NordicTrack E3000 User manual

USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
Model No. NTL17950
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
NordicTrack is a registered trademark of ICON IP, Inc.
2

1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 350 pounds.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 10. To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-888-
825-2588 and order part number 146148, or
see your local electronics store.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 27 if the tread-
mill is not working properly.)
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the reset/off circuit breaker.)
19. Do not attempt to move the treadmill until it is
properly assembled. (See ASSEMBLY on page
6, and HOW TO MOVE THE TREADMILL on
page 9.) You must be able to safely lift 55
pounds (25 kg) to move the treadmill.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS
3

21. When using iFIT.com programs, an electronic
“chirping” sound will alert you when the
speed and/or incline of the treadmill is about
to change. Always listen for the “chirp” and
be prepared for speed and/or incline changes.
In some instances, the speed and/or incline
may change before the personal trainer de-
scribes the change.
22. When using iFIT.com programs, you can man-
ually override the speed and incline settings
by pressing the speed and incline buttons.
However, when the next “chirp” is heard, the
speed and/or incline will change to the next
settings of the CD or video program.
23. Always remove iFIT.com CDs and videos from
your CD player or VCR and disconnect your
MP3 player when you are not using them.
24. Inspect and properly tighten all parts of the
treadmill regularly.
25. Never insert or drop any object into any
opening.
26. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
27. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
4
The decal shown has been placed on your treadmill. If the decal is
missing or illegible, please call our Customer Service Department,
toll-free, to order a free replacement decal (see ORDERING REPLACE-
MENT PARTS on page 31). Apply the decal in the location shown.

5
Thank you for selecting the revolutionary NordicTrack®
E3000 treadmill. The E3000 treadmill offers a selection
of features designed to make your workouts at home
more enjoyable and effective.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please call our Customer Service
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (ex-
cluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number of the treadmill is
NTL17950. The serial number can be found on a decal
attached to the treadmill (see the front cover of this
manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
BEFORE YOU BEGIN
Handrail
Water Bottle Holder*
*No water bottle is included.
Fan
Console
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Rear Roller
Adjustment Bolts
Pulse Sensor

6
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrench and your own Phillips screwdriver . For
help identifying the assembly hardware, see the hardware drawings below.
1. Raise the end of the Frame (not shown) until the tread-
mill can be moved on the Front Wheels (66), and care-
fully roll the treadmill off the wood pallet.
Insert the Wire Harness (108) through the Upright Plate
(115).
With the help of a second person, hold the Upright (111)
and the Upright Plate (115) against the Frame Cover
(52). See the inset drawing and make sure that the
Upright and the Upright Plate are oriented as
shown. Attach the Upright and the Upright Plate with
four Upright Bolts (113) with two Star Washers (114).
Do not tighten the Upright Bolts yet.
Washer (116)–4
Console Bolt (110)–4 3/4” Tek Screw
(91)–4
Upright Bolt (113)–4
Panel Screw
(101)–3
Frame Bolt (31)–4
Handrail Bolt (90)–4
Star Washer
(114)–4
114
114
115
52
66
113
111
108
1
111
115

7
2. Have a second person hold the console assembly near
the Upright (111). Insert the wire harness extending from
the console assembly through the hole in the top of the
Upright. Attach the console assembly to the Upright with
four Console Bolts (110) and two Star Washers (114).
Firmly tighten the four Console Bolts.
Next, connect the wire harness extending from the con-
sole assembly to the Wire Harness (108). The connec-
tors should slide together easily and snap into place.
If they do not, turn one connector and try again.
114
114
111
Console
Assembly
110
Wire Harness
110
2
3. Note: For clarity, the console assembly is not shown
in this step.
Orient the Short Panel (106) so that the indicated notches
are at the top. Have a second person hold the Short Panel
against the Upright (111), with the top of the Short
Panel flush with the top of the Upright. Route the Wire
Harness (108) down the indicated side of the Short Panel.
Next, hold the Long Panel (112) against the opposite side
of the Upright (111); make sure that the top of the Long
Panel is flush with the top of the Upright and that the
Wire Harness (108) is not pinched. Press the Long
Panel and the Short Panel (106) together, and align the
three holes in the Long Panel with the holes in the Panel
Brackets (109). Attach the Long Panel and the Short
Panel with three Panel Screws (101).
Firmly tighten the four Upright Bolts (113). 101
113
112
111
Notches
3
108
108
106
101
109
109
108
101
109

