing the need for a
separate 48 VAC model. The voltage options are:
Name Voltages
-24VDC 24 VDC
-48/230VAC 48, 115, or 230 VDC or VAC
Common models
1000F4-2011KCI-48/230VAC: four 100mm digits,
1 input, power 48 to 230 VAC.
1000F4-2211KCI-48/230VAC: four digits, 2 inputs,
power 48 to 230 VAC.
S are arts ordering
Spare input ard:
2011KCI-IN
2211KCI-IN
Spare ele troni s unit in luding input ard:
SP-EL2011KCI-48/230VAC (or whi hever
supply and ards)
Spare ribbon able from el unit to large digits:
SP-CA-EL1000F
Spare large digit:
SP-100DISP (100 mm digit)
3

INSTALLING
Mounting
Dimensions for 1000F, 1100F, and 1800F:
O ening the case
To a ess the ele tri al onne tions and the small user interfa e used for onfiguring the unit, the steel ase
has to be opened. First uns rew all the s rews surrounding the display, then lift off the bla k steel frame and
the red plexiglass. Finally uns rew the s rew that is lo ated on the right hand side of the rightmost digit. Now
the display assembly may be turned away on its hinges.
Inside the main case
The electronics unit
The ele troni s unit may be opened or deta hed from the ase. To open it, uns rew the four M3 s rews that
are holding the over on its orners. If the unit has to be deta hed, uns rew the other s rews on its top and
bottom sides. Normally there is no need to open the ele troni s unit. Caution! O ening the electronics
unit ex oses arts carrying lethal voltages on units owered with more than 24 V su ly!
4
455, 625, 1025
500, 670 1045
188,250, 375
147, 210, 330
482, 650, 1030
120,130,
210

Su ly voltage and earthing
24VDC models
Bring the supply voltage to the onne tor indi ated in the pi ture. If the supply voltage is more than 24 V, the
en losure must be reliably earthed using the M4 s rew provided. A pre-fuse is not ne essary, but if one is
used, it should be at least 2 AT.
48/230VAC models
Bring the Live and Neutral wires to the ele troni s unit as in pi ture. A pre-fuse is not ne essary, but if one is
used, it should be at least 1 AT.
Conne t the Prote tive Earth wire to the M4 s rew using the Faston onne tor provided - a Faston rimping
tool is needed.
For ele tri al safety, the power and signal wires must be fastened using able ties or equivalent so that if one
signal wire is deta hed, it an not tou h any of the power supply wires, or vi e versa.
5
0.0
Slot A
Slot B
Slot C
Pow er
Ele troni s unit
Main ase
N
L
Power supply
48, 115, or 230
VAC
Earthing
0.0
Slot A
Slot B
Slot C
Power
Ele troni s unit
Main ase
Ribbon able to the digits Two able glands
9
8
7
Power supply
24 VDC.
Any polarity.
Small display + buttons
Earthing