Nucu Sointu User manual

NucuSointu manual

Table of Contents
1) Contents of the package .......................................................................................... 3
2) Nucu control panel ................................................................................................... 4
3) Nucu startup mode................................................................................................... 5
4) How to use Nucu....................................................................................................... 6
5) Battery charging and operating time....................................................................... 8
6) Mobile playback........................................................................................................ 9
7) Adding sounds to Nucu audio library (windows pc) ............................................. 10
8) How to clean Nucu.................................................................................................. 11
9) Assembling the Nucu after cleaning ..................................................................... 13
10) Technical specifications ......................................................................................... 13
11) Support .................................................................................................................... 13

1) CONTENTS OF THE PACKAGE
Confirm that the following parts are included:
Nucu
Nucu base plate (inside the Nucu)
AC adapter
USB –Micro USB Cable
3.5mm AUX Cable
Note:
1. If any part is damaged, do not use it. Contact Nucu customer service:
•[email protected]
2. In hospital use check that the AC adapter has the "Approved Medical Device" notation

2) NUCU CONTROL PANEL

3) NUCU STARTUP MODE
In startup mode Nucu uses:
1. Syke (heartbeat) soundscape will be played
2. Volume is set to level 2
3. Repeat mode is set On
Nucu includes the following soundscapes:
1. Syke (hearbeat)
2. Sade (rain)
3. Nuku nuku nurmilintu (Nurmilintu song)

4) HOW TO USE NUCU
All Nucu functions are managed from the control panel. After setting the desired soundscape and
volume level, place the Nucu on a flat surface and put the baby in the nest. Observe how the baby
reacts to Nucu. Do not leave the baby unattended on the Nucu.
Note:
1. Control Panel goes into sleep mode in 30 seconds if no buttons are pressed. In sleep mode
buttons are not active. In sleep mode Volume and Battery level indicator lights turns off
2. Control Panel is activated for sleep mode by pressing power button once. When
activated Volume and Battery level indicator lights turn on
ACTIVE MODE
SLEEP MODE

Function
What to do
Button
Power On
Press Power button once. Nucu is
ready to use when Power indicator
light is on
Power Off
Press the Power button until the
power indicator light turns off (about
3 seconds)
Volume Up
Press Increase Volume button once.
Each press increases volume by 1
level
Volume Down
Press Decrease Volume button once.
Each press decreases volume by 1
level
Skip Backward
Press Previous Track button once
Skip Forward
Press Next Track button once
Repeat On / Off
Press Repeat button once. Repeat is
On when Repeat indicator light is On.
Repeat is Off when Repeat indicator
light is Off
Mobile Playback
See section 6) Mobile Playback
Adding sounds to audio
library
See section 7) Adding sounds to Nucu
audio library (Windows PC)
Note: Nucu will not turn off if it is connected to the computer via USB cable

5) BATTERY CHARGING AND OPERATING TIME
Battery is charged using a AC adapter and USB cable. Battery can be charged while the Nucu is in
use.
Steps:
1. Connect USB cable to the:
a) AC adapter’s USB port
b) Control panel’s Micro-USB port
2. Plug AC adapter to the wall outlet. Charging the empty battery takes approximately 10 hours.
Note: The full battery lasts approximately 19 hours in use.

6) MOBILE PLAYBACK
You can connect mobile device to Nucu. Nucu will playback all the sounds from the mobile device
while connected.
Steps:
1. Connect AUX cable to the
a) Control panel’s AUX port
b) Mobile device’s AUX port
2. Select the desired audio from the mobile device and play it
Note: When the mobile device is connected to Nucu, the control panel goes into sleep mode.
Mobile device is now controlling the volume levels and audio playback.

7) ADDING SOUNDS TO NUCU AUDIO LIBRARY (WINDOWS PC)
1. Check that Nucu is powered off
2. Connect USB cable to the
a) Control panel’s Micro-USB port
b) PC’s USB port
3. Nucu will startup automatically after connecting the USB cable. Nucu now appears as a USB
device on your computer.
4. Copy your .mp3 audio files to Nucu with normal copy & paste operation.
–