Nordic ID Morphic User manual

23
GETTING STARTED
Read the ‘Safety Precautions’1. chapter. See page 8.
Assemble the AC adapter. See2. page 6.
Insert a SIM card if your Mor-3. phic has the optional GSM/
GPRS. See page 5.
Insert a microSD card if you4. wish to use an optional memo-
ry extension. See page 5.
Install the battery. See page 4.5. Install the optional hand strap.6. See page 6.
Charge the battery. See page7. 6.
Power up your new Morphic.8. See page 7.
NORDIC ID MORPHIC
KEYS AND PARTS
Earphone1.
Touch screen2. Touch sensitive colour display for•
the Graphical User Interface
Select, open or drag-and-drop•
GUI objects
Use as a virtual keyboard to input•
text
GREEN key
3. By default OK or Enter•
SCAN key
4. Activate optical barcode reader•
TAB / ALT key
5. Select menu or other GUI object•
TELEPHONE KEYPAD /
6.
FUNCTION KEYS
Input numbers, letters or com-• mands
BACKSPACE
7. Erase characters•
MICROPHONE
8.
NOTE
Before using the device,
the batteries must be
fully charged. Charging
takes approx. 8 hours.
TOUCH SCREEN
Nordic ID Morphic has a touch
screen; it is planted on the backlit
color screen. Touch screen pro-
vides user an alternative method of
inputting text and having control of
the device by tapping on it with a
stylus.
NOTE
The surface of the touch screen is
vulnerable to damage. Do not use a
sharp object or press hard on the
surface with the stylus.
OPTICAL READER16. 1D laser scanner or 2D imager•
17. LOUDSPEAKER
Audible alarms and signals•
HANDSTRAP18.
BATTERY COVER19.
NORDIC ID MORPHIC USER INTERFACE
CHARGING INDICATOR LED9.
POWER key10. Press and hold for 5 seconds to• perform hardware reset
MODE / FUNCTION selection key11.
Press the Mode/Function key re-
peatedly to select one of the fol-
lowing keypad input methods:
Function: Numeric keys act as• Function keys F1 to F10
abc: Numeric keys act as lower• case letters
ABC: Numeric keys act as UPPER• CASE letters
123: Numeric keys act as numbers•
ARROW KEYS
12. Move cursor within an input field or• to navigate menus.
RED key13. By default Cancel or Esc•
DOCKING CRADLE CONNECTOR
14.
CHARGER CONNECTOR15.

45
RECHARGEABLE BATTERY
BATTERY COVER
TO DETACH THE BATTERY
COVER:
Open the locking pin by turning1. it 90 degrees anticlockwise
Lift the pin and the cover
2.
TO ATTACH THE BATTERY
COVER:
Insert the cover’s guide tabs into1. their slots in the Morphic
Shut the cover
2.
Close the locking pin by turning3. it 90 degrees clockwise
BATTERY
TO ATTACH THE BATTERY:
Open the battery cover1.
Release the metallic battery2. fastening clip by pushing it to-
wards the upper end of the Mor-
phic
Check the battery orientation by
3. visually aligning the battery’s
guide slots to their guiding tabs
in the battery compartment
Insert the battery into its com-
4. partment
Press the tips of the battery fas-
5. tening clip down to their attach-
ment slots
Press the fastening clip down
6. and at the same time slide it
towards the lower end of the
Morphic until the clip is locked
Close the battery cover
7.
TO DETACH THE BATTERY:
Open the battery cover1.
Release the metallic battery2. fastening clip by pushing it to-
wards the upper end of the Mor-
phic
Remove the battery
3.
Close the battery cover4.
INSTALLING SIM CARD
INSTALLING MICROSD CARD
The microSD card holder is inside the battery compartment. First remove the battery to access the microSD card holder.
INSTALLING SIM AND MICROSD CARDS
1. Slide and lift the cover to open
the SIM card holder
2. Insert a SIM card into grooves
in the cover 3. Close and slide the cover to lock the holder
The SIM card holder is inside the battery compartment. First remove the battery to access the SIM card holder.