8
4. Identify the right Handrail (86) and the Left Handrail (89);
the Handrails have indented holes in the outer sides for
the heads of the Handrail Bolts (90).
Hold the Right Handrail (86) on the right side of the tread-
mill. Loosely thread two Handrail Bolts (90) into the
bracket on the Right Handrail and into the console assem-
bly. Do not tighten the Handrail Bolts yet. Attach the
Left Handrail to the left side of the treadmill in the same
way. Then, slide the Upper Handrail (93) onto the Right
and Left Handrails.
Next, slide a Handrail Bracket (32) onto the lower end of
the Right Handrail (86). Insert two Frame Bolts (31) with
two Washers (116) into the Right Handrail and the
Handrail Bracket, and finger tighten the Frame Bolts into
the Frame (28). Do not tighten the Frame Bolts yet.
Attach the lower end of the Left Handrail (89) in the same
way.
86
89
93
32
116
28
31
90
Console
Assembly
4
5. Attach the Upper Handrail (93) to the Left and Right
Handrails (86, 89) with four 3/4” Tek Screws (91) (only two
are shown); start all four Tek Screws before tightening
them.
See step 4. Firmly tighten the four Handrail Bolts (90) and
the four Frame Bolts (31).
86
91
89
93
5

9
If you purchase the optional chest pulse sensor (see page 26), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
2. Remove the indicated 3/4” Screw (95) and the Access
Door (121) from the bottom of the Console Base (98).
3. Connect the wire on the receiver (A) to the indicated wire
extending from the Console Base (98). Hold the re-
ceiver so the small cylinder is oriented as shown and
is facing the Console Base. Attach the receiver to the
plastic posts on the Access Door (121) with the two in-
cluded small screws.
4. Make sure that no wires are pinched. Reattach the
Access Door (121) with the 3/4” Screw (95). Discard the
other wires included with the receiver.
A
98
Small
Cylinder
121
95
Wire
Small
Screws
HOW TO MOVE THE TREADMILL
1. Unplug the power cord.
2. Hold the treadmill with your hands in the location shown
by the arrow at the right, and raise the end of the tread-
mill. CAUTION: To decrease the possibility of injury,
bend your legs and keep your back straight. As you
raise the treadmill, make sure to lift with your legs
rather than your back.
3. Push the treadmill to the desired location. To reduce the
risk of injury, use extreme caution while moving the
treadmill.
4. Carefully lower the treadmill until it is resting on the floor. Wheels

10
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-888-825-
2588 and order part number 146148.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin

11
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When the manual mode of the con-
sole is selected, the speed and incline of the treadmill
can be changed with the touch of a button. As you ex-
ercise, the console will display continuous exercise
feedback. You can even measure your heart rate using
the built-in handgrip pulse sensor or the optional chest
pulse sensor (see page 26).
In addition, the console features fifteen preset pro-
grams that automatically control the speed and incline
of the treadmill as they guide you through effective
workouts. You can even create your own custom work-
out programs and save them in memory for future use.
The console also offers four heart rate programs that
control the speed and incline of the treadmill to keep
your heart rate near a target heart rate during your
workouts. Note: You must wear the optional chest
pulse sensor to use the heart rate programs.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com technology is like having a per-
sonal trainer in your home. Using a stereo audio cable,
you can connect the treadmill to your portable stereo,
home stereo, computer, or VCR and play special
iFIT.com MP3, CD, and video programs (iFIT.com MP3
programs, CDs, and videocassettes are available sepa-
rately). iFIT.com programs automatically control the
speed and incline of the treadmill as a personal trainer
guides you through every step of your workout; high-
energy music provides added motivation. To purchase
and download iFIT.com MP3 programs, go to
www.iFIT.com. To purchase iFIT.com CDs or video-
cassettes, call toll-free 1-888-825-2588.
With the treadmill connected to your computer, you
can also go to www.iFIT.com and access iFIT.com
programs directly from our Web site. See
www.iFIT.com for more information.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset
program, see page 15. To create and use a custom
program, see pages 17 and 18. To use a heart rate
program, see page 19. To use an iFIT.com MP3, CD,
or video program, see page 23. To use an iFIT.com
program directly from our Web site, see page 25.
Clip
Note: If there is a thin sheet of plastic
on the face of the console, remove it. Key

