NSK Control S 9402A User manual

PROART DUAL AM/FM TUNER WITH RS232www.altronics.com.au
Manufactured in China for Altronic Distributors Pty Ltd
VIDEO DOOR INTERCOM
S 9402A Base Station & Camera System
S 9403A Additional Base Station
S 9404A Additional Camera Unit
OPERATING INSTRUCTIONS

VIDEO DOOR INTERCOM SYSTEM
Page 2
Included in the box:
• Indoor base station x 1
• Outdoor camera x 1
• Mounting bracket x 1
• Mounting screws (4Gx18mm) x 2
• Power supply
Overview
An ultra modern and stylish video intercom system featuring a colour 3.5” TFT LCD screen on the base
unit. The all-weather, vandal resistant, cast aluminium door station features a LED for night time
illumination. The hands-free LCD base unit enables intercom, surveillance and activation of door release
solenoids. The system may be expanded to include four LCD screens and two outdoor camera units for
use in homes with multiple entrances. If multiple base units are installed they may be used as an internal
home intercom system. S 9402A system includes 1 x LCD base unit, 1 x door camera unit. For installations
requiring 2 indoor or 2 outdoor stations, the additional part numbers of S 9403A and S 9404A must be
ordered as they contain junction boxes for correct operation.
Features
• Colour 3.5” LCD screen
• Hands free operation
• Modern, slimline design
• Two selectable chimes
• Intercom, surveillance and door release functions
• Up to four base units may be used together
• Rugged, all-weather vandal resistant camera unit
• White LED illumination on camera unit
• 2 cameras may be used on separate entry points
• 4-wire connection
• Includes power supplies
Installation
1. Determine the mounting locations for both outdoor camera and base station. To ensure people are
within view when the camera is mounted, bear in mind the camera’s 55 degree viewing angle. Typical
wall mounting height 1450mm. Ensure you are satisfied with the viewing position of the camera and
base station before drilling any holes in your wall.
2. At the selected base station mounting location, attach the mounting bracket to the wall securely using
the template and hardware provided. In the centre of the bracket, drill a hole for the electrical and
camera signal wiring.
3. Connect the wiring between the base station and camera as per figure 3.
4. Slide the base station down against the mounting bracket until the hooks on the bracket secure the unit
in place.
5. Switch on AC power to the unit.
6. Switch the on the base station (see figure 1 for location of on/off switch.)
Important mounting guidelines: Do not install the monitor and camera units where they will be exposed
to dirt, moisture, excessive humidity, temperature (+40°C) or constant direct sunlight. Do not select a loca-
tion where it will be exposed to vibration. Select a location close to an AC power outlet where it is easy to
view the screen and operate the monitor.
Installation With Two Indoor Base Stations
Follow the wiring diagram shown in figure 4. The second base station simply connects into the first base
station via the additional 4 way header terminal.

Page 7
VIDEO DOOR INTERCOM SYSTEM

VIDEO DOOR INTERCOM SYSTEM
Page 6
Troubleshooting
Problem Cause
No power (Power LED off) Insert power cord into power outlet. Ensure the ON/OFF
switch on the bottom of the unit is switched to ON.
Power LED dim Cabling between monitor and camera has a short circuit.
No picture Check the brightness and contrast controls. Ensure wires
are connected to the correct terminals, ie: 1 to 1, 2 to 2 etc.
Specifications
Max cabling distance: ..........................................................................................50m (22AWG, 0.65mm 4 core)
Base station
Monitor screen: ................................................................................................................................5.6” TFT LCD
Voltage requirements: ................................................................................................................................15V d.c.
Call tone: ............................................................................................................................2 tone xylophone tune
Operating temperature: ..........................................................................................................................0 to 30°C
Dimensions: .................................................................................................................. 250W x 180H x 38D mm
Weight:..............................................................................................................................................................1.2kg
Outdoor camera
Voltage requirements: ................................................................................................................................12V d.c.
Sensor:..................................................................................................................................................CCD Colour
Viewing angle: ....................................................................................................................................................68°
Operating temperature:........................................................................................................................-40 to 75°C
Dimensions: ......................................................................................................................55W x 104H x 38D mm
Weight:............................................................................................................................................................380gm
Optional Door
Lock Interface Box
Plugpack for
door strike
Doorstrike
To
Intercom
To
12VDC
To
Strike
- + - + - +
To Video
Door Intercom
Red + Black -
Fig 6. Optional door lock interface connection.
To Video Door Intercom
Camera Unit

