Nova NVA-FT06 User manual

Operator’s Manual
Publish Date: 7-1-22
NVA-FT06
North America
©NOVA Welding Industries
WIRELESS TIG FOOT PEDAL
2.4 GHz
MODEL: NVA-FT06
SERIAL NUMBER:
APPLICATION:
FCC PEDAL/TRANSMITTER ID:
FCC RECEIVER ID:
OTHER:

2
TABLE OF CONTENTS
SPECIAL NOTICE AND CALIFORNIA PROPOSITION 65 WARNING, FCC Usage Information 3
SAFETY DISCLAIMER AND HF WARNING 4
SPECIFICATIONS, COMPATIBILITY NUMBERS 8
COMPONENT ID 9
INTRODUCTORY NOTICE ON SHIPPING AND PEDAL TOP SERVICING 10
UNPACKING YOUR UNIT 11
PAIRING INFORMATION 11
CONNECTING THE BATTERY WIRES BEFORE USE 12
CHARGING THE BATTERY 12
CONNECTING THE RECEIVER DONGLE TO WELDER 12
OPERATION OF THE NOVA WIRELESS PEDAL 13
TROUBLESHOOTING 15
RECYCLE. DO NOT DISCARD THIS PRODUCT IN THE TRASH!
This Wireless Pedal has been designed for a long life. However, in
the event part(s) or all of this product becomes non serviceable:
• Do not discard this product or its parts in general waste. Do not
burn or attempt to destroy this product or damage it further.
• Reuse or Recycle Waste Electrical And Electronic Equipment
(WEEE) by disposing of it at a designated recycling or collection
facility.
• Contact your local government or disposal/collection facility for
recycling information and locations. Or contact NOVA for further
recycling or repair information.

3
NOTICE:
Product Specications and features are subject to change without notice. While every at-
tempt has been made to provide the most accurate and current information possible at the
time of publication, this manual is intended to be a general guide and not intended to be
exhaustive in its content regarding safety, welding, or the operation/maintenance of this
unit. Due to multiple variables that exist in the welding eld and the changing nature of it
and of the NOVA Welding Industries does not guarantee the accuracy, completeness, au-
thority or authenticity of the information contained within this manual or of any infor-
mation offered during the course of conversation or business by any NOVA employee or
subsidiary. The owner of this product assumes all liability for its use and maintenance.
NOVA does not warrant this product or this document for tness for any particular pur-
pose, for performance/accuracy or for suitability of application. Furthermore NOVA does
not accept liability for injury or damages, consequential or incidental, resulting from the
use of this product or resulting from the content found in this document or accept claims
by a third party of such liability.
WARNING!
California Proposition 65 Warning:
This product, when used for welding or cutting, produces fumes or gases which
contain chemicals known to the State of California to cause birth defects and, in
some cases, cancer. (California Health & Safety Code § 25249.5 et seq.)
Warning: Cancer and/or Reproductive Harm
www.P65warnings.ca.gov
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Relocate or reorient the transmitter (pedal) and/or receiving antenna (dongle).
• Increase the separation distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult NOVA, the installing electrician or an experienced radio/TV technician for help.
If interference cannot be eliminated, discontinue use and contact NOVA.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

4
Safe operation and proper maintenance is your responsibility.
NOVA Welding Industries is dedicated to keeping safety a top priority. While we have compiled this operator’s manual to instruct you in basic
safe operation and maintenance of your NOVA product, it is no substitute for observing safe welding practices and behavior. Safe welding and
related operations require basic knowledge, experience and ultimately the exercise of common sense. Welding does signicant hazards to your
health and life! Exercise extreme caution and care in all activities related to welding or cutting. Your safety, health and even life depends upon
it.
WARNING! If you do not have proper knowledge or capability to safely install and operate this foot pedal, do not use this pedal
until proper training has been received.
While accidents are never planned, preventing an accident requires careful planning. Stay alert! Keep
wires and chargers properly stored. Keep pedal switched to “OFF” when not in use.
Please carefully read this manual before you install and operate your NOVA TIG foot pedal.
The warranty does not cover damage or harm created by improper use. neglect of the pedal or failure to follow safe operating practices.
NOTICE:
• Welding and cutting operations may generate undesirable High Frequency (HF) and EMF
energy. This can interfere with surrounding electronic equipment such as computers, routers,
CNC equipment, televisions, communication equipment, radios, fluorescent lighting, naviga-
tion equipment, etc.
• This unit uses low level radio frequencies
• Only use licensed electricians or qualied electronics installers familiar with similar electronic
equipment to install this equipment for use.
• The user is responsible to have any suspected interference resulting from the installation and
use of this product investigated and corrected by a qualied individual in a prompt manner.
• If notied by the FCC that the unit is causing interference, you must stop using this equip-
ment at once.
• Do not attempt to modify this equipment or change the way this unit operates in any way.
• Keep the unit in good repair, including batteries, antennas and cables.

