Novus NVC-125B User manual

USER`S MANUAL VER. 1.0
B/W CAMERA
NVC-125B
NOVUS SECURITY Sp. z o.o.
359 Pulawska Str., 02-801 Warsaw, Poland
tel: [phone]; fax: [phone]
[email protected]; www.novuscctv.com
© Copyright 2003, NOVUS SECURITY Sp. z o.o.

1. SIDE VIEW
1) Auto Iris Lens (option)
This is the lens used with the camera (optional item)
2) Flange-Back Adjusting Ring
A screw is provided to fix the lens mount.
3) Camera Mounting Screw Hole
Mounting base for installing the camera.
4) Auto Iris Lens Connector
This connector supplies power and video or DC control
Signals needed to control the auto iris lens.
5) Auto iris lens control cable
MAJOR COMPONENTS & FUNCTION
* DO NOT PLACE THIS PRODUCT UNDER EXTREME TEMPERATURES
(SUITABLE TEMP RANGE: 0˚C~40˚C)
* DO NOT USE THIS PRODUCT NEAR WATER OR MOISTURE.
* DO NOT USE LIQUID CLEANERS OR AEROSOL CLEANERS.
* DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND,
OR TABLE.
2)Flange-back Adjusting Ring
5)Auto Iris Control Cable
1)Auto Iris Lens
3)Camera Mounting Screw Hole
4)Auto Iris Lens Connector
(SIDE VIEW)
NVC-125B B/W Camera user`s manual. Version 1.0
2
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

2. REAR VIEW
1) Lens Select Switch
When using an auto iris lens, set the switch according to the lens type.
VIDEO : Set to this position when using a Video type to the lens.
DC : Set to this position when using a DC (galvanometric) type lens.
2) EE/AI Selection
When using the manual lens, the brightness of the picture image will be
fixed by setting EE mode, as the shutter speed is automatically varied
in the range of 1/50 to 1/100,000 sec according to the incident light.
Set the Al when using the VIDEO type or DC type auto iris lenses.
3) Video Output Connector
BNC connector that outputs a composite video signal.
4) Lens Connector
When using an auto iris lens, connect the lens cable to this connector.
5) Power Input Terminal
Connect to a AC24V power source. When operating with an AC24V
power Supply, use only an isolated power source. (Be sure not to
connect the power source until all other connections are completed.)
6) BLC On/Off
Back Light Compensation Switch.
7) DC Iris Level Volume
Adjusting the brightness of picture when using the DC type auto iris
lens.
8) Vertical Phase Adjuster
If the Sync Selection switch is set to the Line Lock ON mode, this
potentiometer can be adjusted to synchronize this camera the other
in a system.
NVC-125B B/W Camera user`s manual. Version 1.0
3
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

Connect the video output of the camera to the video
Input of a monitor or other equipment. When using a “loop through”
connection of
two or more monitors, set the 752KPswitch of only the final monitor to on.
Determine the type of cable according to the distance of the connected
equipment.
CONNECTING CABLE
(REAR VIEW)
*Do not turn any component’s power on until all connections are completed.
NVC-125B B/W Camera user`s manual. Version 1.0
4
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

When using an auto iris lens, install the lens plug on to the lens cable as
follows.
1. Cut the iris control cable at the edge of lens connector to remove the
the incompatible lens connector and the outer cable cover.
INSTALLING AUTO IRIS LENS CONNECTOR
Iris Control Cable 5/6” (Approximately 8mm)
1/4” (Approximately 6mm)
2. Four covered wires will be exposed after removing the cover of the
iris control cable.
Removing the insulation of the individual iris control wires leaving
approximately 6mm.
3. Video type lens
Set lens switch to VIDEO.
Connect the lens cable of the video type lens.
If the plug on the cable is of a different type, replace it with the provided
4-pin iris plug.
4. DC iris Lens
Set lens switch to DC
Connect the lens cable of the galvanometric
type lens.
If the plug on the cable is of a different type,
replace it with the provided 4-pin iris plug.
pin1
pin3 Rib
pin2
pin4
NVC-125B B/W Camera user`s manual. Version 1.0
5
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

5. Connector Cover
Push together the connector cover and connector base to interlock.
Lens Connector Base
Iris Control Cable
Connector Cover
Auto Iris Lens
DIMENSION6
GNDGND4
Video SignalDrive(+)3
Not UsedDamp(+)2
Power(+9V)Damp(-)1
Video Control
Type
DC Control
Type
Pin No
Pin Arrangement
133
NVC-125B B/W Camera user`s manual. Version 1.0
6
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

SPECIFICATIONS
Under 90% Non-condensingStorage Humidity
Under 95% Non-condensingOperating Humidity
Flicker less on/off , Backlight compensation on/off
AGC on/off , Gamma 0.45/1.0
Auto White Balance for indoor/outdoor
Dip Switch Control
Video output : BNC (rear) / Al Lens : 4-PIN DIN (rear)Output Sockets
Power
Power Consumption
Input Voltage
Video / DCAuto Iris Lens
CRUCSLens Mount
0.45Gamma
45 dB or more (AGC off)Signal to Noise Ratio 1/50 ~ 1/100,000 s Auto
Auto-Iris
Light sensitivity – 30 IRE/[)
1Vp-p composite video into 752KP
Video Output signal
Internal / line-lockSynchronization
625 lines interlaced
Scanning System
1/3” Interline SONY SUPER HAD CCDPick-up device
570TV LinesHorizontal resolution
CCIR
Signal Format
MODEL19&%
CONTENTS OF THE PACKAGE
2 Screws
Mount adaptor
User guide
Auto Iris Lens Connector
L-Wrench
Weight
58 x 53 x 133mmDimension 350 gr
MAX 4.5W
DC 12V / AC 24V
3 PIN TERMINAL
NVC-125B B/W Camera user`s manual. Version 1.0
7
© Copyright 2003, Novus Security Sp. z o.o. All rights reserved.

All rights reserved © NOVUS SECURITY
NOVUS SECURITY Sp. z o.o.