12
HOW TO TURN ON THE POWER
Plug in the power cord
(see page 10). Next,
locate the reset/off circuit
breaker on the frame near
the power cord, and switch
the circuit breaker to the
reset position.
Stand on the foot rails of the treadmill. Find the clip at-
tached to the key (see the drawing on page 11) and at-
tach the clip securely to the waistband of your clothes.
Next, insert the key into the console. After a moment,
the display will light. Note: When the power is turned
on, the program that was selected the last time the
Save button was pressed will automatically be rese-
lected. If the Save button has not yet been pressed,
the manual mode will be selected.
Test the clip by carefully taking a few steps back-
ward until the key is pulled from the console. If the
key is not pulled from the console, adjust the posi-
tion of the clip as needed.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
See HOW TO TURN ON THE POWER above.
Designate yourself as user A, B, C, or D.
The console can save program settings for up to
four different users. To designate yourself as user
A, B, C, or D, press the Personal Settings button
labeled A, B, C, or D.
Select the manual mode.
To select
the manual
mode, press
the
Programs
button re-
peatedly
until a track appears in the center of the display.
Make sure that the word “Programs” does not ap-
pear below the track.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the twelve
1-Step Speed buttons.
If the Start button or the
Speed increase button
is pressed, the walking
belt will begin to move at
1 mph. As you exercise,
change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change in incre-
ments of 0.1 mph; if a button is held down, the
speed setting will change in increments of 0.5
mph. Note: After the buttons are pressed, it may
take a moment for the walking belt to reach the se-
lected speed setting.
If one of the 1-Step Speed buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the 1-Step Speed
buttons.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 28).
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the twelve 1-Step Incline buttons.
Each time the Incline in-
crease or decrease but-
ton is pressed, the incline
will change by 0.5%.
Note: After the buttons
are pressed, it may take a
moment for the treadmill to reach the selected in-
cline setting.
If one of the 1-Step Incline buttons is pressed, the
incline will gradually increase until it reaches the
selected incline setting.
5
4
3
2
1
Reset
Position
Track

