Nokia G-240WZ-A User manual

1
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
Nokia Smart Home
7368 GPON ONT - G-240WZ-A
User Man al

2
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
Table of Contents
1.0 Introduction.....................................................................................................................................................4
2.0 ONT Software Installation/Upgrade................................................................................................................5
2.1 Procedure to upgrade RG image ................................................................................................................5
2.2 Procedure to upgrade IOT image ...............................................................................................................5
3.0 Nokia Smart Home Mobile App ......................................................................................................................6
3.1 Login to Mobile pp....................................................................................................................................6
3.2 Dashboard ...................................................................................................................................................6
3.3 Non-preferred Devices................................................................................................................................7
3.4 Unknown Devices ........................................................................................................................................7
3.5 Managing Rooms .........................................................................................................................................8
3.6 Managing Devices........................................................................................................................................8
4.0 Managing your Z-Wave Devices: ...................................................................................................................9
4.1 dding Z-Wave devices: .............................................................................................................................9
4.2 Removing a Z-Wave devices:.....................................................................................................................9
5.0 Controlling Z-Wave Devices:....................................................................................................................... 10
5.1 Controlling On/Off Plug: ......................................................................................................................... 10
5.2 Controlling Dimmer: ................................................................................................................................ 10
5.3 Controlling Lamp Mount: ......................................................................................................................... 10
5.4 Controlling Door Lock:............................................................................................................................. 10
5.5 Controlling Siren:..................................................................................................................................... 11
5.6 Smoke Detector:...................................................................................................................................... 11
5.7 Motion Detector: ..................................................................................................................................... 11
5.8 Thermostat set point ............................................................................................................................... 11
5.9 Multi-Sensor value ................................................................................................................................... 11
5.10 Door Sensor .............................................................................................................................................. 12
5.11 Plug Meter................................................................................................................................................ 12
5.12 Fan Switch ............................................................................................................................................... 12

3
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
5.13 Power Strip .............................................................................................................................................. 12
5.14 Irrigation Controller................................................................................................................................. 13
6.0 Device Automation....................................................................................................................................... 14
6.1 Managing Rules ........................................................................................................................................ 14
6.2 Managing Schedules ................................................................................................................................. 14
7.0 Troubleshooting Guidelines:........................................................................................................................ 15
7.1 Factory Default........................................................................................................................................ 15
Appendix – A: Preferred device list......................................................................................................................... 16
NOKI SM RT HOME ONT G-240WZ- Supported Z-Wave EU Frequency Devices............................................... 17
NOKI SM RT HOME ONT G-240WZ- Supported Z-Wave US Frequency Devices............................................... 18
Appendix – B: Technical Specification.................................................................................................................... 19
Z-Wave Technical information ............................................................................................................................ 19
Implemented Z-Wave device class ............................................................... 19
Supported Command Class ......................................................................... 19
Controlled Command Class ........................................................................ 21
ssociation Group Info ............................................................................. 22
Z-Wave Technical and Manufacturer details .................................................... 22
GLOSSARY ............................................................................................................................................................ 24

4
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
1.0 Introduction
This manual provides information about managing IOT features in Nokia 7368 Smart Home Product
Line ONT G-240WZ- .
The Nokia 7368 Smart Home Product Line ONT G-240WZ- is a security enabled Z-Wave plus
product that can use encrypted message to communicate with other security-enabled Z-Wave
product, such as the Z-Wave door lock.
The Nokia 7368 Smart Home Product Line ONT G-240WZ- is designed to primarily used as a Central
Static Controller (CSC) in a Z-Wave network.
The Nokia Smart Home controller allows the management of Z-Wave network and Z-Wave devices in
the network and additionally provides high level Home utomation functionality.
The Nokia Smart Home controller functionality can be accessed via the WebGUI, which can be
opened in a browser on a PC, or via ndroid/iOS Mobile pplication
Instructions for downloading and installing the Nokia Smart Home pp are mentioned in Chapter 3.
For a list of supported smart devices (Z–Wave), see the Appendix - A.