5
Safety Warnings, Dangers, Cautions and Instructions
NOTICE. This unit manual is intended for users with basic knowledge and skillset in weld-
ing. It is your responsibility to make certain that the use of this welder is restricted to per-
sons who have read, understand and follow the warnings and instructions in this manual. If
you or the operator needs further instruction, contact NOVA at 1-877 755-9353.
WARNING! High Frequency (HF) energy can interfere with the operation of pacemakers and
can damage pacemakers. Consult with your physician and pacemaker manufacturer before
entering an area where welding and cutting equipment is in operation and before using this
welder. Some pacemakers have limited shielding. Alert any users or customers of this po-
WARNING! Use approved safety glasses with wrap around shields and sides while welding
and working in the weld area or serious eye damage or loss of vision may result. Use a
grinding shield in addition to the safety glasses during chipping and grinding operations.
WARNING! When welding always use an approved welding helmet or shielding device
equipped with at least an equivalent of a shade 9 or greater. Increase the shade number
rating as amperage increase over 100 amps. Inspect helmet for cracks in lenses and in the
helmet. Keep lens covers in good condition and replace as necessary.
WARNING! Welding/cutting operations carry inherent risks which include but not limited to
possible cuts burns, electrical shocks, lung damage, eye damage and even death. Take all
appropriate measures to use proper Personal Protective Equipment (PPE). Always use
leather welding gloves, closed toe (preferably reinforced or steel toe leather shoes, and long
-sleeved flame resistant clothing (i.e. denim). Do not wear Poly/Nylon blend materials.
DANGER! Welding/cutting poses shock and electrocution risks. Keep this welding equip-
ment dry. Do not weld in the rain or where moisture accumulates. Use dry, rubber soled
shoes, gloves and clothing when welding. Do not rest or contact work clamp (ground) when
welding. Keep all parts of the body insulated from the part being welded when possible. Do
not touch terminals or connections while the unit is on. Consider all parts to be “live” at all
times even if no live work is being performed. Do not use frayed welding cables.
CAUTION! Fires are possible but also preventable while welding. Always remove flammable
rags, papers, and other materials from the weld area. Keep rags stored in an approved flame
proof canister. Keep a fully charged re extinguisher at hand. Remove any fuels, oils,
paint, pressurized spray cans, and chemicals from the weld area. Make sure any smoke/re
detectors are function properly. Do not weld on tanks, drums or barrels, especially if pres-
surized or sealed. Do not weld on any container that previously held fuel or chemicals.
Make sure the weld area is clear of flammable materials such as grass or wood shavings
solvents and fuels. Do not wear frayed or loose clothing. Visually inspect and recheck the
work area after welding looking for smoldering debris or flames.
WARNING! Welding gas cylinders are under high pressure. Keep all gas cylinders upright
and chained to a cart or held safely in a safety holding pen. Never transport gas cylinders
in an enclosed car van or other vehicle. Transport gas cylinders securely. Keep all cylin-
ders capped while not in use or during transport. Replace the cap on the cylinder when it
is going to be more than 24 hours before use. Do not use or attempt to repair faulty regu-
lators. Never weld on gas cylinders. Keep gas cylinders away from direct sparks.