1. Slide and lift the cover to
open the microSD card holder 2. Insert a microSD card into the holder 3. Close and slide the cover to lock the holder

67
TO ATTACH THE HAND
STRAP:
Undo the strap’s hook-and-loop1. fastener
Pass the end of the hook-and-
2. loop fastener under and around
the metal pin on back of the Mor-
phic
Redo the hook-and-loop fastene
3. r
Stretch the strap to hook its met-
4. al clip into the slot in the bottom
of the Morphic.
Adjust the length of the strap
5. with the hook-and-loop fastener
if necessary
TO DETACH THE HAND
STRAP:
Undo the strap’s hook-and-loop1. fastener
Detach the strap from the metal
2. pin
Detach
3. the strap’s
metal clip
from its
slot
HAND STRAP
The AC adapter is shipped with
three exchangeable adapter plugs
for EU, UK and US.
Suitable adapter plug has to be at-
tached onto the AC adapter before
first use:
Place the exchangeable adapter
1. plug to the open end of its at-
tachment slot on the power
switching unit.
Slide the adapter plug along the
2. grooves of the slot.
Press the adapter plug until it is
3. firmly locked to its place by the
locking clip.
AC ADAPTER
TO CHARGE THE
BATTERY:
Plug the AC adapter to mains1. socket
Plug the AC adapter’s cord to
2. Morphic’s charger connector
The battery charging indicator LED
in the lower right corner of the Mor-
phic shows the current charging sta-
tus. Note: You may have to boot the
Morphic once before the charging
indicator LED starts to operate.
The battery is shipped empty. The
battery may have to be charged for a
couple of minutes before the Mor-
phic can be started. It takes several
hours to fully charge the battery.
Remove the AC adapter from the
socket while not in use.
Please detach an unused AC adapt-
er from the mains socket to con-
serve electricity and the environ-
ment. Thank you.
TO POWER UP THE UNIT:
Install the battery1.
Close the battery cover2.
Co3. nnect AC adapter if the bat-
tery is empty
Pres
4. s Power key
CHARGING
RED:
Battery is being
charged
BATTERY CHARGING
INDICATOR LED
ORANGE:
Battery is more than 80% charged
but still being charged at low current
GREEN:
Battery is fully
charged
Your Morphic contains delicate elec-
tronic parts. Therefore it is vulnerable
to environmental factors such as dirt,
extreme temperatures, humidity and
mechanical stress. Treat your Mor-
phic with care. The following hints
help you to preserve your device’s
functionality and longevity.
CLEANING
The device can be wiped clean• with a damp, non-abrasive,
clean, lint-free cloth.
Do not use harsh chemicals,• strong detergents, or abrasive
cleaners to clean the device.
HANDLING
Avoid dropping the Morphic, or• bumping it against other ob-
jects. Hard impacts can damage
the device. Note that damages
caused by careless handling are
not covered by the warranty.
The touch sensitive colour dis-• play, i.e. the touch screen, is
vulnerable to mechanical stress.
Do not use sharp objects or
excess force on the touch
screen.
Avoid storing the Morphic in• dusty and dirty or extremely
humid, cold or hot conditions.
Harsh environmental factors can
shorten the life of electronic
components, damage batteries
and warp or fracture plastics or
other mechanical parts.
When the Morphic is moved• from a cold environment to a
warm environment, condensa-
tion may lead to a short circuit
inside the device. It is advisable
to allow the device to acclima-
tise for several hours, after being
brought in from the cold, before
powering up.
Try to keep your Morphic dry.• Wipe spilled liquids immediately
with a dry, non-abrasive, clean,
lint-free cloth. If moisture gets
inside your Morphic because of
condensation or spillage, open
the battery cover and remove
the battery. You may power up
the device again once it has
dried. Do not open the device
case. Opening the case voids
the warranty.
CARE AND MAINTENANCE

8
LASER
Some Morphics are
equipped with a 1D
laser scanner and are
thus Class 2 Laser products. The
laser scanner uses a low power,
visible laser diode. As with any very
bright light source, such as the sun,
the user should avoid staring di-
rectly into the light beam. Momen-
tary exposure to a Class 2 laser is
not known to be harmful.