13
Adjust the cushioning system as desired.
The treadmill features a
cushioning system that
reduces the impact as
you walk or run on the
treadmill. There are fif-
teen firmness levels. To
increase the firmness of
the walking platform, turn
the Active Response
Cushioning knob coun-
terclockwise. To decrease the firmness, turn the
knob clockwise. The display will show the se-
lected firmness level. If you wish to save the se-
lected firmness level, press the Save button. Note:
A clicking sound may be heard when the cushion-
ing system is being adjusted.
Follow your progress with the display.
When the
manual
mode or the
iFIT.com
mode is se-
lected, the
center of the
display will show a 1/4-mile track. As you walk or
run, the indicators around the track will light in suc-
cession until the entire track is lit. The track will
then darken and the indicators will again begin to
light in succession.
The lower right zone of
the display will show a
training zone bar that in-
dicates the approximate
intensity level of your ex-
ercise. If eight indicators
in the bar are lit, for ex-
ample, the bar shows
that your pace is ideal for
aerobic exercise.
The Incline/Carbs zone
of the display will show
the incline level of the
treadmill and the approxi-
mate number of grams of
carbs you have burned.
Note: Each time the incline changes, the display
will show the incline setting for a few seconds.
The Heart Rate zone of
the display will show
your heart rate when you
use the handgrip pulse
sensor or the optional
chest pulse sensor.
The Time zone of the dis-
play will show the elapsed
time. Note: When a pro-
gram is selected, the dis-
play will show the time re-
maining in the program
instead of the elapsed time.
The Calories zone of the
display will show the ap-
proximate number of
calories you have
burned.
The Pace/Speed zone of
the display will show the
speed of the walking belt
and your pace (pace is
measured in minutes per
mile).
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find which
unit of measurement is
selected, hold down the
Stop button while inserting the key into the con-
sole. An “E” for English miles or an “M” for metric
kilometers will appear in the Pace/Speed zone of
the display. Press the Speed increase button to
change the unit of measurement. When the de-
sired unit of measurement is selected, remove the
key and then reinsert it. Note: For simplicity, all
instructions in this section refer to miles.
The Odometer zone of
the display will show the
distance that you have
walked or run during your
workout.
To see the total number of miles that you have
walked or run since the treadmill was purchased,
press the Odometer button; the words “Total Miles”
and the total number of miles will appear in the dis-
play.
7
6
Track

14
To see the total number of miles that you have
walked or run during a recent period of time, such
as the most recent month, press the Odometer
button again; the words “My Miles” and the total
number of miles will appear in the display. To reset
this number, hold down the Odometer button for a
few seconds.
To again see the distance that you have walked or
run during your workout, press the Odometer but-
ton again.
To reset the display, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
Note: If you
use the
handgrip
pulse sen-
sor and the
optional
chest pulse
sensor at
the same
time, the
console will
not display your heart rate accurately. Before
using the handgrip pulse sensor, remove the clear
plastic film from the metal contacts. In addition,
make sure that your hands are clean.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, the
heart symbol in the Heart Rate zone of the display
will appear, one or two dashes will appear, and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
Turn on the fans if desired.
To turn on the fans at low
speed, press the
AutoBreeze Fans button;
the number 1 will appear
below the word “Fan” in
the display. To turn on
the fans at medium speed, press the button a sec-
ond time; the number 2 will appear. To turn on the
fans at high speed, press the button a third time;
the number 3 will appear. To select the Auto
mode, press the button again; the word “Auto” will
appear. When the auto mode is selected, the
speed of the fans will automatically increase and
decrease as the speed of the walking belt in-
creases and decreases.
To turn off the fans, press the AutoBreeze Fans
button again. Note: If the fans are left on when the
walking belt is stopped, the fans will automatically
turn off after a few minutes.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest set-
ting. Next, remove the key from the console and put
it in a secure place. Note: If the display remains lit
after the key is removed, the console is in the
“demo” mode. See page 26 and turn off the
demo mode.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
10
9
8
Contacts

15
HOW TO USE A PRESET PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Identify yourself as user A, B, C, or D.
See step 2 on page 12.
Select one of the preset programs.
To select
one of the
fifteen pre-
set pro-
grams,
press the
Programs
button re-
peatedly
until the words “Weight Loss,” “Aerobic,” or
“Performance” and the number 1, 2, 3, 4, or 5 ap-
pear in the lower center of the display.
As each preset program is selected, the maximum
speed setting of the program and the maximum
incline setting of the program will flash in the dis-
play for a few seconds. The Time zone of the dis-
play will show how long the program will last. A
profile of the speed settings of the program will
scroll across the matrix in the center of the dis-
play.
Adjust the intensity level of the program if
desired.
The lower right zone of
the display will show the
intensity level of the se-
lected program; there
are fifteen intensity lev-
els. If desired, turn the
Program Intensity dial to
increase or decrease the
intensity level of the pro-
gram. If you change the
intensity level, the new
maximum speed setting of the program and the
new maximum incline setting of the program will
flash in the display for a few seconds. In addition,
the profile in the matrix will change to show the
new speed settings of the program. If you wish to
save the new intensity level of the program for fu-
ture workouts, press the Save button.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive seg-
ments.
The speed
setting for
the first seg-
ment will be
shown in the
flashing
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next twelve segments will be shown
in the twelve columns to the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the speed
setting and/or incline setting will flash in the dis-
play to alert you.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second seg-
ment. Note: If all seven of the indicators in the
Current Segment column are lit, the speed settings
may also move downward so that only the highest
indicators appear in the matrix.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
5
4
3
2
1
Current Segment