6
Safety Warnings, Dangers, Cautions and Instructions
DANGER! Welding and cutting operations pose serious inhalation hazards. Some of these
hazards are immediate while others are cumulative in their effect. Do not weld in enclosed
spaces or in areas without adequate ventilation. Fumes and gases released in the welding
and cutting operations can be toxic. Use fans or respiration equipment to insure adequate
ventilation if you are welding in a shop or garage area. Do not weld on galvanized metal
under any circumstance. You may develop metal fume fever. Symptoms are similar to lu-
like symptoms. Seek medical advice and treatment if you are exposed to galvanized weld-
ing fumes.
If you experience any eye burning, nose or throat irritation while welding, these are signs
that you need more ventilation.
If you feel these symptoms:
• Stop work immediately and relocate work area with better ventilation.
• Wash and clean your face and hands.
• Stop work completely and seek medical help if irritation persists
DANGER! Never use brake cleaner or any chlorinated solvent to clean or degrease metal
scheduled to be welded or other related equipment in the area being welded. The heating
of this cleaner and its residue will create highly toxic phosgene gas. Small amounts of
this vapor are harmful and can lead to organ failure and death. If degreasing of a part is
necessary, use Acetone or an approved pre-weld cleaner. Use the proper personal protec-
tive equipment (PPE) when handling any cleaners/solvents.
DANGER! People with pacemakers should consult a physician and pacemaker manufactur-
er before welding. There is a potential for damage or serious malfunction resulting in
death. High Frequency energy (HF)/Electromagnetic Fields generated during welding can
interfere with pacemaker signals, even permanently damaging it. Some pacemakers offer
some shielding, but restrictions regarding amperage and HF starting of TIG arcs may be
placed upon the individual. Warn all potential bystanders that they should exit the work
area if they have a pacemaker or similar medical equipment before welding. Severe electri-
cal shock leading to injury or death may occur while using the plasma cutter if the user
becomes part of the circuit path. While the Amp output of the plasma cutter is limited, the
unit may produce an OCV of 300V or greater. Consult with a Physician if a pacemaker is
expected to be implanted.
DANGER! Never defeat or modify any safety guards or shields. Keep all safety covers and
shields in place.
Never place your ngers in or near a fan shroud or insert any object into the fan(s).
DANGER! Always switch the Foot Pedal/Transmitter to the off position when not in use or
when storing. Accidental activation may cause severe shock, arc flashing, burns or other
injury or damage. This will also help to preserve the battery and keep it charged.

7
Safety Warnings, Dangers, Cautions and Instructions
CAUTION! Trip Hazards exist around welders. Cords, cables, welding leads and hoses pose
a trip hazard. Be aware of their location and inform others of their location. Tape and se-
cure them so they will stay out of high trafc areas.
CAUTION! Welded metal can stay hot long after welding is completed. Burns may occur.
Always wear gloves or use tongs/pliers when handling welded or cut metal. Remember
the heat from the metal may catch other material on re. Always have a re-proof area
ready to place welded components until they fully cool. Use soap stone or a metal marking
marker to label the metal as “HOT” to serve as a reminder to all present in the area.
CAUTION! Welding and cutting operations generate high levels of ultraviolet (UV) radiation
which can burn and damage skin and eyes. The intensity is so high that exposed skin and
eyes can burn in a few minutes of exposure. Minimize direct skin and eye exposure to this
intense form of radiation by using proper PPE and sun screen where appropriate.
CAUTION! Do not allow bystanders. Do not allow others without proper Personal Protec-
tion Equipment (PPE) suitable for welding to stand in the welding area or to observe weld-
ing and welding related activities. If protection is not readily available, use a welding
screen to separate the welding area from the rest of the area. If no protection or screen is
available, physically exclude them from the welding area by a wall or other solid divider.
Keep all pets and young children away from the welding area.
IMPORTANT! This is an electronic device, which when properly designed may still occa-
sionally cause undesirable interference. Electromagnetic Fields can be generated by this
welding equipment and radiate into the work place which may disturb normal operation of
other electronic devices. Keep pedal stored properly with the switch turned to off to pre-
vent accidental transmission. If any electrical interferences is observed, discontinue use
immediately and consult a qualied electrician or electronics expert to help isolate and
remedy the cause of the problem by repositioning the receiver, or adding distance between
the transmitter (pedal) and receiver (dongle). If notied by the FCC that this unit is causing
electrical interference, you must discontinue use immediately.
DANGER! Never touch connectors or ttings while this is connected to the welder and
turned on. When storing the pedal, make sure the switch on the pedal is turned to off.

