Novita A5 Operator's manual

Ensure that the power plug is disconnected from the power supply at all

times during installation, maintenance and transportation.

• DO NOT operate the unit without filter unit installed. Please remove the plastic

packaging on the filter unit and insert them in the correct sequence before use.

QUICK STARTER GUIDE

A5.

AIR PURIFIER

SCAN THE QR CODE

to view the user manual

for full operating instructions

novita.com.sg

• SETTING UP

01. Remove all packaging materials and place the unit on a dry, stable and level surface.

02. Grasp both recess sides of the air inlet panel and pull outwards to remove it from the unit.

03. Remove the plastic packaging on the 3-in-1 PuriPRO®filter and place it into the unit with granular activated

carbon filter as the outermost layer while H13 HEPA filter as the innermost layer.

04. Align the air inlet panel upper middle latch to the designated catch on the unit’s internal housing.

Press both the upper left and right corners followed by both the bottom left and right corners of

the air inlet panel to lock and secure it in position.

05. Ensure there is a clearance of at least 50 cm for the air inlet and clearance of at least 10 cm for the air outlet.

• Ensure the tag on the PuriPRO®filter is facing the filter cover.

• Ensure the PuriPRO®filter unit is properly assembled and installed in position before usage.

• DO NOT block the air inlet and air outlet to ensure sufficient air ventilation and maximum efficiency of the unit.

• OPERATING NOTES

Insert the power plug into the power supply and power on. Unit beeps once and the display screen illuminates and flashes once. At Off Mode, the POWER

ON/OFF button illuminates in red.

STANDBY MODE

01.

POWER ON/OFF

Touch the POWER ON/OFF button to switch on the unit. Unit operates in auto mode with air quality light indicator illuminating in green by default.

02.

FAN SPEED

Touch the SPEED button to select auto mode, speed 1, 2, 3 or sleep mode. Its corresponding light indicator illuminates on the selected setting.

04.

• When the unit is left idle for 3 seconds, it will auto resume sleep mode function.

• At sleep mode, when childlock function is activated, the display screen will prompt “LOC” whenever the user touches the control panel. To deactivate the childlock function,

touch and hold the POWER ON/OFF and SPEED buttons position for 3 seconds.

SLEEP MODE

Touch the SPEED button consecutively to select sleep mode. Upon activation, display screen will prompt “SLP” and its corresponding light indicator

illuminates. At sleep mode, air flow is reduced to the lowest and after 5 seconds, all light indicators will be turned off for an undisturbed rest.

To wake the unit, touch any button on the control panel. When the light indicators illuminate (3 seconds), touch SPEED button to exit sleep mode.

06.

AUTO MODE

Touch the SPEED button consecutively to select auto mode. Upon activation, its corresponding light indicator A illuminates. At auto mode, the fan

speed setting will automatically adjust in accordance to the air quality detected.

05.

Air Quality Indication

Fan Speed Setting Speed 1 Speed 2

Excellent Good

Speed 3

Poor

Air Quality Light Blue Green Red

PM2.5 SENSOR INITIALIZATION

Once completed, the moving average FIR PM 2.5 readings (unit: µg/m³) will be reflected on the display screen and the air quality sensor light indicator will illuminate

in different colours, in accordance to the air quality detected.

• The FIR PM2.5 Particle Sensor detection accuracy is subjected to a yearly depreciation rate of 10% to 20%. For optimum air quality detection, it is recommended

to perform factory calibration to the air quality sensor once every 2 years.

03. The FIR PM2.5 Particle Sensor will take 10 seconds for initialization. During the initializing process, the PM2.5 display will show “ – “ and loop in a clockwise direction

with air quality sensor light indicator illuminating in green.

UNIT DISPLAY SCREEN

• While operating the unit, in the event if there is any power trip, the unit will auto resume its operation based on the last preceding setting, when the power is restored.

“CLICK”

Latch

Catch

CHILDLOCK

Touch and hold both POWER ON/OFF and SPEED buttons for 3 seconds to activate childlock function and display screen will prompt “LOC”. Upon activation,

the control panel will be locked and display screen prompts “LOC” whenever user touches the control panel. To unlock, touch and hold both POWER ON/OFF and

SPEED buttons for 3 seconds.

07.

• CLEANING & MAINTENANCE

• Please turn OFF and disconnect the power plug before cleaning and maintenance.

• Please refer to the operating instructions manual for full cleaning & maintenance instructions.

For external maintenance, use a damp cloth or mild cleansing detergent to wipe the surface to prevent accumulation of dust regularly. It is recommended to clean and

maintain the Washable Mesh Filter once every 2 weeks (approx. 500 hours).

09. Touch the TIMER button consecutively to select your preferred timer operation (from 0 to 8 hours) to switch off the unit. Timer can be set at an interval of 1 hour.

The selected timer operation will be displayed on the display screen for a few seconds before resuming the PM2.5 reading display. When timer function is activated,

its corresponding light indicator illuminates. To deactivate timer function, touch and hold the TIMER button for 2 seconds and its corresponding indicator

stops illuminating.

TIMER

11. By default, anion mode is activated with unit operation.

ANION MODE

Grasp both recess sides of the air inlet panel

and pull outwards to remove it from the unit.

Remove the exhausted 3-In-1 PuriPRO®

Filter.

Remove the plastic packaging on the 3-In-1

PuriPRO®Filter. Assemble the filter with granular

activated carbon filter as the outermost layer

while H13 HEPA filter as the innermost layer.

2Install

New Filter

FILTER TIMER MASTER RESET FOR PREMATURE FILTER REPLACEMENT

In the event of premature filter replacement,

touch and hold both the TIMER and the

SPEED buttons concurrently for 3 seconds

to do a filter timer master reset. Unit beeps

once and auto turn off to notify user that the

master reset is completed.

STANDARD FILTER TIMER RESET

Touch and hold the button for 3

seconds to reset filter lifespan. Unit

beeps once with Filter Replacement

Indicator stops illuminating to notify user

that the filter timer has been reset

successfully.

10. Touch and hold the TIMER button for 3 seconds and unit beeps thrice to activate the 12 hours operation cycle. Under this mode, unit is programmed to operate

based on 12-hour ON; 12-hour OFF routine cycle.

12-HOUR OPERATION CYCLE

• To deactivate this function, touch and hold TIMER button for 3 seconds, unit beeps thrice.

• Upon activation of the 12-Hour Operation Cycle, the normal timer setting function will be disabled.

• 24 MONTHS/6,000 HOURS* 3-IN-1 PURIPRO®FILTER REPLACEMENT

• Remove the plastic packaging on the 3-In-1 PuriPRO®Filter before use.

• DO NOT use any detergents, solvents or aggressive agents to clean the Filter unless specified.

When the PuriPRO®Filter lifespan is left with 0 hour, the Filter Replacement Indicator slow flash once every 3 minutes as a

reminder for filter replacement. In the event when the filter is not replaced after 10 days, the Filter Replacement Indicator will fast

flash once every 30 seconds and unit can only operate at fan speed 1 as a safety feature to protect the fan motor. All other modes and

fan speed setting will be deactivated. Please replace with a new set of PuriPRO®Filter in accordance to its stipulated replacement

period for optimum purification performance.

* Based on average 8 hours a day, 7 days week usage under domestic indoor environment.

08. Touch and hold the SPEED buttons for 3 seconds to turn off all light indicators while fan speed setting continues to operate as per preceding setting. Touch any

button on the control panel to resume the light indicators illumination.

TO SWITCH OFF LIGHT INDICATORS

Old

Filter

Old

Filter

Remove

Old Filter

Remove

Filter Cover

New

Filter