John Lewis 800/86402 User manual

PRE-ASSEMBLY PREPARATION
Necessary Tools
Please ensure instructions are read in full before attempting to assemble this product.
For product support or spare parts please call
the John Lewis Helpline ;
T: 01244 689949
E: [email protected]m
Please check the pack contents before attempting to assemble this product. A full checklist of components is given in
this leaflet. If any components are missing please contact the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the John
Lewis Helpline on 01244 689949 or email [e-mail].
John Lewis
Keates Bed
Double Stock Code: 800/86402, 800/86412, 800/86422
Kingsize Stock Code: 800/86403, 800/86413, 800/86423

JCBC M6 x 25mm Bolt x 2
Fittings and parts checklist
D
EB
C
A
M4 ALLEN KEY x1
M5 ALLEN KEY x1
Headboard x1
Footboard x1
Side Rail x2
Slats x30
Centre Rail x1
Legs x 2
Side Plastic Cap x30
Centre Plastic Cap x15
1
2
3
5
4
6

Place Legs (6) into holes on the underside of the Footboard (2) turn clockwise to secure into place.
Step by step assembly instructions
Step One
Preinserted Nut
Foot Board
Leg
Place metal fixing on Side Rails (3 ) over pre-inserted bolts in Headboard (1 ) and Footboard (2)
tighten bolts with Allen Key M5 (E) to secure parts together.
M5
Step Two
M5 x1

fig. 6
fig. 5
Insert Centre Rail (5) into the brackets in the centre of the Headboard (1) and Footboard (2).
Push down fully and secure in place using M6 x 25mm bolt (A) tighten screw with Allen Key M4 (D).
M4
M6 x 25mm
M6x25mm x2
Step Three
M4 x1
Slat
Centre Plastic Cap
Center Rail
Slat
Side Rail
Side Plastic Cap
Slat
Fig
Fi
B.
C.
4.
Side Plastic Cap x30
Centre Plastic Cap x15
Slats x30
Step Four
The two Slats (4) can be secured to the bed by inserting the slat with the Side Plastic Cap (C) pin into
the both side platform rail as shown in fig. 5. Then, press the Centre Plastic Cap (B) pin into the
center rail as shown in fig. 6. Repeat the step for further 14 times.

Step Five
Bed is ready to use.

Care and Maintenance
This Keates bed should be cleaned using a soft damp cloth and dried immediately. Do not use a very wet
cloth or allow any liquid contact for a long period of time as this can permanently damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on going discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
Safety Instructions
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent adult. No
liability will be accepted for damage or injury caused by incorrectly insalled or assembled furniture. During
assembly children should be kept away from the product due to possible risk of injury. Do not use this item if any
components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid personal injury or
damage to the furniture. Please be careful to retain all fittings when doing this.
If you require any addi onal informa on or have any issues with this product please call the John Lewis
Helpline on 01244 689949 or email [e-mail]
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com