8
Specifications
Pedal Parameters and Specifications
Specication Receiver Dongle Foot Pedal and Transmitter
Power Type Adapter Input 100-240V 50/60Hz; .5A Adapter Output: 12V, 1A Lithium Ion Rechargeable Pack
Weight .78 lbs. 6.0 lbs.
Size 3.3”Lx3.3”Wx1.3”H12”Lx7.9”Wx 4.1”H
Rated Operation Distance Up to 100 ft. Up to 100 ft
Number of pedals supported in one location Up to 50 units Up to 50 Units
Expected Charging Cycles of Battery* Not Applicable. Dongle is powered by wall power. Up to 300
Charge Duration** NA 40 Days (8 Hour Shift)
Operation Frequency 2.4 Ghz 2.4 Ghz
Antenna Location Internal Internal
Recommended Operation Temperature*** 14°F to 140°F /-10°C to 60°C 14°F to 140°F /-10°C to 60°C
Warranty 18 Months 18 Months
*The stated charging cycles are expected charging cycles based on lab and industry testing. Ultimately it depends upon battery storage, and operation
temperatures and charging conditions. Extreme temperatures may reduce battery charging cycles that can be obtained. Improper battery cyling and
charging techniques may also reduce battery life. This unit uses Lithium ion type batteries, and has the typical requirements of Lithium ion batteries.
**The duration of a single charge of the battery may vary depending upon actual use. The charge duration is based off of an average useage and ex-
pected time on of the foot pedal. Leaving foot pedal switched on in storage or while not in use will drain battery.
Model Compatibility For The NOVA Wireless Pedal
Adapter/Pedal Part # TO FIT FOLLOWING MODEL NUMBER(S) / PART NUMBER(S)*
NVA-WL-FP200-AH07 AHP® and NOVA® 7Pin Alpha TIG 200X, 201XD, 225Xi, and 203XD with 7 Pins
P/N: AHP-FP22NWI
NVA-WL-FP200-EB08A ESAB® FirePower© Thermal Arc® 8 Pin (NOT FOR PEDAL WITH SWITCH)
P/N: 10-4015, 10-4016, 600285, 1442-0025
NVA-WL-FP200-EB08B ESAB (Rebel ™ EMP 205ic AC/DC, EMP 215ic, EMP 235ic)
P/N: W4014450
NVA-WL-FP200-EV07 Everlast® and NOVA® 7 Pin, Large, 22k and 47K. PowerTIG, PowerPro, PowerARC (models that are foot pedal
capable only), PowerUltra, UltraARC. Some MTS with large 7 pin connection (verify size before purchasing)
P/N: EV/NVA-FP22NWI, EV-FP50DL, EV-FP22DL
NVA-WL-FP200-EV07MTS Everlast® and NOVA® 7 Pin, Small. MTS models, small connector (verify before purchase) Does not t old MTS
160/200S.
P/N: EV/NVA-FP22NWI-MTS, EV-FP47DL-MTS
NVA-WL-FP200-LN06 Lincoln® 6 Pin
P/N: K870
NVA-WL-FP200-ML14 Miller® Hobart® 14 Pin Standard
Model: RFCS-14 and RFCS-14HD P/N : 043554, 194744
NVA-WL-FP200-ML06 Miller® 6 Pin (Maxstar 161STL, 161STH, Multimatic 200)
Model: RFCS-6M P/N: 195183 and 195504
Others Call to Inquire. Specications and availability subject to change.
*Disclaimer: NOVA is an independent brand and is not endorsed, guaranteed by, or manufactured by Miller, Lincoln or ESAB. All brand names are trademarked and mentioned are for selection purposes only.

9
!
Setup Guide
COMPONENT ID
FOOT PEDAL
TRANSMITTER
AND BATTERY PACK
CHARGING PORT
PEDAL ON/OFF SWITCH
BATTERY TO TRANSMITTER
CONNECTORS
CHARGER FOR PEDAL
CHARGING LIGHT
RED (CHARGING)
GREEN (CHARGED
CHARGING PORT CONNECTOR
CONTROL ADAPTER FROM DONGLE CONNECTOR TO WELDER
(TYPE VARIES BY BRAND, NOT NEEDED FOR SOME APPLICATIONS)
100-240V POWER PLUG
FOR DONGLE
DONGLE CONNECTOR
DONGLE/RECEIVER