The NORDIC ID Morphic fulfils the
regulatory requirements as follows:
Complies with 21CFR1040.10 and•
1040.11 except for deviations
pursuant to Laser Notice No. 50,
dated July 26, 2001.
EN60825-1:1994+ A1:2002•
+A2:2001
IEC60825 1:1993+A1:1997+•
A2:2001
BATTERY
Use only batteries approved by Nor-
dic ID.This device is intended for use
with Varta EasyPack 3.7V rechargea-
ble Lithium Polymer battery.
Do not disassemble the battery.• Do not short circuit the battery’s• electrical contacts.
Do not expose the battery to• direct sunlight or other heat
sources.
Dispose the battery in ecologi-• cally sound manner and accord-
ing to local laws and regulations.
SAFETY PRECAUTIONS
DANSK LASERLYF! SE IKKE IND I STRÅLEN! KLASSE 2 LASER!
DEUTSCH LASERSTRAHLEN! NICHT DIRECT IN DEN LASERSTRAHL SCHAUEN! LASER
PRODUKT DER KLASSE 2!
ENGLISH LASER LIGHT! DO NOT STARE INTO BEAM! CLASS 2 LASER!
ESPAÑOL LUZ LASER! NO MIRE FIJAMENTE EL HAZ! PRODUCTO LASER DE LA CLASE 2!
FRANCAIS LUMIERE LASER! NE PAS REGARDER LE RAYON FIXEMENT! PRODUIT LASER DE
CLASSE 2!
ITALIANO LUCE LASER! NON FISSARE IL RAGGIO PRODOTTO!
NEDERLANDS LASERLICHT! NIET IN STRAAL STAREN! KLASSE-2 LASER!
NORSK LASERLYS! IKKE STIRRINN I LYSSTRÅLEN! LASER, KLASSE 2!
PORTUGUÊS LUZ DE LASER! NÃO FIXAR O RAIO LUMINOSO! PRODUTO LASER DA CLASSE 2!
SUOMI VARO LASERSÄDETTÄ! ÄLÄ SUUNTAA SÄDETTÄ SILMIIN! LASER, LUOKKA 2!
SVENSKA VARNING LASERSTÅLNING! STIRRA EJ IN I STRÅLEN! KLASS 2 LASER!
AC ADAPTER
Use only AC adapters approved• by Nordic ID. This device is
intended for use with Nordic
Power SA115C-05 AC adapter.
Do not use the AC adapter for• any other purposes than for
COMPLIANCE STATEMENTS
CE COMPLIANCE
STATEMENT
Hereby, Nordic ID Oy declares
that this Nordic ID Morphic
product is in compliance with
the essential requirements and
other relevant provisions of Di-
rective 1999/5/EC
DANSK Undertegnede Nordic ID Oy erklærer
herved, at følgende udstyr NORDICID Morphic
overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
DEUTSCH Hiermit erklärt Nordic ID Oy, dass
sich das Gerät NORDICID Morphic in Überein-
stimmung mit den grundlegenden Anforderun-
gen und den übrigen einschlägigen Bestimmun-
gen der Richtlinie 1999/5/EG befindet.
ESPAÑOL Por medio de la presente Nordic ID
Oy declara que el NORDICID Morphic cumple
con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
ΕΛΛΗΝΙΚΗ ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Nordic ID
Oy ΔΗΛΩΝΕΙ ΟΤΙ NORDICID Morphic ΣΥΜ-
ΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙ-
ΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑ-
ΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
FRANÇAIS Par la présente Nordic ID Oy
déclare que l’appareil NORDICID Morphic est
conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
ITALIANO Con la presente Nordic ID Oy di-
chiara che questo NORDICID Morphic è con-
forme ai requisiti essenziali ed alle altre disposiz-
ioni pertinenti stabilite dalla direttiva 1999/5/CE.
NEDERLANDS Hierbij verklaart Nordic ID
Oy dat het toestel NORDICID Morphic in over-
eenstemming is met de essentiële eisen en de an-
dere relevante bepalingen van richtlijn 1999/5/EG.
NORSK NORDICID Morphic er i samsvar
med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
PORTUGUÊS Nordic ID Oy declara que este
NORDICID Morphic está conforme com os req-
uisitos essenciais e outras disposições da Directiva
1999/5/CE.