VIDEO DOOR INTERCOM SYSTEM
Page 3
Connectorsat the back of monitor
5
6
7
1
2
3
4
5
6
7
1
2
3
4
MONITOR
11
11
22
22
33
33
44
44
PI N
SHUNT
CAMERA ELECTRI C
DOORLOCK
POW ER
SOURCE
INTERPHONE
(OPT I ON)
IMAGE MEMORY
(OPTI ON)
1
2
3
45
6
7
8
9
10
11 12 1314 15
18
17
16
Fig 1. Base Station.
1
2
3
4
5
Fig 2. Outdoor Camera Unit
1. Screen
2. Speaker
3. Microphone
4. Power LED
5. Intercom LED
6. Monitor button
7. Call button
8. Unlock button
9. Answer button
10. Volume level control
11. Bell ringing volume control
12. Colour adjustment
13. Contrast adjustment
14. Power ON/OFF switch
15. 15VDC Input
16. Not used
17. Camera connection
18. Additional base station connection
1. Camera
2. Microphone
3. Infra-Red LEDs
4. Speaker
5. Call button

VIDEO DOOR INTERCOM SYSTEM
Installation With Two Outdoor Cameras
This requires the use of the expansion junction box included with the S 9404A additional camera unit. The
junction box allows for a maximum of two indoor base stations and two outdoor camera units. See figure
5 for a wiring diagram of this system.
Operation
When installation is complete switch the power switch to the ON position. Adjust the volume level, bell
chime level, brightness and contrast as desired (you may have to unhook the unit from the wall bracket to
adjust some settings).
When a visitor presses the call button on the camera unit the monitor speaker sounds a chime tone. The
visitors image will appear on the screen. You may choose not to respond by not pressing the answer but-
ton, the visitors image will disappear within 30 seconds. To respond to a visitor you can press the answer
button and talk. The visitors image will remain on screen for 90 seconds or until you press the answer but-
ton again to hang up.
After speaking with the visitor, you may choose to open the door for them. To do this press the unlock
button. Note: You must have an electronic door strike installed in your system for this button to operate.
If you have two base stations installed in your sytem, you can press the call button to communicate with
the second location. This is ideal for two storey or larger homes as an internal intercom.
Optional Door Lock (Door Strike) Interface
To install door strike, select a 12V d.c. power supply with enough power (current) for your door strike. A
12V 1A d.c. plugpack such as the Altronics M 9274A should be suitable for most door strikes.
Drill cable entry hole in box containing PCB (PCB labelled ‘Altronics strike timer V1’). This box can be
located up to 20m from the door strike.
For connection information see Figure 6.
2
1
3
4
Camera
2
134
Base Station
2
1
3
4
2
1
3
4
5
6
7
Optional door
lock interface
Jumper
Fig 3. Basic wiring for single camera, single
base station configuration.
Page 4
See Fig. 6

VIDEO DOOR INTERCOM SYSTEM
Base Station 1
2
1
3
4
2
1
3
4
2
1
3
4
5
6
7
2
1
3
4
2
1
3
4
2
1
3
4
5
6
7
Base Station 2
V+
V-
1
2
3
4
V+
V-
1
2
3
4
V+
V- 1
2
3
4
V+ V-
1234
Expansion
Junctionbox
Camera 1
2
134
Camera 2
2
134
Jumper Jumper
Optional door
lock interface
Optional door
lock interface
Fig 5. Wiring for two indoor base stations and two outdoor
camera units. Ensure all wires go to the correct terminals
ie: 1 to 1, 2 to 2 and so on.
Camera
2
134
Base Station 1
2
1
3
4
2
1
3
4
2
1
3
4
5
6
7
2
1
3
4
2
1
3
4
2
1
3
4
5
6
7
Base Station 2
Optional door
lock interface
Jumper Jumper
Fig 4. Wiring for two indoor base stations to a
single outdoor camera unit.
Page 5
See Fig. 6
See Fig. 6
See Fig. 6

Page 8
VIDEO DOOR INTERCOM SYSTEM
For repair or service please contact your place of purchase. Note: Under no circumstances should you
attempt to repair the product yourself or via a non-authorised Altronics service centre as this will
invalidate the warranty! During the warranty period, we undertake to repair or replace your product at
no charge if found to be defective due to a manufacturing fault. The warranty excludes damage by mis-
use, neglect, shipping accident, incorrect installation or no fault found.
NOT FIELD SERVICEABLE.
Distributed by Altronic Distributors Pty. Ltd. Perth. Western Australia.
Phone: [phone] Fax: [phone] Internet: www.altronics.com.au