16
If the speed and/or incline settings of the program
are too high or too low, you can change the inten-
sity level of the program at any time by turning the
Program Intensity dial. If you wish to save the new
intensity level of the program for future workouts,
press the Save button.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
Adjust the cushioning system as desired.
See step 6 on page 13.
Follow your progress with the display.
See step 7 on page 13.
Measure your heart rate if desired.
See step 8 on page 14.
Turn on the fans if desired.
See step 9 on page 14.
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the in-
cline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a safe place. Note: If the display remains lit
after the key is removed, the console is in the
“demo” mode. See page 26 and turn off the
demo mode.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
10
9
8
7
6

17
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Identify yourself as user A, B, C, or D.
See step 2 on page 12.
Select one of the custom programs.
To select a
custom pro-
gram, press
the
Programs
button re-
peatedly
until the
words “My
Design” and the number “1” or “2” appear in the
display.
Note: If the custom program has not yet been
defined, only three columns of indicators will
scroll across the matrix in the center of the
display. If more than three columns of indica-
tors appear, see HOW TO USE A CUSTOM
PROGRAM on page 18.
Press the Start button or the Speed increase
button and program the desired speed and in-
cline settings.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Refer to the
matrix. Each
custom pro-
gram is di-
vided into
one-minute
segments.
One speed setting and one incline setting can be
programmed for each segment. The speed setting
for the first segment will be shown in the flashing
Current Segment column of the matrix. (The in-
cline settings are not shown in the matrix.) To pro-
gram a speed setting and an incline setting for the
first segment, simply adjust the speed and incline
of the treadmill as desired by pressing the Speed
and Incline buttons. Every few times a Speed but-
ton is pressed, an additional indicator will appear
or disappear in the Current Segment column.
When the first segment of the program ends, a se-
ries of tones will sound and the current speed set-
ting and the current incline setting will be saved in
memory. The three columns of indicators will then
move one column to the left, and the speed set-
ting for the second segment will be shown in the
flashing Current Segment column. Program a
speed setting and an incline setting for the second
segment as described above.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
When you are finished exercising, remove the
key from the console.
See step 10 on page 16.
5
4
3
2
1Current Segment

18
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Identify yourself as user A, B, C, or D.
See step 2 on page 12.
Select one of the custom programs.
To select a
custom pro-
gram, press
the
Programs
button
repeatedly
until the
words “My
Design” and the number “1” or “2” will appear in
the display.
As each custom program is selected, the maxi-
mum speed setting of the program and the maxi-
mum incline setting of the program will flash in the
display for a few seconds. The Time zone of the
display will show how long the program will last. A
profile of the speed settings of the program will
scroll across the matrix in the center of the dis-
play. Note: If only three columns of indicators
scroll across the matrix, see HOW TO CREATE
A CUSTOM PROGRAM on page 17.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each custom program is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed setting and/or incline set-
ting may be programmed for two or more consec-
utive segments.
The speed
setting for
the first seg-
ment will be
shown in the
flashing
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next nine segments will be shown in
the columns to the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the
speed setting and/or incline setting will flash in the
display to alert you.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To in-
crease the length of the program, first wait until
the program is completed. Then, press the Start but-
ton and program speed and incline settings for as
many additional segments as desired. When you
have added as many segments as desired, press
the Stop button twice. To decrease the length of
the program, press the Stop button twice at any
time before the program is completed.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
4
3
2
1Current Segment

19
Adjust the cushioning system as desired.
See step 6 on page 13.
Follow your progress with the display.
See step 7 on page 13.
Measure your heart rate if desired.
See step 8 on page 14.
Turn on the fans if desired.
See step 9 on page 14.
When you are finished exercising, remove the
key from the console.
See step 10 on page 16.
HOW TO USE A HEART RATE PROGRAM
Follow the steps below to use a heart rate program.
Put on the optional chest pulse sensor.
You must wear the optional chest pulse sensor
(see page 26) to use a heart rate program.
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 12.
Identify yourself as user A, B, C, or D.
See step 2 on page 12.
Select a heart rate program.
To select a
heart rate
program,
press the
Programs
button re-
peatedly until
the words
“Heart Rate”
and the number 1, 2, 3, or 4 appear in the lower
center of the display.
As each heart rate program is selected, a profile
of the target heart rate settings of the selected
program will scroll across the matrix in the center
of the display. Note: If heart rate program 4 is se-
lected, a heart beat symbol instead of a profile will
scroll across the matrix.
Enter a maximum target heart rate setting.
When a heart rate pro-
gram is selected, the
words “Heart Rate” will
appear in the Heart Rate
zone of the display and
the maximum target heart
rate setting of the program will flash. If desired,
press the Heart Rate increase and decrease but-
tons to change the maximum target heart rate set-
ting. (See the heart rate chart on page 29 for
heart rate guidelines.) To save the new maxi-
mum target heart rate setting for future workouts,
press the Save button.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each heart rate program is divided into 20 one-
minute segments. One target heart rate setting is
programmed for each segment. Note: The same
target heart rate setting may be programmed for
two or more consecutive segments. If heart rate
program 4 is selected, the maximum target heart
rate setting is programmed for all segments.
6
5
4
3
2
1
9
8
7
6
5
CAUTION: If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether the
medication will affect your exercise heart rate.

20
The target
heart rate
setting for
the first seg-
ment will be
shown in the
flashing
Current Segment column of the matrix. The target
heart rate settings for the next twelve segments
will be shown in the columns to the right.
If heart rate
program 4 is
selected, the
target heart
rate settings
will not be
shown in the
matrix. Instead, a heart beat symbol will scroll
across the matrix.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, the speed
setting and/or incline setting will flash in the dis-
play. When the first segment ends, all target heart
rate settings will move one column to the left. The
target heart rate setting for the second segment
will then be shown in the flashing Current
Segment column.
During each segment, the console will compare
your heart rate to the target heart rate setting. If
your heart rate is too far below or above the target
heart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate set-
ting. If the speed reaches the maximum speed
setting of the program (7.5 mph) and your heart
rate is still too far below the target heart rate set-
ting, the incline of the treadmill will also increase
to bring your heart rate closer to the target heart
rate setting.
The program will continue in this way until the tar-
get heart rate setting for the last segment is
shown in the Current Segment column and the
last segment ends. The walking belt will then slow
to a stop.
If the speed and/or incline settings of the program
are too high or too low, you can change the inten-
sity level of the program at any time by pressing
the Heart Rate increase and decrease buttons to
change the maximum target heart rate setting. If
you wish to save the new maximum target heart
rate setting for future workouts, press the Save
button.
If your pulse is not detected during the program,
the letters “PLS” will flash in the Heart Rate zone
of the display and the speed and incline of the
treadmill may automatically decrease until your
pulse is detected. If this occurs, see the instruc-
tions included with the optional chest pulse sensor.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the console com-
pares your heart rate to the target heart rate, the
speed and/or incline of the treadmill will automati-
cally change to bring your heart rate closer to the
target heart rate.
Adjust the cushioning system as desired.
See step 6 on page 13.
Follow your progress with the displays.
See step 7 on page 13.
Turn on the fans if desired.
See step 9 on page 14.
When you are finished exercising, remove the
key.
See step 10 on page 16.
10
9
8
7
Current Segment