SUOMI Nordic ID Oy vakuuttaa täten että
NORDIC ID Morphic tyypin laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevi-
en direktiivin muiden ehtojen mukainen.
SVENSKA Härmed intygar Nordic ID Oy att
denna NORDICID Morphic står I överensstäm-
melse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv
1999/5/EG.
NATIONAL RESTRICTIONS IN
THE EUROPEAN UNION
When the Morphic device incorporates an op-
tional 2.4 GHz wideband transmission system
(transceiver), it imposes some restrictions on the
use of its 2.4 GHz WLAN connectivity in France,
Italy, and Latvia where restrictive use applies to
2.4 GHz band.
In Italy the end-user should apply for a license at
the national spectrum authorities in order to ob-
tain authorization to use the outdoor WLAN set-
ups and/or for supplying public WLAN access to
telecommunications and/or network services.
The outdoor WLAN set-ups may not be used in
France and in some areas the RF output power
may be limited to 10 mW EIRP in the frequency
range of 2454 – 2483.5 MHz. For detailed infor-
mation the end-user should contact the national
spectrum authority in France.
In Latvia the outdoor usage of the 2.4 GHz band
requires an authorization from the Electronic
Communications Office.
FRANCE Pour la bande 2,4 GHz, la puissance
est limitée à 10 mW en p.i.r.e. pour les équipe-
ments utilisés en extérieur dans la bande 2454 -
2483,5 MHz. Il n’y a pas de restrictions pour des
utilisations dans d’autres parties de la bande 2,4
GHz. Consultez http://www.arcep.fr/ pour de
plus amples détails.
ITALY Questo prodotto è conforme alla speci-
fiche di Interfaccia Radio Nazionali e rispetta il
Piano Nazionale di ripartizione delle frequenze in
Italia. Se non viene installato all ‘interno del pro-
prio fondo, l’utilizzo di prodotti Wireless LAN
richiede una “Autorizzazione Generale”. Consul-
tare http://www.comunicazioni.it/it/ per maggiori
dettagli.
LATVIA 2,4 GHz frekveču joslas izmantošanai
ārpus telpām nepieciešama atļauja no Elektroni-
sko sakaru direkcijas. Vairāk informācijas:
http://www.esd.lv.
FCC COMPLIANCE
STATEMENT
This hand-held device complies
with part 15 of the FCC Rules.
Operation is subject to the fol-
lowing two conditions: (1) This
device may not cause harmful
interference, and (2) this device
must accept any interference received, including
interference that may cause undesired opera-
tion.
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the hand-held
equipment.
FCC COMPLIANCE NOTICE
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide rea-
sonable protection against harmful interference in
a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause
harmful interference to radio or television recep-
tion, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.• Increase the separation between the equip-• ment and receiver.
Connect the equipment into an outlet on a• circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/• TV technician for help.
charging the Morphic’s re-
chargeable batteries.
Check the mains voltage• against those specified in the
AC adapter before plugging to
mains socket.
Use the AC adapter indoors at• normal room temperatures.
MEDICAL DEVICES
Operation of any radio transmitting
wireless equipment, including the
Morphic, may interfere with the func-
tionality of inadequately protected
medical devices. To avoid potential
interference, a minimum separation
of 20 centimetres (8 inches) between
a wireless device and an implanted
medical device, such as a pacemak-
er, hearing aid, or cardioverter-defi-
brillator, is recommend by the manu-
facturers of medical devices. Consult
a physician or the manufacturer of
the medical device if necessary.
POTENTIALLY EXPLOSIVE
ENVIRONMENTS
Switch off your device when in area
with potentially explosive atmos-
phere. Sparks in such areas could
cause fire or an explosion. Potentially
explosive environment include areas
where the air contains chemicals or
particles such as dust or other pow-
ders. Potentially explosive areas are
often, but not necessarily always,
clearly marked. Obey all signs and
instructions.