5
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
2.0 O T Software Installation/Upgrade
The Nokia 7368 Smart Home Product Line ONT G-240WZ- installation/upgrade involves a twostep
process. The first step is to perform a RG (Residential Gateway) upgrade and then second step is to
perform an IOT upgrade. Procedure is identical for first time installation and further software
upgrades.
2.1 Procedure to upgrade RG image
1. Connect Ethernet port of Laptop/PC to L N/Ethernet port 1 of ONT (L N port located on the
rear side of ONT)
2. Open any web browser e.g., Firefox, chrome or Internet explorer in the laptop and connect to
web interface of the gateway
3. Enter username and password provided by the operator in the login window.
4. Under “Maintenance” tab select firmware upgrade option.
5. Click browse button and select the RG SW file 3FE54890xxxxxx
6. Click upgrade button.
7. Click OK button for all pop-up.
8. fter RG upgrade is completed, open the RG WebGUI as indicated in steps 1 to 3
9. Click the status tab and check whether running SW version is changed to latest one.
2.2 Procedure to upgrade IOT image
1. Connect Ethernet port of Laptop/PC to L N/Ethernet port 1 of ONT (L N port located on the
rear side of ONT)
2. Open any web browser e.g., Firefox, chrome or Internet explorer in the laptop and connect to
web interface of the gateway
3. Enter username and password provided by the operator in the login window.
4. Make sure that IOT SW status is Active and Z-Wave and ZigBee interface status as online, as
shown in the below screen
5. Under “SmartHome” tab select Maintenance >Firmware Upgrade option.
6. Click Browse button and select the RG SW file 3FE546043xxxxxx
7. Click Upgrade button.
8. Click “OK” button for all pop-up windows
9. Once IOT upgrade is completed, repeat steps 1 to 3 to connect to RG web GUI
10. Check Latest S/W version under “SmartHome>Status page
11. Under SmartHome>Status page IOT SW status should be ctive, Z-Wave & ZigBee interface
should be online once upgrade is done .

6
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
3.0 okia Smart Home Mobile App
Nokia smart home solution offers Nokia Smart Home Mobile App ( ndroid and iOS) to manage the smart
devices remotely, will be available in Google Play Store & Apple Store
3.1 Login to Mobile App
To login into mobile pp follow below process:
1. Connect your smartphone to the Wi-Fi interface of the ONT.
2. Open the Nokia Smart Home pp.
3. Enter username and password provided by the operator in the login window.
3.2 Das board
When user logged in to the app, the Dashboard screen appears. On first time logging, dashboard
screen will be empty as shown below. ( s no devices are paired)
When user starts pairing the preferred devices ( Appendix – A), it gets listed in the “ ll devices”
section of the dashboard as shown below.

7
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
3.3 Non-preferred Devices
In case of non-preferred devices, it will be listed in the “ ll Devices” section, but with unsupported
text in the displayed icon. Non-preferred device will support minimal control functionality only as
specified in the Z-Wave specification document. Non-preferred devices cannot be added to any rooms
and cannot be part of automation. n alert also will be pop-up in the mobile pp when a non-
preferred device is paired to the Z-Wave network.
3.4 Unknown Devices
In case of unknown devices, it will be listed under “Unknown” sections (separate unsupported room
will be created automatically and unknown device gets populated in that room). Unknown device will
support basic functionality only. Unknown devices cannot be added to any rooms and cannot be part
of automation.

8
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
3.5 Managing Rooms
From the Smart Home screen, user can add rooms and organize smart devices by assigning them to the
rooms they are located in. Unsupported devices will be listed under unsupported room by default.
Adding a Room
1. To add a room, click on the Room icon at the bottom of the page.
2. Click on + icon at the top of the screen to add a new room. Please enter the room name under
“Enter Room Name” section. Under Choose device label – user can choose device which he
wants to assign to different rooms, more devices can be selected by scrolling left.
3. New room will be listed on the Rooms Management screen. User can delete a room by clicking
on the Trash Can icon.
3.6 Managing Devices

9
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
Once a device is paired (refer to the Pairing section below), it is automatically categorized as an
Unassigned or Unsupported device and is displayed on the Smart Home screen.
Unassigned Devices
Devices supported by the Nokia Smart Home Solution (See the Appendix - A for a list of supported
devices) are listed under this category and can be assigned to any one the created rooms.
Unknown Devices
Devices not recommended by Nokia Smart Home Solution will be listed under this category, Devices
may or may not work normally and cannot be assigned to any of the created rooms. They will be
automatically reflected under Unknown Room after pairing.
Clicking on any device will pop up a Device Information Screen providing its ame, Hardware Vendor,
Hardware Version and the Room where it is operating. You can edit the ame of a device, assign it
to a different room or delete/un-pair it .
4.0 Managing your Z-Wave Devices:
4.1 Adding Z-Wave devices:
1. Device Operation Menu has 3 options - Add, Remove and Refresh etwork.
2. To pair a Z-Wave device with the ONT, click on the Add device icon under the Device
Operations menu.
3. The ONT goes into the pairing mode and below screen will pop up.
4. Start the inclusion mode in the slave device (Refer individual device documentation, on how
to put the smart slave device into inclusion mode)
5. fter successfully pairing the smart device a Done message will be displayed.
6. If the paired device is a preferred device, it will be shown under “All Devices” menu in
Overview Tab with correct icon type.
7. If the paired device is a non-preferred device, it will be shown under “All Devices” menu in
Overview Tab with correct icon type and with unsupported text inside icon.
8. If the paired device is an unknown device type, it will be shown under “Unknown” Rooms in
Rooms tab, with unknown icon type.
4.2 Removing a Z-Wave devices:
1. To un-pair a Z-Wave device from the ONT, click on the Remove icon in the device operations
menu.
2. The ONT goes into the unpairing mode. ONT will now wait for the device to be excluded.
3. Start the Exclusion mode of the slave device (Please refer the individual device
documentation on how to put the smart device into exclusion mode)
4. fter successfully Unpairing the smart device a Done message will be displayed.
5. Device is automatically removed from assigned Rooms and automation
rules/scenarios/schedules.
6. ll preferred, non-preferred and unknown paired devices can be unpaired using the above
methods.

10
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
5.0 Controlling Z-Wave Devices:
User can control the paired Z-Wave devices using Nokia Smart Home pp, like dim home lighting to 50
%, Turn on/off smart plug, etc., based on the device capabilities
*Paired repeater will not be displayed in mobile pp, as user can’t do any action on repeater.
5.1 Controlling On/Off Plug:
Paired ON/OFF plug can be either in ON or OFF status. Plug can be turned ON/OFF from mobile pp
Tap on the icon to turn the bulb ON
Tap on the icon to turn the bulb OFF
When an on/Off switch with metering capability device is paired to ONT, mobile pp will show On/Off
icon and metering icon. Metering icon will display total power consumption in Kwh
5.2 Controlling Dimmer:
Paired dimmer can be either ON/OFF/dimmed to a value using Nokia Smart Home Mobile pp.
Tap on the icon to open a pop-up window and change the dimming value, by sliding and click
OK button
5.3 Controlling Lamp Mount:
Tap on the icon to turn Lamp Mount ON
Tap on the icon to turn the Lamp Mount OFF
5.4 Controlling Door Lock:
Tap on the icon to close/arm the Door lock
Tap on the icon to Open/dis-arm the Door lock

11
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
5.5 Controlling Siren:
Tap on the icon to switch ON the siren
Tap on the icon to switch OFF the siren
5.6 Smoke Detector:
Icon color of Smoke Detector reflect smoke detected event.
Icon color of Smoke detector reflects smoke not detected event.
5.7 Motion Detector:
Icon color of Motion Detector, reflects motion detected event.
Icon color of Motion detector, reflects motion not detected event.
5.8 T ermostat set point
On pairing a thermostat, Mobile pp will show 4 icons, namely Heating set-points, cooling set point,
current Temperature and climate control. Set-points icon to set the desired temperature, current
temperature icon shows temperature in centigrade, climate control mode to set the mode.
5.9 Multi-Sensor value
Paired Multi-sensor will show current temperature and humidity in mobile pp as shown below.

