Northern Industrial Tools 16IN.WAREHOUSE BARN User manual

1
16IN.WAREHOUSE BARN
PENDANT LIGHT
OWNER’S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS
before operating. Failure to follow the safety rules and other basic safety precautions
may result in serious personal injury.
Item
#
28710

2

3
Thank you very much for choosing a Northern Industrial Tools product! For future reference, please
complete the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to
become familiar with this product before you begin using it.
This light is designed for certain applications only. The distributor cannot be responsible for issues
arising from modification. We strongly recommend this light not be modified and/or used for any
application other than that for which it was designed. If you have any questions relative to a particular
application, DO NOT use the light until you have first contacted the distributor to determine if it can or
should be performed on the product.
For technical questions please call 1-800-222-5381.
INTENDED USE
The 16in. warehouse barn pendant light is perfect for your warehouse, yard, barn, etc. It has a durable
19-ga. aluminum lamp cover and is powder-coated for rust resistance. The metal cage protects the bulb
from damage.
TECHNICAL SPECIFICATIONS
Item Description
Material Aluminum
Finish Powder-coat
Size 16in. Shade Cover
Bulb Requires E26 bulb (not included)
Lamp type 110 Volt, 200W, 60Hz
GENERAL SAFETY RULES
• WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in serious injury.
• CAUTION: Do not allow persons to operate or assemble this light until they have read this
manual and have developed a thorough understanding of how the light works.
• CAUTION: Risk of fire. Install fixture at least 4FT. from the ground. Suitable for wet
locations.

4
• WARNING: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions or situations that could occur. It must be understood by the
operator that common sense and caution are factors that cannot be built into this product, but must be
supplied by the operator.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY CONSIDERATIONS
•Proper installation of this product requires the installer to have a good understanding of circuitry.
•Please operate your barn light according to Operation Method and retain the proper operation
procedures.
•Before attempting to install your barn light, ensure power to outlet box is off for your own safety.
• WARNING: Connect green fixture wire to grounding screw in junction box.
• WARNING: Do not touch the steel parts when it is working.
•Do not use any harsh abrasives, detergents or anything containing ammonia to clean your barn
light.
•Bulb is not included with the barn light; use a standard E26 bulb only.
•FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD
RESULT IN DAMAGE TO THE PRODUCT OR SERIOUS INJURY TO YOU!
LIGHT USE AND CARE
• Do not modify the light in any way. Unauthorized modification may impair the function and/or
safety and could affect the life of the product. There are specific applications for which the barn
light was designed.
• Check damaged or worn out parts before using the barn light. Broken parts will affect the barn
light operation. Replace or repair damaged or worn parts immediately.
ASSEMBLY
1. Disconnect power at main electrical box before installing fixture.
2. Insert the screws (8) through the mounting base (7). Run wires from the junction box through
mounting base (7), gasket (6).
3. Attach the ballast black wire to the supply black wire and the ballast white wire to supply white
wire, using wire nuts (12) provided.

5
4. Connect 2 green fixture wires (1 in the cord and 1 on the back plate) to grounding screw in the
junction box.
5. Attach the mounting base (7) on the junction box by tapping screws (10). Attach the back plate (5)
to the mounting base (7); make sure the screws (8) insert into the hole on the back plate (5).
6. Align the mounting base (7) and back plate (5) by tightening the cap nut (9) to the screws (8).
** Adjust wire for high or low ceiling: Loosen the wire lock on the 10 ft. wire, move it to the suitable
location on the wire, then tighten it. Cut off the extra parts, and then connect the wire (refer to steps 3 and
4).
OPERATION
•Make sure to shut down the power supply. Remove the cage (2) and mount a standard E26 bulb
into the light, then mount the cage. Turn on the power supply. Refer to the chart below for
acceptable bulb types:
Watts Bulb Type
100 Watts Max. A19 Lamp, E26 Base
200 Watts Max. A21 Lamp, E26 Base
MAINTENANCE
• Maintain your barn light. It is recommended that the general condition of any barn light be
examined before it is used. Keep your barn light in good repair by adopting a program of
conscientious repair and maintenance. Have necessary repairs made by qualified service
personnel.

6
PARTS DIAGRAM& PARTS LIST
Part No. Description Quantity
1 Shade 1
2 Cage 1
3 Lamp Holder 1
4 Wire 1
5 Back Plate 1
6 Gasket 1
7 Mounting Base 1
8 Screws 2
9 Cap Nut 2
10 Tapping Screws
（ no display ） 2
11 Wall plug
（ no display ） 2
12 Wire nut
（ no display ） 3

7
For technical questions please call 1-800-222-5381.
APPENDIX: A SKETCH MAP FOR LIGHT MOUNTING
Grounding wire
Junction Box by others
Wall Plug
Black to null wire
White to live wire
tapping screw
Grounding wire on the back plate

8
WARRANTY
1-year limited warranty
Distributed by:
Northern Tool + Equipment Co., Inc.
Burnsville, Minnesota 55306
NorthernTool.com

9
Made in China

10