FOR A PARTICULAR USE OR NON-IN-
FRINGEMENT. THE ENTIRE RISK WITH
RESPECT TO THE SOFTWARE IS WITH
YOU. IF YOU HAVE RECEIVED ANYWAR-
RANTIES REGARDING THE SOFTWARE,
THOSE WARRANTIES DO NOT ORIGI-
NATE FROM, AND ARE NOT BINDING
ON, NORDIC ID, ITS LICENSORS OR ITS
SOFTWARE SUPPLIERS.
EXCEPT AS PROHIBITED BY LAW, NEI-
THER NORDIC ID NOR ANY OF ITS
SOFTWARE SUPPLIERS SHALL HAVE
ANY LIABILITY FOR ANY DIRECT, INDI-
RECT, SPECIAL CONSEQUENTIAL OR
INCIDENTAL DAMAGES ARISING FROM
OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THE SOFTWARE.
THIS LIMITATION SHALL APPLY EVEN
IF ANY REMEDY FAILS OF ITS ESSEN-
TIAL PURPOSE. IN NO EVENT SHALL
NORDIC ID OR NORDIC ID’S SOFTWARE
SUPPLIERS BE LIABLE FOR ANY
AMOUNT IN EXCESS OF THE INITIAL
LICENSE FEE NORDIC ID RECEIVED
FROM YOU FOR THE NORDIC ID DE-
VICE IN THE CASE OF NORDIC ID OR
U.S. TWO HUNDRED AND FIFTY DOL-
LARS (U.S. $250.00) IN THE CASE OF NOR-
DIC ID’S LICENSORS OR SOFTWARE
SUPPLIERS.
TERMINATION
Nordic ID, its licensors and its software suppliers
reserve the right to terminate this EULA if You
violate any term or condition of this EULA. If
You assert any claims against Nordic ID, its licen-
sors or software suppliers over patents that You
think might apply to Software (including a cross-
claim or counterclaim in a lawsuit) Your license to
the Software ends automatically.
In the event of termination, You must stop using
the Software and You shall immediately return to
Nordic ID, all Software and any copies thereof
and related Documentation and certify to Nordic
ID that You have done so. The provisions of this
paragraph of this EULA and any other material
provisions of this EULA shall survive any termi-
nation of this EULA.
GENERAL PROVISIONS
You agree that You will not export or import any
portion of the Software to any country that is not
party to either: (i) The Berne Convention of 1989,
(ii) The Universal Copyright Convention, (iii)
The Buenos Aires Convention, or (iv) a treaty
with the United States of America (U.S.A.) which
allows for the recognition of the property rights
claimed by Nordic ID or its licensors and other
software suppliers in the Software. Further the
Devices are subject to United States and Europe-
an Union export laws and regulations. You agree
to comply with all domestic and international ex-
port laws and regulations that apply to the De-
vices. These laws include restrictions on destina-
tions, end users and end use. U.S. Government
Restricted Rights. If the Device or the Software is
acquired under the terms of a U.S. Government
contract, use, duplication, and disclosure are sub-
ject to the terms of this license and the restrictions
contained in the Rights in Technical Data and
Computer Software clause at 252.227-7013
(DOD contracts); and subdivisions (a) through
(d) of 52.227-19 as applicable.
This EULA shall be governed by and construed
under the laws of Finland. Any dispute arising out
of this EULA shall be finally settled in arbitration
by a sole arbitrator in accordance with the Arbi-
tration Rules of the Central Chamber of Com-
merce, in Turku, Finland and in English language.
However Nordic ID shall be entitled to seek in-
junctive relief in a competent court. Nordic ID
may assign this EULA without the consent of
You. If any portion hereof is found to be void or
enforceable,the remaining portions of this Agree-
ment shall remain in full force and effect. Except
as expressly provided herein, this Agreement con-
stitutes the entire agreement with respect to the
license of Software and supersedes any conflicting
or additional terms.
© Nordic ID Oy, 5/2010
form; b) licensed for the purpose of making de-
rivative works; or c) redistributable at no charge
You may not sell, lease, rent, assign, sublicense or
transfer the Software except that You may transfer
all of Your rights under this EULA as part of a sale
or transfer of the Device(s). Such a sale or transfer
may only be made if You retain no copies of the
Software, You transfer all of the Software (includ-
ing any media, archival copies, Revisions and
Documentation) and the recipient agrees to abide
by the terms of this EULA. A Revision may not
be transferred unless You transfer all prior versions
of the Software. In the event of any such transfer,
You shall remain liable and responsible to Nordic
ID for the performance of all of Your duties and
obligations under this EULA.