12
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
5.10 Door Sensor
Paired door sensor will be shown in the mobile pp, as shown below. Door Open and close status is
updated as,
5.11 Plug Meter
Paired Plug meter will be shown in the mobile pp, as shown below. There will be two icons
displayed, one for ON/OFF functionality, like ON/OFF plug mentioned above and the other icon is
related to power consumption metering. Value displayed in the power metering icon is total power
consumption in Kwh
5.12 Fan Switc
Fan Switch will be shown in the mobile pp, as shown below. On clicking this Fan switch icon open a
pop-up window with slider and user can change the speed of the fan by sliding and click OK button
5.13 Power Strip
Power Strip will be shown in the mobile pp, as shown below. Based on the number of end points
supported by the connected power strip, mobile pp will display power end points in the “ ll Devices”
section of dashboard. Individual end points can be controlled from the mobile pp and it employs
on/Off capability like switch/Plug. If the power strip supports metering capability, then a separate
icon showing the total power consumption in Kwh for each end points which supports metering

13
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
measurement capability. If any of the end points supports, multi-level then corresponding end points
in the mobile pp will be shown as Dimmer.
5.14 Irrigation Controller
Irrigation Controller will be shown in the mobile pp, as shown below. If the irrigation controller
supports multiple end points, then mobile pp will show that many end points as supported in the
irrigation controller device. If the irrigation controller supports metering, then a separate end showing
total power consumption in Kwh

14
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
6.0 Device Automation
The Nokia Smart Home pp allows user to create scenes, rules and schedules, once user have logged into the
Smart Home pp. Press the utomation icon at the bottom of the screen to go into the utomation screen
6.1 Managing Rules
From the automation screen, user can add rules triggering O /OFF smart devices. To create
a rule, click on the + icon at the right side of the screen under the rules menu of the
automation screen. Enter the rule name.
User can select more than one device as a part of rule. If more than one device is selected,
all device conditions must be met for triggering the rule.
6.2 Managing Sc edules
From the automation screen, user can create schedules for Smart Home devices
Under the Schedules menu of the automation screen, click on the + icon at the right side of
the screen to create a schedule and give a name as per need

15
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
7.0 Troubleshooting Guidelines:
7.1 Factory Default
Using IOT factory reset option all Z-Wave configurations can be removed and Nokia Smart
Home ONT G-240WZ- can be brought into factory default state by following below process:
1. Open any web browser e.g. Firefox, chrome or Internet explorer in the laptop
2. Enter the following URL ( ttp://192.168.1.254/) in the address bar of the web
browser to RG WebGUI
3. Enter username and password in the log-in window (Credentials printed on t e
backside of ONT)
4. Under SmartHome>Maintenance page click “Factory Default”
5. Click “OK” button (pop-up message)
6. Now ONT will do factory default setting of IOT Gateway. It will erase all Z-Wave
configuration and restart Nokia Smart Home Gateway.
7. fter 7 to 9 minutes, IOT SW status should reach ctive, online, online as described
previously in section 2.2
Note:
Reset option should be used only when the primary controller is missing or inoperable. lso, if the
missing or inoperable controller is the primary controller for your network, resetting it will result in
the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-
include all the nodes in the network. If this controller is being used as a secondary controller in the
network, use this procedure to reset this controller only if the network primary controller is missing
or otherwise inoperable.

16
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
Appendix – A: Preferred device list
Nokia Smart Home ONT G-240WZ- is designed to work with certified Z-Wave devices. Multiple
devices from different manufacture can be included into ONT Z-Wave network. Nokia Smart Home
ONT supports the following device types and home control groups:
1) HC1 – Door Lock – Keypad/Lock box
2) HC4 – Notification Sensor
a. Smoke
b. Door/Window
c. Motion
3) HC6 – Multi-level Sensors
a. ir Temperature
b. Humidity
4) HC8 – On/Off Switch – Power Strip
5) HC9 – Light Dimmer Switch
6) HC11 – Thermostat, HV C
7) HC13 – Siren
Note: ll powered device act as a repeater regardless of the manufacturer.

17
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
NOKIA SMART HOME ONT G-240WZ-A Supported Z-Wave EU Frequency Devices
Sl.
o Vendor Model umber Device Type
1 Everspring HSM02-1 Door/Window Sensor
2 Everspring SP103-2 Motion Sensor
3
Everspring
ST814
Multi Sensor
4 TKBHome TZ68G Plug
5 Everspring N158-2 Plug with Meter
6 Fibaro FGSS -001 Smoke Detector
7 Vision ZM1601 Siren
8 TKBHome TZ67G Switch (Dimmer)
9 Danfoss
Living Connect
014G0013
Wall Thermostat
108 Merten
MEG5018
-
0000 N158
-
2
Range Extender
1
11 Everspring N145-2 Lamp Mount
12 Vision ZM-1702 Door Lock
1
The Range Extender is not visible in the Nokia Smart Home mobile app and Nokia Smart Home web interface.

18
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
NOKIA SMART HOME ONT G-240WZ-A Supported Z-Wave US Frequency Devices
Sl. o
Vendor
Model number
Device Type
1
Everspring
HSM02
Door Sensor
/ Window Sensor
2
Everspring
HSP02
Motion Sensor
3
Everspring
ST814
-
2
Multi Sensor
4
eon Lab
eotec
Z
-
Wave
smart
switch 6, Gen 5
Plug
5
Everspring
N163
-
1
Plug with meter
6
Everspring
EVS
-
SF
813
-
2
-
US
Smoke Detector
7
Everspring
EVS
-
SE812
-
US
Siren
8
Everspring
D126
Switch (Dimmer)
9
Radio Thermostat
Company of
merica (RTC)
CT
-
30
Thermostat
10
eon Labs
DSD37
-
ZWUS
Range Extender
2
11
Everspring
N145
-
1
Lamp Mount
12
Yale
YRD 210
-
ZW
-
619
-
US
Door Lock
2
The Range Extender is not visible in the Nokia Smart Home mobile app and Nokia Smart Home web interface.

19
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
Appendix – B: Technical Specification
Z-Wave Tec nical information
Implemented Z-Wave device class
Z
-
Wave
Device class
Implemented Device class
Basic Device Class
B SIC_TYPE_ST TIC_CONTROLLER (02)
Generic Device Clas
s
GENERIC_TYPE_ST TIC_CONTROLLER (02)
Specific Device Class
SPECIFIC_TYPE_PC_CONTROLLER (01)
Supported Command Class
Nokia Smart Home ONT G-240WZ- is designed to work as SIS central static controller to control
slave devices. Below is the list of supported command class:
Class id
Version
ame
5E
2
Z
-
Wave
+ Info
56
1
CRC16 Encap
59
1
ssociation Group Info
5
1
Device Reset Locally
22
1
pplication Status
72
2
Manufacturer Specific
73
1
Powerlevel
85
2
ssociation
86
2
Version
98
1
Security
Z-Wave+ Info command class (0x5E, V2)
This command class will report the information about Role type and Node type information along
with type of the icon used for installer and user
Z-Wave Plus Info Report
Node Type
NODE_TYPE_ZW VEPLUS_NODE=00
Role
Type
CONTROLLER_CENTR L_ST TIC
Installer Icon Type
01 00
User Icon Type
01 00

20
Nokia Smart Home 7368 GPON ONT - G-240WZ-A User Man al
CRC16 En-cap command class (0x56, V1)
This command class will report the information CRC16 encapsulation supported by Nokia Smart
Home ONT
Association Group Info command class (0x56, V1)
This command class will report the information about life line association group supported by Nokia
Smart Home ONT
Device reset locally command class (0x5A, V1)
This command class will report the group member of life line association that, device is reset to
factory default.
Application status command class (0x22, V1)
This command class will report the information CRC16 encapsulation supported by Nokia ONT
Manufacturer specific command class (0x72, V2)
Manufacturer specific command class is used to identify the manufacturer and device type of a
device.
Power Level command class (0x73, V1)
Power level command class is used to check the connection quality between two Z-Wave devices
Association command class (0x85, V2)
ssociation command class is used to configure end smart device to send notification/alarm/event
to gateway (ONT)
Version command class (0x86, V2)
Version command class will be used to obtain the Z-Wave and firmware version of a device
Security command class (0x98, V1)
This command class will report the security command class supported by Nokia Smart Home ONT.
This will inform the pairing device to understand that ONT is a security enabled device or not?