10
NOTICE:
The foot pedal may arrive with the top separated from the bottom. This is not damage. To install the
top, flip the pedal spring under the cover to the forward position (towards transmitter end). Align the
spring loaded pivot pins with the corresponding holes in the pedal top. The pins are spring loaded
and can be squeezed so that the top slides down onto the pins. The pins will pop out into the holes
and allow the top to pivot once the pins and holes are properly aligned. If resistance is felt or the pe-
dal does not want to go together, you may need to make sure the pressure return spring is flipped so
that it pushes back against the pedal as it is assembled. There will be moderate resistance as the pe-
dal goes together, but it should be a rm, evenly felt resistance. Similarly, the foot pedal may be dis-
assembled for adjustment by simply by pressing in on the ends of the pins with a dull awl, or Phillips
type screw driver on both sides to remove the top. Once both pins have been pressed in, the pedal
top should pop up for access to the foot pedal switch travel adjustment and other parts.
Setup Guide
Push in on left and right side pivot pins to remove or
seat cover. Pins should pop through corresponding
holes in the cover when seated properly.

11
Setup Guide
Getting Started
UNPACK YOUR UNIT.
Upon arrival, you will need to completely unpack your foot pedal, and
test it. It is important to identify any potential issues with your pedal.
If any issue is noted, you should contact NOVA and resolve it imme-
diately. The pedal is well packaged, but shipping damage can occur.
You should have the following in your box:
1. Wireless foot pedal with built-in transmitter.
2. Charger for pedal.
3. Receiver dongle (Machine side) with magnetic backing.
4. Adapter plug for the dongle to t welder brand (exact adapter
varies by brand) Not needed for Everlast MTS products.
When you receive your package, inspect the unit for damage. Check
for the presence and general condition of the parts. Some slight rub-
bing or chafng of some parts may be present, but this is considered
normal. If any item is damaged or missing, please inform NOVA with-
in 72 hours of product receipt. NOTICE: Shipping damage claims
after 30 days may not be accepted unless extenuating circumstances
exist such as overseas deployment, etc.
DESCRIPTION AND GENERAL OPERATION.
The NOVA Wireless pedal has been designed to operate on a com-
mon 2.4 Ghz wireless design which allows the pedal to be operated
in an environment where multiple wireless NOVA pedals may be
present. The design is aimed at preventing cross-talk between multi-
ple units and accidental activation of the arc from another pedal. Long
life Lithium-type batteries are used in the transmitter located in the
pedal. These batteries are rechargeable and can be recharged up to
300 times or more. Each charge of the battery is capable of lasting
up to 40 days on normal 8 hour shifts. The pedal is capable of oper-
ating and controlling the welder up to 100 feet away from the receiver
mounted on the welder.
The pedal is used to both start the arc and incrementally control the
up and down ramping of the Amperage from minimum to maximum
selected Amperage. The maximum Amp output is governed by the
maximum Amp setting selected by the user on the welder control
panel. Minimum start setting is governed by the welder default or
start setting selected by the user.
PAIRING OF PEDAL AND RECIEVER.
The pedal arrives already paired (synchronized) to the receiver from
the factory. There is no need to pair the pedal again unless a repair
or replacement of the pedal or receiver has been done. The pedal
can be paired again however in the event the pairing is lost.
Use the following directions only if pairing has been lost:
1. With the foot pedal switched to off, and the dongle/receiver
disconnected from welder, connect the dongle/receiver to power
source. (NOTE: The dongle does not need to be disassembled
in this process.)
2. Disconnect all other receivers (dongles) in use in the facility.
3. Access the transmitter board depicted below by removing the 4
screws on the cover of the transmitter box located on the front
of the foot pedal. (Do not remove board from pedal housing.)
4. Orient the board as shown to nd the button(1) and the LED (2)
5. With the receiver on, press the button 1. The small LED (2)
will light and should stay on constantly for a few moments.
6. The LED should begin to blink when the pairing link has been
made. When the LED begins to blink, press button 1 again.
7. Press down on the foot pedal fully to complete the pairing.
8. Replace transmitter cover and check for proper operation.
1
2
3
4
NOVA Wireless Pedal Contents
LED
1
2
NOTICE:
When the welder is set to high Amperages, the pedal will become
more sensitive to Amperage change due to the change of ratio be-
tween the xed pedal travel length and the Amp range it is required
to control. When set to high maximum Amp settings, ne Amp con-
trol may be more difcult to achieve and the unit may seem to
“accelerate” throughout the Amp range very quickly. When set to a
very low maximum Amp setting, by comparison, the pedal will re-
quire more movement to make signicant changes in Amperage and
the rise and fall of Amperage will change more slowly throughout the
range. At low maximum Amp settings, greater movement of the
pedal may be required for a stable arc start at low Amps if starting
Amperage is at or below the threshold of the Tungsten size used.
This is not a pedal fault or flaw. It’s the limitation of welding at low
maximum Amp settings and incorrect Tungsten size.

12
Setup Guide
Getting Started
CONNECT THE BATTERY WIRE.
The pedal is purposefully shipped with the wires from the lithium ion
battery in the pedal to the transmitter disconnected for safety and to
preserve the initial charge on the battery.
To Connect the Battery to the Transmitter:
• Match up the connector ends by pairing up the tabs on the
connector and slide them fully together.
• Tuck the wire down beside the transmitter.
• Do not leave the wires or the connectors sticking out. The gap
beside the transmitter allows room for both the wire and con-
nectors to be pushed down beside the transmitter.
CHARGE THE BATTERY
The battery carries a charge from the factory that was used to pair the
transmitter and receiver. However, before use, the battery should be
charged. Each charge can last up to 40 days between charges with
average use on 8 hour shifts. If the pedal acts irregularly, or the
Dongle/Receiver indicates a low battery charge recharge the battery.
To Recharge the Battery:
• Set the transmitter toggle switch on the front of the pedal to the
“OFF” position. (See Foot Pedal/Transmitter Assembly Diagram.)
• Locate the charger in the packaging. (See Foot Pedal Charger
Diagram.)
• Connect the charger to the charging port on the front of the
pedal.
• Plug the charger into a suitable 120V (100-240V permissible)
receptacle.
• The LED light at the bottom of the charger will turn red.
• Charge for at least 4 hours until the LED turns from red to
green.
• Once the LED turns green, remove the charger.
• Keep the pedal switched to “OFF” until the pedal is ready for
use. Remember to turn the switch to “OFF” position when not
in use or when stored to preserve battery life and prevent acci-
dental operation of the pedal.
CONNECT THE RECEIVER DONGLE TO WELDER.
The Receiver/Dongle assembly requires 100-240V power to operate.
In the North American Market, this will typically be used with a stand-
ard NEMA 5-15 120V outlet. The Dongle may be powered with an
IMPORTANT!
Charge the pedal only when the toggle switch is placed in the off
position. Do not use the pedal with the charger connected. Keep
the pedal stored with the switch in the “OFF” position to prevent
discharge of the batteries. As a “best practice” switch the pedal
switch to the “OFF” position whenever the pedal is not be used or
left unattended to prevent accidental arcing.
FOOT PEDAL CHARGER (100-240V)
Foot Pedal Charger (100V-240V)
Red/Green LED
Connect To Pedal
FOOT PEDAL /TRANSMITTER ASSEMBLY
Connect charger here to charge pedal.
Connect Wires.
ON/OFF
Transmitter Toggle Switch
DANGER!
When left unattended, when work is completed, or when the pedal
is otherwise not being used for welding purposes such as in trans-
porting or carrying, turn the pedal/transmitter switch to the “OFF”
position to prevent accidental activation. Shock, burn, arc flashing
and/or injury could result from accidental activation of the pedal.
Damage to high value parts may result as well if torch is left on
work and the pedal is accidentally activated and an arc starts.

13
Setup Guide
Getting Started
extension cord if the outlet is not near the welder, but be mindful that
there is an additional trip hazard.
To connect the Dongle:
• Turn on welder power.
• Switch the Foot Pedal/Transmitter to “OFF”.
• Locate a magnetic surface on the welder or nearby work surface
and attach the Dongle via the hidden magnet located on the
back side of the dongle housing.
• Locate the correct Dongle Adapter and connect it to the Dongle
connector.
• Connect Dongle to machine control/remote terminal of the weld-
er. (This is the normal location for the foot pedal or remote.)
• Plug Dongle into the power source (100 to 240V). The “On” LED
should be lit. North American standard is 120V, NEMA 5-15R
• Switch the Foot Pedal/Transmitter to “ON”.
• The NOVA Wireless pedal is now ready for use.
OPERATION OF THE NOVA WIRELESS PEDAL.
The NOVA wireless pedal operates simply and accurately. It is already
paired with the receiver so it is ready to go when connected and
turned on. The wireless nature of the pedal means that the pedal
operates best by line of site. Large obstructions, walls, and signi-
cant metal structures in the path of transmission will likely interfere
with pedal operation. After charging initially, and following the
“Getting Started” directions in the previous information, the pedal will
be ready for use.
To operate the wire less pedal:
• Conrm the welder is turned on.
• Conrm the dongle is plugged in and receiving power.
• Conrm the foot pedal has been switched on.
• Select the “Pedal” function of your welder, or appropriate setting
that you would use with your welder when using a foot pedal.
• Select the maximum Amperage you wish to use with the pedal.
• Set your welder normally as you would with any foot pedal,
including start settings, tungsten diameter etc. for best starts.
• Press lightly on the pedal until you hear/feel a slight click. This
will start the arc. Pressing further down will increase the Amper-
age. Raising the pedal will decrease the Amperage. You can
continue to modulate the Amperage throughout the entire range
by varying the pedal position.
• To stop the arc, smoothly raise your foot off the pedal so that it
completely goes back to the pre-start position.
• If you maintain pressure on the pedal, the arc will not terminate
until the pedal is fully released back to the pre-start position.
There are a couple of additional pieces of information that will help
you to understand the function of the pedal, transmitter, and receiver.
• The Dongle includes 3 LED lights. See diagram, next page.
• The top green LED (1) indicates the dongle is receiving power.
• The middle LED (2) will light and flash red as the pedal is in
use. (This is used as a diagnostic to conrm the dongle is re-
ceiving signal as well when the pedal is pressed.)
• The bottom LED (3) will light if the Dongle senses a weak bat-
tery. If this happens stop and charge the battery on the foot
pedal/transmitter as soon as possible. Do not attempt to com-
pletely run down the battery or battery life will be shortened.
• The Dongle must have a power source. It is not battery operat-
ed. It can be powered by voltage ranging from 100V-240V.
• Unplug the Dongle when not in use. The Dongle does not have
an ON/OFF switch.
DONGLE RECEIVER CONNECTOR
DONGLE ADAPTER
DONGLE/RECEIVER
(MAGNETIC)
DONGLE POWER PLUG

14
Setup Guide
Getting Started
• Not all units require an adapter. If the supplied adapter does not
t your welder, contact NOVA as soon as possible. Not all weld-
ers can be used with the NOVA wireless pedal. Older, non digi-
talized welders will often not be able to work with this unit. If in
doubt, consult the NOVA product compatibility information on
the specications page, or contact NOVA directly before pur-
chase.
100-240V Dongle/Receiver
DONGLE CONNECTOR
DONGLE/RECEIVER
DONGLE POWER PLUG
1
2
3

15
Setup Guide
Troubleshooting
Trouble Cause/Solution
Welder does not respond when pedal is activated Battery charge is too low. Check Dongle indicator, Recharge battery.
Dongle is not plugged in. Plug in Dongle.
Foot pedal transmitter is switched off. Turn switch on
Battery to transmitter wires are unplugged, Plug wires into each other .
Wrong mode selected on welder. Set to proper mode such as “Pedal”.
Welder reacts sluggishly or irregularly and arc
lights irregularly or is delayed
Battery charge is low. Check Dongle indicator. Recharge battery.
Obstruction. Remove obstruction. Operate line-of-sight.
Too far away from receiver. Move closer.
Arc is shut off suddenly and reinitates. HF point gap (if used) is incorrect, or HF starting device is emitting too much
High Frequency at start.
Arc does not shut off cleanly or properly Improper machine settings. Turn off down slope.
Pedal is not fully back to stop. Press on rear of pedal to make sure the pedal
is in the fully up position and the micro switch is not being activated.
Microswitch is out of adjustment. Remove cover and make sure microswitch
is adjusted so that there is no contact when pedal top and the microswitch
when in fully up position.
Arc cuts out or doesn’t seem stable as pedal is
swept up or down. Response is not as expected.
(Wired pedal operates normally.)
Interference. Turn off all other electronics in shop one at a time to isolate.
Bad potentiometer or broken internal wires on the pedal. Contact NOVA
Another foot pedal is controlling the welder. Foot pedal has been improperly paired, or lost pairing. This should not nor-
mally happen unless the pedal has been worked on or replaced. Follow re-
pairing instructions in this manual. Contact NOVA.
If another brand, is interfering, discontinue use of the other pedal and contact
NOVA.