You agree to grant Nordic ID and its independent
accountants the right to examine Your books, ac-
counts and records to verify compliance with this
EULA. In the event such an audit reveals non-
compliance, You shall promptly sustain compli-
ance and pay Nordic ID the applicable license fees
(if any)
DISCLAIMER OF WARRANTY AND LIMI-
TATION OF LIABILITY
The software is not fault tolerant and is not de-
signed, manufactured or intended for any use re-
quiring fail-safe performance in which the failure
of Software could lead to death, serious personal
injury, severe physical or environmental damage
(“High Risk Activities”). This includes the opera-
tion of aircraft, aircraft navigation or communica-
tion systems, direct life support machines or
weapons systems or nuclear facilities. Use of De-
vice in High Risk Activities is not licensed. The
Software is not warranted to be compatible with
all applications or environments. Contact the re-
seller You purchased the Device for information
about hardware and/or software compatibility.
NO WARRANTIES FOR THE SOFTWARE.
THE SOFTWARE IS PROVIDED AS IS
AND WITH ALL FAULTS.NORDIC ID, ITS
LICENSORS AND OTHER SOFTWARE
SUPPLIERS DISCLAIM ANY AND ALL
PROMISES, REPRESENTATIONS, AND
WARRANTIES WITH RESPECT TO THE
SOFTWARE, INCLUDING ITS CONDI-
TION, ITS CONFORMITY TO ANY REP-
RESENTATION OR DESCRIPTION, THE
EXISTENCE OF ANY LATENT OR PAT-
ENT DEFECTS, ANY NEGLIGENCE AND
ITS MERCHANTABILITY OR FITNESS
PROPRIETARY RIGHTS AND LICENSE
You agree that the Software constitute trade se-
crets and/or copyrighted material of Nordic ID,its
licensors, or other software suppliers. All rights,
title and interest in and to the Software (includ-
ing, without limitation, any images, photographs,
animations, video, audio, music, text, and applets
incorporated into the Software, the accompanying
media and printed materials), and any copies of
the Software are owned by Nordic ID,its licensors
or other software suppliers. You acknowledge and
agree that nothing in this EULA gives You any
right, title or interest in and to the Software except
the limited rights expressly granted herein. You
agree to maintain and reproduce all copyright and
other proprietary notices of Software.
Nordic ID hereby grants You a license to use the
Software subject to the following terms and con-
ditions:
Unless expressly provided in the Documentation,
You may use the Software only as embedded in,
for execution on, or (where the applicable Docu-
mentation permits installation on non-Nordic ID
equipment) for communication with Device. You
have no right to use Revisions unless You, at the
time of acquiring such Revision hold a valid li-
cense to the original Software and have paid the
applicable license fees (if any)
The Software is licensed, not sold. Nordic ID
hereby grants You a non-exclusive, terminable,
limited license to use the Software on the
Device(s) for Your own internal business purposes
subject to payment of applicable license fees (if
required). No other right or license is granted or
implied. You agree not to modify copy, distribute
or otherwise disclose the Software without the
prior written consent of Nordic ID. You further
agree not to reverse engineer, disassemble, or de-
compile the Software, except and only to the ex-
tent that such activity is expressly permitted by
applicable law notwithstanding this limitation.
This license shall terminate when You no longer
own or You cease to use the Device(s) on which
You are licensed to use the Software. Your rights
to the Software do not include any license, right,
power or authority to subject the Software in
whole or in part to any of the terms of an Ex-
cluded License. “Excluded License” means any li-
cense that requires as a condition of use,modifica-
tion and/or distribution of Software subject to
Excluded License, that such Software of other
software combined or distributed with such soft-
ware be a) disclosed or distributed in source code
IMPORTANT – READ CAREFULLY THIS
END USER LICENSE AGREEMENT
(“EULA”) BEFORE INSTALLING OR US-
ING THE SOFTWARE.
By using the Device on which Software is in-
stalled, You agree to be bound by the terms of this
EULA, including the warranty disclaimers and
limitations of liability provisions below. If You do
not agree to the terms of this EULA,You may not
use the Device or install the Software. Instead,
promptly contact the reseller You purchased the
Device from for instructions on return of unused
Device(s) for a refund. ANY INSTALLATION
OR USE OF THE SOFTWARE OR THE
DEVICE ON WHICH SOFTWARE IS IN-
STALLED INDICATES YOUR AGREE-
MENT TO BE BOUND BY THE TERMS
AND CONDITIONS OF THIS EULA (OR
RATIFICATION OF ANY PREVIOUS CON-
SENT).
DEFINITIONS
“Device” means the Nordic ID equipment You
acquired from Nordic ID or one of its resellers and
on which the Software was pre-installed or onto
which it is to be installed.
“Software” means the computer program(s) li-
censed and installed on the Device and/or any
Revisions thereto.Software may include computer
programs made by Nordic ID as well as operating
systems and application programs by third party
licensors or other software suppliers. The Soft-
ware includes any disks or media on which it is
recorded and any Documentation.
“Documentation” means the materials accompa-
nying the Software which describe its functions
and how to install and use the Software.
“Revision” means any correction, modification,
update, enhancement, or new version of the Soft-
ware or Documentation whether printed or in
electronic format (including but not limited to
on-line documentation).
“You” or “Your” refers to the end user licensed to
use the Software under this EULA.
“Nordic ID” means Nordic ID Oy, a company in-
corporated in Salo, Finland
RADIO MODULES
The device contains an approved radio module.
This module is identified below.
Module: SDC-SSD30AG
FCC ID:TWG-SDCSSD30AG
ВPОССЙИ
ГОСТ Р
Терминал ручной Nordic
ID Morphic удостоверен
сертификатом соответ-
ствия ГОСТ Р№POCC FI.
AE68. B13015, срок дей-
ствия с09.02.2009 до
08.02.2012, выдан органом
по сертификации продук-
ции РОСС RU.001.11AE68
ООО «КОРПОРАЦИЯ
СТАНДАРТ».
Всоответствии спротоколом №8-МРД-119,
выданным 24 декабря 2008 г. испытательной
лабораторией ИИР ЭМС ФГУП РЧЦ ЦФО,
Nordic ID Morphic отвечает требованиям реше-
ния ГКРЧ №07-20-03-001 от 7 мая 2007 г.
Терминал ручной «Nordic ID Morphic» отно-
сится кРЭС малого радиуса действия, исполь-
зование которых разрешается только впреде-
лах зданий, сооружений, закрытых промыш-
ленных искладских площадок. Срок действия
настоящего решения ГКРЧ до 01.05.2017 г.
Всоответствии сп.16 извлечения из списка
устройств, для которых обязательна регистра-
ция, Постановлением Правительства РФ от 25
июля 2007 г. N 476 регистрация Nordic ID
Morphic не требуется.
END USER LICENSE
AGREEMENT

NORDIC ID
Myllyojankatu 2 A
24100 SALO, FINLAND
tel. [phone]
fax [phone]
www.nordicid.com
SUPPORT
https://support.nordicid.com/extranet/
HEADQUARTERS
[email protected]
phone: [phone]
UK & NORTHERN IRELAND
[email protected]
phone: [phone]
GERMAN SPEAKING COUNTRIES
[email protected]
phone: [phone]
REPAIR
This device has a two year limited warranty.
Nordic ID provides repair services for its products during and after their war-
ranty period. Together with its full support and primary support partners
Nordic ID serves customers throughout Europe. The full support centers
handle both warranty and non-warranty repair services on behalf of Nordic
ID in the countries they are located in. In addition Nordic ID has a growing
network of primary support partners, who offer the first line of support to
their local customers.
Contact details of all repair centers can be found at www.nordicid.com
For any enquiries about Nordic ID repair services please contact:
[email protected] or [phone]
EU DIRECTIVE
2002/96/EC ON WASTE
ELECTRICAL AND
ELECTRONIC
EQUIPMENT (WEEE)
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER